What order do the wires go on.....I tried to start my car and wouldn't start...lights radio all fine...I popped hood noticed that the little bolt holding terminal on fell off...and the three cables were off...I tried putting them back on but still won't start...is there a certain order?
omfg. Thank You so much.... I ended up replacing the ends of the battery wires that one got tucked to the side and i completely overlooked that skinny little sucker... simple mistake my part that drove me nuts until I saw your video.. Again... Thank You Sir..
My car won't start after driving it in heat. Turn off car...go into store...come back out...won't start....usually just on really hot days of summer...any ideas? Thanks.
I love the fact be made this video as the hurricane was just forming lol . BORING!? I was on the edge of my key just waiting for that shit to start lol I don’t know about u Guys but I’m BLOWN AWAY lol
I have a 2003 ford focus and just got a new ignition cylinder put on I had payed the locksmith guy to come program my 2 keys made it turn on I go out n used after he made it turn on I turn da car off I wanted to turn it back on my dash board is dead no light at all n my car won't turn on anymore wat can it be???
Can any1 plz help me? 03 focus dohc zetec vin-3, cooling fans don't operate & every part is new! new head temp sensor(1 of it's wires is 12v & other is 5v reference) new cooling fan solenoid & new wiring harness(the old one was shorted out & burnt)( both ends now give off negative 12.56v when hot) I tested the fans & they spin when I apply 12v & ground to them but, I replaced them anyways & still didn't help! I bought a tested/used green 70 amp low speed cooling fan relay, I swapped out the 2 black relays with 2 from junk yard & the big grey cooling fan relay, I swapped it with my ignition relay since they are the same. Yet, still the fans don't work! I know that the fans spin continuously when I disconnect the cylinder head temp sensor but, that fried my alternator after several months so, I cut the 5v reference wire & extended it inside the car & ran a toggle switch & back to the other cut end & that allows me to turn my fans on & off. A;so, I bought a aftermarket cooling fan controller but, it is only set up to run 1 fan & idk which fan is for cooling & which is for my a/c??? now, my aftermarket cooling fan controller is a 70 or 80 amp set up so, I might be able to run both fans but, since the focus head temp sensor is a 2 wire set up, which wire do I use to control the after market fan controller & can I still keep my factory temp gauge? Right now, when I use the toggle switch to operate my fans, I loose my temp gauge while the fans are running & it works again when I shut the fans off! it is so frustrating & I REALLY NEED HELP! ANY & ALL ADVICE IS WELCOMED! Keep in mind that everything is new! the temp sensor, cooling fan & the cooling fan solenoid & wiring harness & I have replaced the relays with other ones to see if maybe that would have any affect? I just removed every ground wire I saw, sanded till I saw bare metal but I applied aluminum anti-seize between the chassis & the ground & im not sure that was my best idea but, I don't want it to rust. it's aluminum so, hopefully it will promote good ground! ANY ADVICE IS HELPFULL!!! THANK YOU! P.S. Everything else works great so, this cooling fan issue has me stumped!
Help!!!!!! We have a 2001 Focus .. just died on my son as he was driving , now it will not crank, the dash lights do not come on, and windows will not roll up. Radio and lights work fine. All connections good and the battery is fine and clean of any debris. Please let me know what this could be and what to do. The security light blinks normal , not fast & blinks all the time. Please help!!!
u need 2 clean the corrosion off ur terminals.water & baking soda but use very little water & carefully rinse it when done. (tip battery 2 one side just a little)so, when u rinse it, the water doesn't touch both terminals at the same time!