AirLift Performance 3P/3H controller tutorial 

Cause you probably have sleeve in the front and since there’s weight in the front you have to air up all the way first so your bags settle and then you put your ride height is gonna be like a clunking sound and if its not that than idk but that’s what i do to not have that problem

It all depends on how u route the exhaust hose. I just got mine installed today

You have to have it on a preset before you shut the car off, if you manually aired up or down before then it won’t raise on start.

gillixexik but I unplug the controller because it holds power getting it re-wired this week

Arun Proothi i only ever do it when my car is stopped. Of course the controller will do whatever command you give it but it wouldn’t be the safest thing to do it while moving.

You can but you will have to use the corner buttons instead of the preset

you have more pressure in the tank

@@xtocy96 😂😂

Miggy EK4_FB6 do you mean is it supposed to stay on once the car is off? If that’s what you’re referring to, no. If it’s while you’re driving and stuff, yes but that can be adjusted in settings

Sergi Rodas my screen stays lit all night with my ignition off. I don’t know if that’s normal or not.

Miggy EK4_FB6 I have the same problem which I’ve been too lazy to fix. Your power wire for the bags is connected to a fuse receiving constant power meaning it’s on all the time even if the car is off. You need to get it connected to a fuse that only receives power when the car is on. If you don’t get it fixed, it’ll start to drain your battery

Sergi Rodas okay thanks. Do you have an after market exhaust? If you do how are you avoiding the exhaust piping from touching the rear passenger bag? Mine is, I don’t know if its because of my 3 inch full cat back piping?

Miggy EK4_FB6 i do have a 3 inch cat back. Gotta heat it up and bend it. I also have some heat wrap around it

Top button is only to air all the way up or until you let go. Bottom button is only to air all the way out to 0 PSI

I always wait for every thing to be at my preset. You can drive while tank is filling back up

Nathan Machado If you have it set to maintain a certain PSI then it will adjust while you are driving. I would not recommend airing out all the way while driving though.

KK Prince yes it is, unless its winter and cold. If condensation get into your lines and it freezes you wont be able to air up and drive.

@@SwtLeo oh jeeze...thank u I appreciate your response!!

Ok so basically stay aired up in winter?

@@MrNiceGuyGTL there's a release button that cleans out the lines. When it gets cold you should press is once a week so it gets the condensation out. You're able to lower it when its winter.

@@dragswolf8 wheres the release button?

Did you ever get an answer to your question?? Cause I have the same problem. It says put the manifold in pairing mode and I don’t know how to do it

Sounds like their may be a leak somewhere. I’d check the air lines and bags for leaks

I’m having the same problem and now my controller says no ecu and changed to manual mode

That means you have an air leak somewhere in your tank. Check all plugs/fittings on your tank

Robert Reyes hi rob, great minds think alike.

@@ShumileSwift It all depends on the bags, for mine the front are max 150 psi and the rear are 125 psi max. (They might be rated for more but that's what the manual lists for max PSI.)

Been asking everywhere. Still no answer.

Any chance you found an answer to rotating the screen?

Tylor Dowell if you update the firmware, it will ask you which orientation you want the screen to be. So maybe try updating firmware then selecting “horizontal”

Need to do via app only

@@TheLocalBikeGuy You probably found it by now but you can undo 2 screws a the back of the controller pop out the button pad and rotate it.

Max psi for the bags is 125 I believe. So I personally wouldn’t put more than 80-100. But every vehicles system is different

No it goes higher. Before it became popular it was used in snowy conditions to allow cars to be higher than stock

+Sergi Rodas thanks also if you remember the instructions say i cant have thread showing on the coil. Do i have to adjust it all the way down?

+Sergi Rodas thanks also the manuel said the threads cant be showing on the shocks, out of the box they came all the way up. Do i have to adjust them all the way down until they aren’t showing? It would be great if you could send me some pictures and info of your setup since you have had these for a while already