Тёмный

Building A Custom Landing 

YOUFLOOR Flooring Tips and Tricks
Подписаться 23 тыс.
Просмотров 22 тыс.
50% 1

Painters Tape
amzn.to/3I0tr11
Today, we go through the steps we took to build this custom stair landing. On any normal situation, the standard is to install 3/4 inch hardwood with a stair nose, however this customer wanted a solid platform in lieu of flooring the landing so . . . that is what we did! Check it out if you haven't already!
Please leave your questions in the comments and I will see you on the next one!
If you have a detailed question, please send 📷 pics of the problem and your question to
📧 YouFloor.net@gmail.com
Per Your Request 👇
☕️ Buy YouFloor A Coffee ☕️
www.buymeacoffee.com/youfloor
Thanks to all the supporters and subscribers of this channel! 😁
If You Like This 📺 Channel, Check Out Our Other Channels Below:
📱 Rent This Flip That
/ @rentthisflipthat
📱 Late Crime Date
/ @latecrimedate
📱 iFloor . . . with him
/ @ifloor...withhim9721
🌐 Facebook Page
/ youfloor.net
🌐 Facebook Group
/ 769392503713895
Tools You May Or May Not Need: (Affiliate Links Below):
Dewalt Oscilating Tool
amzn.to/3yRKyhv
Dewalt Table Saw
amzn.to/3wPyf2H
Dewalt Razor Knife
amzn.to/39b8JN5
Contour Gauge
amzn.to/3L7HDnx
Tape Measure
amzn.to/3wJj7Ue
12inch Combination Square
amzn.to/3Mml8vm
Stair Tread Template Tool (options)
amzn.to/3xMg0wx
Stair Tread Template Tool (options)
amzn.to/3NPnFA5
PL3X
amzn.to/3CpIKfx
Oscillating Saw Blades
amzn.to/3vdMMnS
Safety Glasses
amzn.to/3Fjvuun
Johnson 6 Ft Level
amzn.to/3I71uBK
Dewalt 18 2” Gauge Brad Nailer
amzn.to/3MFYjUW
Dewalt 18 2” Gauge Brad Nails
amzn.to/3CRWeSt
Bostitch 18 Gauge 2” Brad Nails
amzn.to/3H8aZmH
Porter Cable Air Compressor 6 Gallons
amzn.to/38QbhjQ
Titebond Wood Glue 16 ounces - 2 pack
amzn.to/38QmBfU
Hardwood Flooring Jack
amzn.to/3RyzCN7
Framing Square Stainless Steel
amzn.to/3Y6fh4k
Framing Square
amzn.to/3X2Lx77
Dowel Rods Wood Sticks Wooden Dowel Rods - 5/16 x 36
amzn.to/3jsyHBq
Strap Clamp
(we bought ours at harbor freight - this little handle would’ve been nice to have lol)
amzn.to/3x4yfMw
6", 2 Pack, Clamp, Mr. Pen- Bar Clamps For Woodworking
amzn.to/3JL3K6e
Jorgensen 2-pack Medium Duty Steel Bar Clamp Set with 600 lbs Load limit, 24-inch
amzn.to/3DJSbrM
Painters Tape
amzn.to/3I0tr11
DISCLAIMER: This video and description contains affiliate links, which means if you click on one of the product links above and make a purchase, I will receive a small commission (at no extra cost to you of course). This helps support the channel and allows us to continue to make videos like this. Thank you for your support!

Хобби

Опубликовано:

 

