1998 Kawasaki ZX9R - Project Shinobi, Episode 16 - Complete Carburettor Rebuild & Assembly

Подписаться 16 тыс.

Просмотров 2,9 тыс.

50% 1

Hello everyone and welcome back to the Shed!
In this video, I am going to be continuing the ZX9R restoration series.
If you did not see any of the previous episodes then click the link below to see where I started.
• 1998 Kawasaki ZX9R - P...
Or you can look at the last episode right here!
• 1998 Kawasaki ZX9R - P...
In this episode, I am going to be putting the carbs back together using an All Balls racing rebuild kit. As you will see; they look lovely, clean and spanking fresh!
All the while making steady progress with the project!
I hope that you enjoyed this video.
Don't forget to like, subscribe and comment for future content from Kev's Shed!
If you wish to offer support to my channel and enable me to continue to bring you quality content then please check out my Patreon page at the following link - www.patreon.com/user?u=67741595 - Thank you.
Join me on the socials at the following links
Kev's Shed on Facebook - / 561477094498994
Kev's Shed on Instagram - / kevins_shed
Kev's Shed on Twitter - / catakev79

Авто/Мото

Опубликовано:

5 мар 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@AdeReeves 2 года назад

Must get mine out the garage ... bring it over to you to tune it up 😄

@jordangurney3831 Год назад

How this channel doesn't have more subs is beyond me. Excellent work as always, looking forward to your return

@brockmoore7816 2 года назад

Hi Kev, love your videos. I'm learning so much

@petecurran3995 2 года назад

Nice work, Kev! At the same stage with a v4 setup. Just at the time of refit, they've (butterflies) decided to go all sluggish. GT85 to the rescue and if that fails, strip down again! 🙄 hey ho, as they say.

@markconlon814 2 года назад

HI Kev, the heater hose with the kink in it needs to be taken off, and flipped over, the kink then goes around the idle cable!!

@KevsShed 2 года назад

Cheers bud, after editing I looked at the manual and noticed I’d fitted it wrong, cheers for the confirmation 👌🏻😎

@jasonjason7277 Год назад

i have enjoyed watching the Shinobi series. i look forwards to future instalments.

@hakim9821 2 года назад

You are all in one guy,you can fix everything..nice work👍👍

@ryanharriss7950 2 года назад

You tell it's post Christmas with all the quality street containers. I think many of us shed tinkering folk do the same 🙂

@myz06rocks 2 года назад

Lookin good and yes, glad you retained the previous jets!

@myz06rocks 2 года назад

Oh, if it’s the same as my E1 model, I thought one of the slide screws was missing also but that was the location of the screw that holds the choke cable bracket. Might be the same on yours also

@janeyl2805 2 года назад

Excellent work can't wait for next video

@nitramh24 2 года назад

I disconnected the TPS, and was clueless on how to adjust it again. But a guy on the ZX9R forum told me to run the bike without the TPS, and it works excellent without it. The tps does very little on a carbed bike, but if you have the tool, you can adjust it back on.

@willd5354 Год назад

I watched your whole series trying to figure out what's wrong with bought it at an auction, and it has the farings swapped out for stunt cages. I had a rattling in the engine, and the drive chain was jerking. After hauling it around on a trailer, the rattling disappeared and the oil light stays on. From watching your series I am guessing the previous owner did some clutch work and didn't assemble something properly. Thanks for helping me figure out where to start looking for my problem. I wish the series included reassembly videos though.

@KevsShed Год назад

I’ve got to get round to it! I’ll get there though! 👍🏻

@The-truth-is-valuable. 11 месяцев назад

Hi Kev - any possibility of you going on with this project?

@Garry2749 Год назад

Kev what happened to the rebuild of the 9r ?

@KevsShed Год назад

It’ll be back soon mate, as I said on my community page, I have a lot going on at the moment so RU-vid had to take a back seat. I’ll be back to making content as soon as I can though 👍🏻

@HalfdeadRider 2 года назад

I was so hoping you'd fit the throttle cables, as I have new ones to fit on mine, I hate carbbed bikes now lol It probably isn't too bad, but I'd prefer to not have to take the carbs off if I can help it. I've heard that these kits are not great too, makes me wonder if it's just people not setting them up right as they seem a well know and well used company for aftermarket parts, never used them myself.