4L60E Teardown, No 3rd Gear 

Not to many issues here thank god.

We do that with Retail, alittle harder with wholesale to have them contact the client to bring the car back, sometimes even the retail clients do not show when we ask them to come back. Thanks for the suggestion

what year is this

I have a samsung. What brands do you recommend?

@@GaryFerraro Samsung has made some really great cameras, but they seem to have gotten out of the business of making video cameras for the most part I think. So from the look of the image, I'm guessing that yours might be a camcorder that is pretty old at this point? I guess on the whole, there are a lot of small Sony camcorders from recent years that would be a pretty big upgrade in image. I usually use bigger, interchangable lens cameras, so it's hard for me to give a solid suggestion on a recent camcorder that would be one of the best ones to choose. My impression is that there are lots of recent models from Sony, Panasonic, maybe Canon, and maybe even Samsung that might be good options... If you did want to move to an interchangable lens camera, which would be a lot more expensive, and probably a lot less convenient to use, then I could actually offer suggestions.

@@GaryFerraro I explained in my other answer why I can't offer a really good suggestion that is right on point, but from looking at what Marcuspix on RU-vid has to say, I think I might be inclined to try a Sony CX405 for taking some better videos around the shop. It's not super expensive if it gets ATF or trans gel all over it or whatever, and does a pretty nice job!: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KmZH3rGjjlQ.html

Bushing when rebuilding the trans?

@@GaryFerraro Like the bushings for the shifter on a manual. I have a lot of play when shifting gears and it feels very sloppy.

Technically no, but if the fluid is really bad and a lot of debris in the pan you may want to consider it, can't really get them clean inside

should have 6L80, converter going bad is common

Should I take transmission apart and inspect or just replace converter? thanks for your help.

@@Samll19821 I would drop the pan and see how much debris is in the pan, probably will need to be overhauled

Thank you, as soon weather gets better here in minnesota I'm going to start with that project . My 5r55s still running after replacing overdrive sprag 4 years ago, your videos helps a lot.

you can, as long as it air checks ok. Check the pressure plates, check the snap ring, load up the new parts and air check, if solid you should be ok, If a lot of debris you may want to take the drum apart for cleaning

It Happens, not to often thank god

possible hanging 2-3 shift valve, maybe solenoid issue as well

Never really found the smoking gun, i did check that and seemed ok, put in new 3-4 piston, double checked the Boost valve, no leaks, put ne rings on input shaft, everything air checked good and the drum held pressure, so went back together with it

more than likely was slipping due to low line pressure as a result of low fluid level

No, Units are different

@@GaryFerraro ok is it the speed sensor inside I just counted the pins one is thirteen and the other is fifteen I believe

If your working with 4L60E That is the band

@@GaryFerraro I have done a full rebuild on this unit it's being commanded for second gear but when it goes into second gear it just runs away even put different valve body in and still have the same even done the Corvette servo I am lost on this unit any help would be appreciated

I'm sure it developed a leak

most liked is 4L60E, most disliked is 5L40E

any experience with the AW55-50sn? I'm curious how many of these you've done these and at what mileages. I have a Nissan Quest at 156k with this transmission and unfortunately it is succumbing to the infamous 2-3 shift flare.@@GaryFerraro

could you send me a picture of where the checkball goes, my e-mail gsferraro@yahoo.com