5 фев 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 26   
@jarrodledsinger6391
@jarrodledsinger6391 Год назад
One of the best yet Z! Content just keeps on getting better each time!! Keep at it! 👍🏼
@YOUFLOOR
@YOUFLOOR Год назад
Thanks buddy👊
@vanderpant2116
@vanderpant2116 Год назад
So glad I found your channel 👍👍
@YOUFLOOR
@YOUFLOOR Год назад
So am I. Thanks for the support. Welcome to the family.
@deaddeerwalking5283
@deaddeerwalking5283 Год назад
Looking forward to seeing you finish the stair project with top stair and the carpet wrap.
@YOUFLOOR
@YOUFLOOR Год назад
Cool man, thanks for keeping up with the progress. Thanks for the comment
@lorenzobandini9302
@lorenzobandini9302 Год назад
very good video, It gave me some ideas about the stairs I am finishing after removing a nasty carpet.
@YOUFLOOR
@YOUFLOOR Год назад
Awesome. Good lucknon your project
@cranstonwilliamsworth9644
@cranstonwilliamsworth9644 7 месяцев назад
Thanks for sharing, lots of great ideas!
@YOUFLOOR
@YOUFLOOR 7 месяцев назад
Appreciate the comment
2 месяца назад
Great video. Where did you buy your oak treads? I need to buy 52 inch treads for my stairs.
@centralfloridasprayfoam4870
@centralfloridasprayfoam4870 4 месяца назад
were all your runs and rises the same? Cant they be off a tad? I noticed my 1st step of the entire staircase was lower than the rest. great stuff thanks
@jessea.8320
@jessea.8320 2 месяца назад
I just finished cutting and gluing my landings and staining my treads, now I am ready to install, but my 18 guage Riobi Airstrike is not strong enough to push the 2 inch nails through the 1 inch oak. Some go in, some don't/ I was wondering if an 18 guage pneumatic brad nailer is better. Please advise
@mingshar2591
@mingshar2591 Год назад
Good job 👏
@YOUFLOOR
@YOUFLOOR Год назад
Thanks Ming
@sedtaylor
@sedtaylor 6 месяцев назад
Man, I need you to build me one of those. I am stuck on what to do with my landing, and this was awesome.
@YOUFLOOR
@YOUFLOOR 6 месяцев назад
Well, thank you. I appreciate that. You never know what you can do til you try. Thanks for the comment
@sedtaylor
@sedtaylor 6 месяцев назад
I think I will try it. Thanks. @@YOUFLOOR
@austinr.6452
@austinr.6452 6 месяцев назад
Question, how many times did you run the treads through the table saw 59 make the groove? I’m sure a least a couple times to take in account the table saw blade width and the dowel width. I am assuming you measured the height of the table blade as well for sticking up Thanks in advance!
@YOUFLOOR
@YOUFLOOR 6 месяцев назад
I'm not sure it I know. I did run them all before I change anything so they would al stay consistent. But it was really trial and error. Kept cutting and testing until both plank cam together. Practice with a couple scrap pieces til you get it dialed in. Hope that helps. Thanks for the question.
@Tex8814
@Tex8814 Год назад
Great job. Looks awesome. Could you tell me how far that bullnose sticks out ? Is there a standard length to overhang it ?
@YOUFLOOR
@YOUFLOOR Год назад
Hey, Tex. There really isn't a standard for how big a stairnose should be. You just don't want to make it too big as you don't want to trip going up the steps. Codes for your run are supposed to be 10 inches. So if you are using 2 x12 with 1/2 inch thick risers. Your stair nose would be 1 1/4 inches. 2x12 are 11 and 1/4 . So 10 inches plus half inch riser leaves an inch and a 1/4. You can fudge your finished treads, but generally, mine hang over about an inch with these. And then I usually nail a cove molding underneath. Makes for a nice Looking stairnose. However, this customer did not want cove molding under the thread. Hope that answers your question. Thanks for the comment
@BrothaJeff
@BrothaJeff 8 месяцев назад
Are you using an 18 gauge nailer?
@YOUFLOOR
@YOUFLOOR 8 месяцев назад
Yes sir I am. Thanks for the question
@danvo8096
@danvo8096 2 месяца назад
Do you do for business or contracts?
@YOUFLOOR
@YOUFLOOR 2 месяца назад
I do both
Далее
DIY TREADS AND RISERS
17:28
Просмотров 82 тыс.
How to Install Stair Treads & Risers: Pro Techniques
26:05
Stair Renovation | Finish Top Step With Carpet
19:08
Stain Stairs like a Pro
11:13
Просмотров 3,2 тыс.
Tiny motor, big power
0:25
Просмотров 26 млн
KINDNESS ALWAYS COME BACK
0:59
Просмотров 127 млн