1985 to 2005 25 Hp Johnson Evinrude Water Pump Impeller Replacement - Part 3 of 3

Подписаться 10 тыс.

Просмотров 39 тыс.

50% 1

This is part 3 of 3 video series showing you how to remove a 25 Hp Johnson Evinrude lower unit, replace the water pump impeller, reinstall the lower unit, and functionally test out the lower unit to make sure your new impeller is pumping water.
#ad As an Amazon Associate I earn from qualifying purchases. The below links are Amazon Associate Links or eBay Partner Network links
Replacement Water Pump Impellers:
------ 1979 - 1984 25 Hp Models -------
Amazon - amzn.to/2zdAQGq
eBay - ebay.to/2Q6ilxr
------ 1985 - 2004 25 Hp Models ------
Amazon - amzn.to/2qZJ0Ox
eBay - ebay.to/2PYOMxZ
--- REPAIR MANUAL ----
1973-1989 Outboards - amzn.to/2qRiiar
1990 and newer - amzn.to/2qU57Ws
Water Muffs - amzn.to/2TpIjuT
FOR STEP BY STEP INSTRUCTIONS VISIT HERE:
thisoldoutboar...
*** Above Links are Amazon and eBay Associate Links
Part 1 - • 1985 to 2005 25 Hp Joh...
Part 2 - • 1985 to 2005 25 Hp Joh...
This video applies to 20 25 28 and 35 Hp Johnson Evinrude Outboard Boat Motor models of the following years 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@AudieReagan Год назад

That is probably the best video I’ve ever watched on RU-vid!!

@nafyne 2 года назад

As a young 21 year old who made a (perhaps impulse) purchase on an old boat with an ‘89 20hp Johnson, you’ve been a big help with good info and just seeing how it’s done.. I believe myself to be fairly mechanically inclined, but was a bit hesitant to get into the outboard as I’ve never worked on one before and didn’t want to end up messing up the one I had just bought haha

@curtain2835 5 лет назад

Great job with all three videos on changing out the water pump impeller. I have a couple of inputs. #1; I was having a difficult time putting the lower end back onto the unit. It would go up to about 3/4" and wouldnt go any further. I came back in and reviewed your 3rd video and I figured it out. When I removed my lower unit, the black plastic exhaust tube came off with it. The problem is that it wont seat back in if you have it on the lower unit. I realized in your video that you had just the shaft. Anyway, I went back out and pulled the black plastic tube off the drive shaft and then fitted up into the housing. Then I installed the lower unit and everything went as you said. Thanks for the great videos. Saved me some $$$.

@jacquischinzig7049 4 года назад

I just did this job yesterday and that tube gave me absolute hell. With the new o-ring on I could not get it to fit into the hole in the leg. I ended up putting it onto the top of the waterpump, and combined with turning the motor a little so the prop shaft meshed with the motor spline it just seemed to go in when i did the bolts up. I'm pretty good with mechanical stuff but this job threw me a bit.

@lawnmowerman4040 4 года назад

Thanks I could not remember which way the plastic piece went , good job

@SilverMt. 4 года назад

thanks for the video , helped a lot. It is tricky getting the lower half back to the upper half and have the water tube line up. But turned out great.

@outdoorswithdwayne4385 5 лет назад

Awesome set of videos! Thank you for posting these. I'll be doing this to mine soon. Great clear instructions and camera angles!

@thisoldoutboard 5 лет назад

Thank you!

@bpml1969 5 лет назад

Really good video..the best description of this job I’ve seen yet. I need to do the same to my ‘94 25hp and you’ve just helped me out a ton👍👍Thanks I’m a subscriber now

@outdoorswithdwayne4385 5 лет назад

I have a 94 I'm fixing to do this to as well. Did you run into anything that was different from this video? This seams about as detailed as you can get but if there are any tips you have for the 94-25 I'd love to hear em.

@bpml1969 4 года назад

Outdoors With Dwayne I did this job on my ‘94 and got it back together and now the shifter won’t engage properly for some reason. I have to turn the prop a little to get it to go into gear now

@felipes.5707 5 лет назад

Really useful tutorial, thanks for take the time.

