No video :(

Adjusting a Sheet Metal Hand Brake

Подписаться 8 тыс.

Просмотров 13 тыс.

50% 1

Sheet metal hand brakes are used to bend sheet metal for roofing and other purposes. This 15-minute instructional video was filmed at the 2018 Slate Roofing Contractors Association conference in Grove City, PA, by Joseph Jenkins, executive director. Demonstrated by Chris Paulin, Paulin Slate and Copper, Akron, Ohio (PaulinSlate.com). More about the SRCA: slateroofers.o....
Here's Korby's demonstration: • Making Curved Copper F...

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@user-hu3cq2no9p 4 месяца назад

Thanks Joe. Just picked up an old Chicago 4ft 12 Gauge. Great video!

@lenBrill1971 Год назад

Thank you from Stolairus Aviation in Kelowna British Columbia Canada. Our brake had a mind of it's own. Hopefully after your vid and some cuss words I can adjust our karen brake. 🇨🇦👍 Edit - wow!! Those large adjustment nuts at center of the deck(anvil?) and leaf were CRANKED. The deck had a rise of over .100" +. at it's center. I zeroed (no load) all them big adjuster nuts and the break relaxed. Then I micro tensioned those just enough to make infinitely tiny adjustments. That's all they needed. This 12' brake bends perfectly now. 👍👍

@christopherpaulin5548 Год назад

Glad you got it bending perfect Len 👍12 footers can sometimes be tricky. That's the number one problem I see with brakes: the center adjustment nuts are usually cranked way too much. Nice fixed wings, I'll take a plane ride 😉

@MulticameraProduction Год назад

Very informative 🤘

@christopherpaulin5548 6 месяцев назад

Thanks for the kind words, and also to Joe for making and editing the video

@rocktheboat56 3 месяца назад

Currently struggling to get our 12ft 16ga brake adjusted. I can get the ends good but the bending leaf slips in the middle when I go to bend resulting in the middle of my bend being wide open and ruined. Chicago dreis and krump

@user-ic2uh9fr4r 9 месяцев назад

My bending leaf is sagging in the middle my angle metal is about in the middle of the leaf Chicago 1422 is the model. This causes the leaf to bind and really not work . A new to me brake. Any suggestions on what to adjust? Thanks Jason

@christopherpaulin5548 6 месяцев назад

Hi Jason. Is the bending leaf sagging down towards the floor, or out away from the brake? If you can make a video of what is happening, that would help

@user-ic2uh9fr4r 6 месяцев назад

Yes it did not have the angle iron on it so move the one original up and got one more. Helped but still not doing the trick with the light gauge metal. Plus now I can’t do style D drip edge very well. I had to space out the end of the lower angle iron to pull out on the bending leaf it is so bad

@mmroofs 2 года назад

Great video, thanks for posting ! Do you have a follow up video with Corey?

@jcjenkins01 2 года назад

Korby. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-aWK0ep3YQBo.html

@mmroofs 2 года назад

@@jcjenkins01 Thanks joe!

@sumtingwong2162 2 года назад

Thanks for a great, no b.s., informative and straight to the point video! I bend so much metal at work I feel like I'm married to that brake, but now I can treat the old gal right!

@kylereichstein7578 Год назад

Hello! I have a European sheet metal break, the centre doesn’t seem to crush the steel when we need to crush. For example, when we make out starter flashings and we need to crush a safety edge. It will crush the ends, but heading towards the centre it does not crush the way we need it to. This leads to some of our accessories bowing. Any advice? There are a dozen nuts and bolts but I’m not sure where to begin adjusting and how tight to make them.

@christopherpaulin4886 Год назад

Release all tension on the clamping and truss adjustment nuts, so that the top leaf just holds the material. Then adjust the tension as necessary to achieve a consistent hem. Hope that helps

@kylereichstein7578 Год назад

Thanks Chris!, This is one of the first things I did. I figured letting off all tension and then retightening everything would be the answer. It’s not. And it’s frustrating!

@christopherpaulin4886 Год назад

RR, get the frustration, I've been there. Feel free to e-mail me and we can get you squared away there

@christopherpaulin5548 11 месяцев назад

What is the make and model of the brake you have?

@Owais_Ghani 11 месяцев назад

Hi, We have a Pressure Brake Bending machine and whenever we are bending Aluminum Sheets with it, it breaks the sheet. We are unable to use it for thin aluminum sheets. Is it possible to reduce the tonnage of that machine and if yes then how so ?

@christopherpaulin5548 11 месяцев назад

Think you're asking about what we would call a press brake here in my area of the United States. Press brakes are completely different machines: usually hydraulic or servo-electric operated or some combination of the two, use dies, and therefore operate in a very dissimilar manner to a hand brake, so your question is well outside the scope of this video. Try searching for "press brake", and I hope you can get your question answered.

@David-rg5cw Год назад

Hey Joe. Have you read about JADAM Korean Natural farming's use of humanure in producing fertilizer? Any thoughts on this method? Thanks

@technofeeliak 2 года назад

I can't use this.

@aidibachir6085 Год назад

مرحبا لا يستحق أن تعبد مخلوق ضعيف يموت لم يخلقك فقط خالقك يستحق أن تعبده وحده لا شريك له من فضلك تعرف على الاسلام الحياة قصيرة تنتهي في أي وقت ونعود لربنا ليحاسبنا اني ناصح لك أمين وشكرا

@user-ic2uh9fr4r 9 месяцев назад