Chapter 23 - Troubleshooting Panel NFS-320 NOTIFIER 

Hola gracias me da gusto! Espero puedas checar los demás videos!! Q estes bien!! ...

You have the same trouble?? Thanks for watching! Stay safe and have fun! ...

@@lumenfirealarms Yes before I replaced it

Ohh cool!! Have fun! ...

Hello thanks for watching! I don't know but mine lasted almost 7 years but I use this panel only for training and demo board! That's why is not always on! Stay safe and have fun! ...

Hello thanks for watching! What model of panel do you have? And what did you do to check this trouble? My suggestion is to remove the main wire of loop 1 first to know if it is the board or your wire/devices! Is this the only system trouble you have? Stay safe and have fun! ...

Mines is intermittent ground fault on L1. Using my analog meter. I measured 50ohm from negative or positive leads to earth ground. I also reads dc voltage ranging from 2-5V DC any leads to earth ground. Pms advise. Thanks

Hello yes I will share more videos about NFS2-3030! thanks for watching! Stay safe and have fun! ...

Hello thanks for watching! Sure I will make a video about it very soon, stay safe and have fun! ...

Yes they are really fragile! Thanks for watching!! Stay safe and have fun!! ...

Hello thanks for watching!! I don't have any video about that trouble! But I think I'm gonna make one really soon! But what you need to do! Or at least what I do! Is backup the data base then use the info to create a new one and download it to the panel! And if I notice the firmware is not upgrade I also do it!! Works really good for me doing this!! Stay tuned and check my other videos when you have some time!! Have fun! ...

Hello, yes you need to make a backup thanks for watching! Stay safe and have fun!! ...

Hello thanks for watching! The right way is using verifire tools! So you can download the data base again! If you don't hace verifire tools you need to do it by hand! Stay safe and have fun!! ...

Hi Sir.. I have install verifire in my laptop but can't connect, trouble in port..please give me solution..thanks

Hello! What panel are you trying to connect? Check your wire USB b port printer cable, check your laptop configuration and the gateway configuration tool! Verifier tools version? Stay safe and have fun! ...

Hello thanks for watching! The model is BR2335 3V and you can find it at Home Depot or any electronic store! I will make a video about it this one is easier to replace! Stay safe and have fun! ...

@@lumenfirealarms Thanks for the quick reply and help!!

You're welcome! Hope you can check my other videos!! ...

Hola q tal por el momento no tengo alguno espero en un futuro cercano lo pueda realizar pronto subiré videos de programación con el software de Verifire tools!! Te agradecería si compartes mi canal y te suscribes!! Ojalá puedas checar los demás videos!! Q Estes bien! ...

Hello thanks for watching!! I need more info so I can help you! You can check the manuals to see what you need to check or do!! Hope you can watch my other videos! Stay safe and have fun!! ...

Hello thanks for watching! Stay safe and have fun! ...

Hello thanks for watching!! I don't that never happened to me!! Could be database corrupt!! Hope you can check my other videos! Stay safe and have fun!! ...

@@lumenfirealarms Thank you very much again!. And, could be a problem with the CPU? in this case, I'll must could be found an error code, right?

I think it could be the firmware of the panel, if you have a Verifire tools license I recommend you to upgrade your panel to V27 and check if happens again! If you have a picture I would appreciate if you share it! You can look for me on Instagram same name Lumen Fire Alarms do we can keep in touch! Have a good day!! Stay safe and have fun!! ...

You've probably fixed this, but I'll put it here just for future viewers. Last time it happened to me, it was a faulty KDM-R2, the damage was caused by prolonged exposure to heat and humidity. The time before that was caused by a pinched ribbon cable.

Hello thanks for sharing!! Stay safe and have fun!!! ...

Did you mean battery fail charging?? Could be the fusible 15 amp, you need to put a new one! Look for me on Instagram and I can send you pictures! Thanks for watching!! Stay safe and have fun!! ...

Hello thanks for watching!! I can't help you right now, but you can look for me on Instagram and send me some pictures and then I can give you my suggestions! Hope you can check my other videos!! Stay safe and have fun!! Don't forget to share and subscribe!! ...

Hello I'm glad you like it! Thanks for watching! You can get the software Verifire tools if you pass a Notifier training and certification course! That's the right way! Stay safe and have fun!! ...

Hi. Dear sir, please send me information about training ​@@lumenfirealarms

Hello thanks for watching!! For Corrupt System Troubles: Logic Equat, DVC Audio Lib, DVC Database, DVC Program and Program yes you must use Verifire Tools and re-downloaded the database or cleared all programming and then re-entered! I hope I can make a video about this really soon! Stay safe and have fun! Hope you can check my other videos! Happy holidays to you! ...

Hello thanks for watching!! I have no idea I'm gonna search info about the fire Lite panel!! Stay safe and have fun!! ...

@@lumenfirealarms Hello. I am probably going to get a nfs-320 or 640. I have 3 quick questions about the panels though. 1. How long does the NVRAM battery last before it needs replacement? 2. How long will an NVRAM battery last in a power outage to keep the programming in its memory? 3. Do these panels run Flash scan? Thanks!

Hello my friend! That's cool!! About your Q's 1. It will depend if you have your panel always on with AC and DC power it should last a long time. 2 if you have backup power with Batteries 12v then your NVRAM battery should work fine! 3. Yes it used both protocols Flash Scan and CLIP! Stay safe and have fun!!! ...

