Absolutely new Unbelievable Homemade !!! for Cars Never seen Before 

2024 New invention for cars never made before 👇👇 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7zRfMtUs_D4.htmlsi=VkNr9-a4qE7uYoXH

Nice welding, but maybe there's a reason why these are not commonly sold . Huge risk involved .

This is a simple and interesting device, but it is only suitable for cars with a huge ground clearance. Most modern cars are not compatible with it. The device will only work with the back where there is a void. In front, there is the suspension, the engine crankcase, and its protection, there is barely 130 mm clear. In addition, a square pipe for heavy cars needs to be reinforced with scarves from the bottom to ensure sufficient rigidity. Because even in the video you can see how the pipe bends. After 10 lifts, it will take the shape of a hemisphere.

Great idea. Thanks for sharing that

Nice first attempt. But it would be more useful for cars that can't move under own power if the 4 rods were wider, and are inserted into receivers. This way you position it under the car, insert the 4 rods front and aft of tires, and lift. Lower the car elsewhere or when done, pull out 4 rods, remove the assembly and jack.

That's very good for vehicle's without a central jacking point, and yes you have to use jack stands.

Those welds at the end rods are impressive!

Definitely would have to get jackstands under it for support in case the hydraulic jack failed.

thats a good idea and well built. i would change piece in middle and make it go in the hole on the jack after removing the lift disc. but over all this is awesome

Absolutely brilliant well done mate cheers

Excellent job

Great idea, will be making my own. Will add a couple of threaded stantions like harbour freight to lift rear axle. Maybe insert heavy wall square tubing or solid square bar inside lifting beam for more center strength, weld in with rosette welds. Thanks again!

Really impressive tool, I will build one similar myself, but have ideas for modifications to where one could use it for cars as well concerning ground clearances to bottom of vehicle

I would definitely say test it on different weight cars so you know it’s tension strength. This is a great build but I’d like to know it’s weight capacity.

Sure is robust....and an awesome tool.... Thanks

Well done!

Bro amazing 👏

Ух ты! Классная идея!

Great idea for uniformity of lift. I also enjoy repairing my own vehicle. Vetri South Africa 🙏🇿🇦🙏

Very nice Welds!

Excellent time saver. Great video. Thank you!

great work

Definately a nice idea

I wouldn’t trust it with out blocks under the wheels, so if you have to use blocks why not just use ramps. It’ll be easy to weld some drop down stabilizing legs on it though , maybe some straps over the tires to fasten it down .. Pretty good idea 🤙

Great job on it like it

awesome idea !

Espectacular genio muy bueno me voy hacer 👍

Awesome idea. My truck is lifted and it’s a pain in the ass to Jack it up. This is perfect. 👍👍👍👍👍👍👍👍

Nice job 😊

thatsa great tool and could be modified for use on light duty trucks.

Nice, but where was the clip of the car driving up onto the round stock? While it was balanced on the jack, the round bars weren't on the ground.

Nice

This would make it easier to place jack-stands. Keep innovating! Nice

Genius!

Really good idea and awesome creating! Nice job! :)

I’m retired welder. Love mug welding! Squirty Squirty! Sweet idea!

I need to build one of those for a 3-point hitch to move my project cars around. Great idea! Just add a ratchet strap over each tire.

Великолепная идея и отличное исполнение! Меня оно навело на мысль для универсализации под разные базы и не только под колеса.. Огромная благодарность и удачных идей в будущем!🤝 Теперь я знаю, что и как сделать в гараж под джип и легковушку!🤝

Me gusta la idea👍👍👍

Great. Job. Thanks for Tip I am. Going Make one at My. Welding Shop 🙏🇨🇦

Awesome

Good job mate 👍👍👍

I love it! I want one! The sad part is I wouldn't be able to pick it up to get it on the jack. Bad back. 😢

I see a business opportunity here. Do the necessaries and see what happens. Brilliant idea!

Very cool idea! I believe I’ll make one

Super

Could use a little more distance between the tire bars.

Nice build. Thank you for sharing your video.

Nice I'll have to make one But lower profile

Excellent idea for lifting a car evenly to fit the axle stands. Very nice welding.

I hope my mechanic has one of these.

Thank you for the fantastic video! The advice on just using the jack without the need for a heavy metal bar is extremely practical. It makes the whole process more straightforward and helps save space in the workshop. Your explanation was thorough and very helpful. I appreciate the time and effort you put into creating these videos. Keep up the great work, and I can't wait to see more of your tips and tricks in the future!

