BENT Trans Beam Repair (Tacoma)

Подписаться 24 тыс.

50% 1

In this video, I show you how to repair a bent transmission beam on a Toyota Tacoma as well as replace the transmission mount. This is part 2 of the trail repair series and for this repair I do recommend having a hydraulic press for this purpose.
Here's the link to the parts used:
Beck Arnely Motor Mount: amzn.to/3EwOjuc
Here's the link to the rest of the series:
Part 0 - Damage Report: • Everything I broke on ...
Part 1 - Motor Mount Replacement: • Motor Mount Replacemen...
Part 2 - Tacoma BENT Transmission Beam Repair: • BENT Trans Beam Repair...
Part 3 - Rear Diff Leak Repair Tacoma: • Rear Diff Leak Repair ...
Part 4 - U-Joint and Center Bearing Replacement: • U-Joint Updates and Ti...
Part 5 - Tacoma Bed Separation: • SOLO Tacoma Bed Removal
Part 6 - Bed Separation: • SOLO Tacoma Bed Removal
Part 7 - Shackle Flip Design: • Shackle Flip Design Ta...
Part 8 - Shackle Flip Installation: • Shackle Flip Installat...
Check out my links:
Main Store: store.kflo-krib.com
Amazon: amazon.com/shop/kflostacomabuild
Patreon: patreon.kflo-krib.com
IG: KFlo_Tacoma
FB: KFloTacoma/
00:00 - Intro
00:24 - To my new viewers
00:42 - Work Recap
00:58 - Current Setup
01:12 - Removing Driveshaft
01:48 - Removal Thoughts
02:36 - Transmission Mount Removal
03:43 - Cross Beam Removal
07:11 - Separating Cross Beam from mount
07:26 - Cross Beam Damage Report
07:59 - Using the Press to Straighten Beam
09:12 - Transmission beam test fit
09:44 - Prepping Surfaces
10:44 - Comparing the two transmission mounts
11:41 - Reinstalling Crossbeam and mount
13:47 - Outro
#ToyotaTacoma #ManualTransmission #Engineer

Авто/Мото

Опубликовано:

21 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 5

@sariego9 10 месяцев назад

Ok, cool this is useful. Oddly, the stealership removed that heat shield and tossed it, they said it was just full of rocks and mud and was only there to make noise. Are you making your own skids?

@KFloTacoma 10 месяцев назад

You do have the crawler box too so it moves your front drive shaft a bit further back. from what I can deduce, I think the heat shield is to protect the u joints from excessive heat so we don't lose the grease in those joints. With regards to the skids, YESSIR! I'm just very slow when it comes to mods, since I do make most of my mods essentially from scratch LOL. I'm working on a shackle flip for long travel on the rear at the moment, you'll probably see that on IG first

@sariego9 10 месяцев назад

@@KFloTacoma shackle flip is good yeah. Can't wait to see it!

@michael184272 10 месяцев назад

Of course another #10...could the transmission of stayed in position without the transmission jack or does it's weight require support at all times without the cross member there? I understand that the transmission jack enables you to lift the transmission higher to get access for the cross member and hands etc

@KFloTacoma 10 месяцев назад

Thanks for watching, George. To answer your question, the motor and transmission assembly is supported by the motor mount and the transmission mount. If the transmission jack was removed, it over stresses the motor mounts and premature wear or completely damage those motor mounts