88-00 Honda Sloppy Shifter FIX Step By Step

Подписаться 11 тыс.

Просмотров 9 тыс.

50% 1

The is the proper complete way to fix a Honda or Acura sloppy shifter this will not correct transmission internal issues but will help prevent premature wear on the system.
The common parts that wear out are below the links help the channel and cost you ZERO.
Change Lever Dust Seal A:
amzn.to/3Ya7GAY
Change Lever Ball Seat:
amzn.to/3majeXn
Stabilizer Bushing Kit
amzn.to/3y3ygkA
#efcivic
#crx
#civic
#acura
#honda
#sloppyshifter
#savetheefs
#classichonda

Авто/Мото

Опубликовано:

28 фев 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 30

@oldskool1979 18 дней назад

I just had this done on my 1990 crx si today

@hemaci9167 Месяц назад

I was looking everywhere for the size of the bolt, thank you very much sir

@DIYKAI Месяц назад

to replace the pin?

@90Rex Год назад

The shifter arm that you say there's not much to rebuild on is the part that causes the most play. When that 2 way universal joint at the end gets just a bit of play in it you have amplified slop in the gear stick. you drill out the rivets, replace the bushes inside (whether it be nylon or brass you can buy em online) and then use bolts to get it back together.

@DIYKAI Год назад

Yes that’s another way to go Lucky these ones were ok…..thought about fabricating a u joint or something

@gasnation6968 9 месяцев назад

do you happen to know where i can find that bushingB

@DkpProductions 9 месяцев назад

My linkage is incredibly bad, I have a video of it. Looks like I'm out of gear lol

@DIYKAI 9 месяцев назад

Is in on the tube?

@DIYKAI 8 месяцев назад

they are not sold anymore you would have to make some or something

@oregonfelder1 Год назад

LHT performance used a ball peen hammer to lightly hammer the riveted area to tighten up a little of the free play. It isn’t supposed to be floppy, but not supposed to be super stiff.

@oregonfelder1 Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-0HBRIPazikc.html start at 2:05.

@DIYKAI Год назад

Yes we seen Johns video he does great work ours was not bad maybe a thousand or 2 of play the bushing is what was worn in ours

@miclomusic805 Год назад

Thank man ! I keep putting my boot on the wrong way I suffered a serious money shift because of it 🤦🏽‍♂️ Whole linkage fell out the bottom hanging on my exhaust, Do you know if the connection part with the pin and u joints goes up or down ? I noticed the connection is offset to one side not sure which way to install haha

@DIYKAI Год назад

We will look at the diagram in the shop manual and reply back later today

@miclomusic805 Год назад

@@DIYKAI thanks I appreciate it big time 🙏 I tried to keep it all the same when removing but I just bought the car a few months ago not sure if the previous owner installed properly

@Wes_off_road Год назад

I have a question about the grill lights where can I get the original lights for it

@DIYKAI Год назад

What grill lights are you referring to

@Wes_off_road Год назад

@@DIYKAI the original lights that are on the ram grill? I bought the ones you suggested for your grill but they didn’t work so I was asking do you know where I can buy the ones that come standard on the grill

@DIYKAI Год назад

@@Wes_off_road ok got ya though you were commenting on this video. The original lights inside were cheap and we never found a replacement worth it….so we used flexible leds with sticky tape

@DIYKAI Год назад

@@Wes_off_road when you say didn’t work what happened?

@Wes_off_road Год назад

@@DIYKAI the lights I bought didn’t work because there not flexible