@mikebadilla6970 3 года назад

Thank you very much.Mike from buckley MI

@hanscuda Год назад

Is the washer at the top of the water tube a specific thickness of will anything that fits over the tube work?

@antoniomendoza5074 3 года назад

tanks that was a nice video !!!!

@adamsons2890 2 года назад

Fantastic video,best I’ve seen on RU-vid by far. Camera angles and explanations are so helpful. Thanks. I’m wintering my 98 Johnson 25 hp. I’ve got no water peeing out the telltale. I blew it out…. It seems to be clear. I’m going to replace the impeller with a kit from Amazon. I could not find your link,for the impeller,as you mentioned in your video. I have did subscribe to your channel.

@thisoldoutboard 2 года назад

Make sure your impeller key is engaging otherwise the driveshaft will spin and not engage the impeller

@andrewthomas4569 4 года назад

Great video! One question, you don't need any sealant on the lower unit to motor connection?

@thisoldoutboard 4 года назад

No you do not

@dbm12 3 года назад

Just asked this same question before I saw this. Mine has a chewed up seal in between, is this okay to pull it apart, remove the broken seal and put it back metal in metal?

@chongh757 5 лет назад

Great 3 step process.. I've followed your 3 video process and it went great on a 2003 20HP Johnson. My problem is now the Motor will only engage in reverse. To take it out of reverse I need to push the lever to Forward then to Neutral to disengage Reverse. If you push the lever to Forward is does not engage. Any idea as to what could happen?

@thisoldoutboard 5 лет назад

More than likely you have something Wrong at the shift rod linkage between the water inlet screens. I’d check that first and make sure you have everything right there

@chongh757 5 лет назад

@@thisoldoutboard Your right, I've mistakenly took out the lower linkage rod. (IDK) Do you know how high it should be? From the top of the base to the top of the lower linkage. (20HP Johnson 2003)

@johnmitchell8206 3 года назад

What do you do if there is still no water flow from discharge on top/ underneath the hood on right side of engine after you have replaced the water pump with factory kit?

@PCB-Designer 5 лет назад

Great video with detailed explanations. I removed my lower unit on my 94 Evinrude 30Hp to check the pump etc and a small plastic washer fell out. Any idea where this washer is from? It’s about the size of a dime. I watched several videos and no one mentions this washer. Thanks!

@jacquischinzig7049 4 года назад

Might have fallen into the leg from the engine housing?

@darrellsavoy8417 4 года назад

I NOW HAVE THE CONFIDENCE TO DO THIS MYSELF. ON 96 EVINRUDE. I WOULD THINK VERY CLOSE TO SAME PROCEDURE

@skippysounds541 3 года назад

Right around the 7:30 mark I notice water coming out of the small box on the top left side of the midsection. My 1994 Johnson 25hp does the same thing. I thought maybe I had a bad gasket. Do you know why it does this? Is that normal?

@CartersYTube 4 года назад

My 87’ Evinrude never pisses water out that tube. Is there a way to make sure that tube isn’t blocked before I have to tear apart the lower?

@thisoldoutboard 4 года назад

Run a small wire up it. Dirt dobbers can get up in there somehow

@dbm12 3 года назад

Is there no gasket between the lower and upper parts? Just got an 85 evinrude 2 stroke and mine has a gasket between there that is completely torn up. Thanks in advance for any advice

@thisoldoutboard 3 года назад

There is No gasket between the exhaust housing lower surface and the gearcase top surface

@dbm12 3 года назад

Thank you for the response. New sub. Strange that mine has a gasket in there. It’s completely torn up and water came out of it when I tilted the motor up. I was wondering why I couldn’t find a replacement lol.

@simonw2158 3 года назад

Hey, is there i reason why you are saying that the video applies to 20, 25, 28 and 35 hp models BUT not to 30 hp models? I need to change the impeller on my J30BACO model with 30 hp (model year 1985)

@charlesoaks2376 3 года назад

How do you keep the copper pipe up in the top hole mine keeps falling out

@Braveteacher 5 месяцев назад

We need help… our copper tube seems like it is missing parts? Bought a motor that someone else worked on and the copper tube just fell out… how does it attach at top?

@thisoldoutboard 4 месяца назад

Check out marineengine.com for engine diagrams