Useful build to get one end of vehicle up on jack stands.

Definitely need to get a lower profile and a better jack with a lower profile jack the round bars will all sit on the ground and I would put a bigger round pipe in the center for the jack. Yes I would Definitely use hevy duty jack stands

Love it where can I buy it

I love it! This is brilliant. Ignore the negative comments.

A fun project and useful for certain applications. I always wondered if someone makes air-rams to mount permanently under a vehicle to lift either of the four wheels for a quick tire change like in the Indy 500 pits? Be nice if you could just hook up to a small compressor, lift either of the 4 off the ground, and it would always be there underneath for when & if you get a flat tire in the dark and/or during shitty weather.

I wouldn’t trust my life with that contraption! A couple of decent ramps, and couple of jack stands for redundancy are more than sufficient and you’ll get more space under the car.

This might be good for pick up trucks if you don't have long reach floor jack. Once up, drop on jack stand...

Looks safe🤪

Looks dangerous. The car could roll right off😳

One improvement I would do is add some gussets from back of wheel to about 3/4 of the way to the lift point. That would help on the deflection as you lift.

You left out the part where you had to back the car onto it to use it...

Not having the tools to build it i would BUY one of those jack systems….brilliant when you need to get under your whole car, just add a couple of jack stands and work in total secure comfort1👍👍👍👍

Great! Where can I buy one?

Love the idea, so why no just make it jack up both side but make it catch the shock or the axel or some other point that succure enough to lift both side. Your fab work was very impressive. Maybe just change your point of contact. Then you won't have to brive the vehicle over it and you could service everything under the vehicle without to hack up one side at a time!! Just my opinion brother!! Over all tho, great fab work!!

This is a awesome job you have done here. Just a little suggestion,maybe add a couple tabs on the round bars to front and back to put a ratchet strap on. Maybe on a slight up angle, just a thought.

I can't figure out when you would use this when 2 jackstands would suffice. Of course it is cool to make things I do it all of the time.

I need this lmao 🤣

The steel car lifting bar looks great. But your Center is not strong Enough! You will lift a couple of times then it will collapse in the center. Please do not risk your own life.

It's nice, but can you just jack on the center of the subframe to lift the front up?

This thing gives me anxiety but safety stands can help, also this contraption is for tall vehicles not low clearance ground cars, overall nice time saver!

Great job , s that wheel under pressure?

This is as safe as the old style bumper jacks.

👍👉💟

I was going to buy air powered since they use this idea to lift buses. This is s good idea of jacking it up to wood cribbing stands

Se o carro mexer pra frente um pouco ele cai, ficou perigoso, se fizer as barras um pouco mais distantes para abracar melhor o pneu e deixar o centro de gravidade um pouco mais baixo vai ficar perfeito! Parabens pela idéia criativa!!!!

Das ist ja mal richtig geil. 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

Congratsulation

Other than an oil change, what can you do with this contraption?

would be a lot better used with a low clearance jack to bring down the height of it, great for transverse engines where they either have no jack point at the front or its off set due to the engine, g'box layout

Gd idea mate ❤

Nice. But just gets in the way !

That's some high dollar metal

👍

Reminds me of a tow truck lift.

How do you change the tire+wheel with that?

I’d like to see something similar for raising large tires to install on lugs..I have a truck with 20 in wheels and 35 tires and I’m older now those things are heavy…maybe something exist for that?

If you have a live axle rear end, just put the jack under the diff housing.

Good idea ... just reinforce the center part it's bending alot..

Can buy a similar one at harbor freight

estupendo

I like it, but I’m not going under that car. LOL

très pratique lorsque tu veux retirer les roues arrières 😄😄😄

I will continue using my drive up ramps.

Or you could just jack it up with just the jack and accomplish the same exact thing without having a giant heavy metal bar taking up all kinds of room in the shop

Wouldn't need that often, could just use the jack by itself. That would come in handy for vans with the twin I- Beams though. You can't lift them up dead center in the front.

Just use subframe mounts as jack points instead? What do you do when it's up in the air? You'd still want something other than a jack to hold it up while you get under the car. A pair of ramps would be even faster to use and easier to store. Nice metal work but not sure what problem it's solving!

What is the brand of that blade, and can it be used on a regular chop saw such as a Rigid 14" chop saw? I like how it doesn't put off a ton of sparks and all the dust that comes from typical chop saw blades.

Good for getting the whole front up so you know the jackstands will have the same height when you put them under.