@@lumenfirealarms awesome! Thanks man! One more thing. When you say batteries 12v, you mean both backup batteries are at 12v to get 24v backup power? Thanks for the help!

For each panel or power supply you will need two batteries 12v (7,12,18,26 or more Ah) that will be charger with 27 VDC from the battery terminal conector! Have fun!! ...

Hello thanks for watching, I took the factory training and when I passed they gave me the software and active license for 3 years! You should find for your nearest notifier distributor! Stay safe and have fun!! ...

Hola q tal! Nunca he utilizado ese comunicador q mencionas, tendría q investigar para poder darte una mejor respuesta, disculpa! Gracias por visitar q estes muy bien! ...

@@lumenfirealarms Gracias, ojala puedad guiarme un poco en eso. Estos viendo tus videos y son muy útiles la verdad. Gracias.

Hello I think so! But they are not critical you can use the panel for a demo system!! Have fun! ...

@@lumenfirealarms ok! There's an nfs-320 I am considering purchasing. The seller says that they are no troubles on it but the main board says PCB2 640. But the rest of the board says PCB 320? Is that normal? Thanks!

Yes it is!! They are really similar!! Have fun! ...

@@lumenfirealarms Thanks!

@@lumenfirealarms Hello! I hope you had a great Christmas! Can you program sounder, relay and isolater addresable smoke detector bases through the panels integrated keypad on an nfs-320? Thanks!

Hello I think you have a annunciator program but not connected, if you do have one make sure it's installed correctly if you don't have one then you need to change and remove it from the program. Stay safe and have fun! ...

Hello sure you should check the main panel so you can identify the system trouble event! Could be your batteries or just a fuse! Good luck! Stay safe and have fun! Hope you subscribe And check my other videos!! ...

@@lumenfirealarms i'll check when im on site, but thanks hope it works, i've subscribed n enjoy ur content

I appreciate thanks for watching I will keep making more videos! Stay safe and have fun! ...

Hello thanks for watching! Could you translate to English please! Have a nice day! Stay safe and have fun!! ...

Hello, make sure you check your configuration: ENABLE POWER SUPPLY CHARGER using VFT and check your battery connections and 15 amp fusible. Good luck stay safe and have fun! ....

Hello thanks for watching! You need to use verifire tools and check your settings about charger, check your fuse below the batteries terminal and check your batteries! Stay safe and have fun! You can look for me on Instagram to keep in touch! ...

Hello thanks for watching! Oh I recommend you to read the installation's manual, but if you have a HS-NCM-W damaged is really easy to replace it with a new one just make sure that is the same model! If you have Instagram you can follow me so we can talk more! @lumen fire alarms stay safe and have fun!! ...

Hello thanks for watching! You should use verifire tools and check the Enable Power Supply Charger setting! Check the fuse below the TB3 Battery connection! Stay safe and have fun! ...

Hello you need to use the verifire tools connect to the panel and upload the data base to your computer! Then after changing the battery you can download the data base back to the panel! Stay safe and have fun!! Thanks for watching!!! ...

@@lumenfirealarms could we use other brand heat and smoke detectors with notifier nfs-640 fire alarm system??

No, only if you use conventional spot detectors then you can install any brand using notifier monitor or zone modules. Stay safe and have fun!! ...

Hello my friend, you got trouble with a new card? What model? Which trouble? Stay safe and have fun! ...

Hello yes, the data base must be re-downloaded or all programming must be cleared and re entered you need to use verifire tools to do it, thanks for watching! Stay safe and have fun! ...

@@lumenfirealarms is verifier tools downloadable software sir.?

Hello, you need to get certified in order to get the software, you need to contact a notifier distributor that's the right way! Then they will give you access to the software! Stay safe and have fun! ...

Hello I will make a video about this very soon! Thanks for watching! Stay safe and have fun! Hope you subscribe! ...

Hello if you are using a network you need to check your NCM module and also your wiring! If you have a stand alone panel then maybe you configure something wrong! you can download the manual! And you need to check for the exact trouble!! Stay safe and have fun!!! ...

Hello how are you? Thanks for watching!! You need to check your LCM-320 SLC module! maybe it's damaged and remove wires and measure voltage!! I have a video about these SLC modules hope you can check out!! Stay safe and have fun!!! ...

Hello thanks for watching!! Well it will depend of the entire situation!! If none of your devices are communicating the you should check the SLC terminal without wires! Verify that you have all wires correctly coming from your CPU or previous LCM-320!! Stay safe and have fun!! ...

My panel is a NFS-320 but yes it is the same for a NFS2-640! Thanks for watching!! ...

Hello thanks for watching! You should write the trouble event ok your display! It could be your batteries low voltage or the 15 amp fuse! If you can get the installation and operation manuals you can read more about this! Stay safe and have fun! ...

Hey this trouble if for the NFS2-3030 you need to program your power supply AMPS-24 for supervision, need to connect loop and program! I will make a video about this really soon! Hope you check my other videos! Stay safe and have fun! ...

Hola que tal nunca me ha pasado este caso, bloqueada te refieres a que la pantalla está en blanco? Se quedó en la etapa de encendido? La pantalla te indica el estado pero no puede operar las teclas?? Ojalá me puedas comentar más y ver qué se puede lograr. Saludos gracias por tu visita! ...

El display me Muestra un mensaje: software no operativo. Sucedió al poner una base de datos versión 23 en una alarma versión 25. ¿Como pudo desbloquearla y como convertir la base de datos v23 en versión 25?

Hola que tal por favor agrégame en Instagram y poder platicar más sobre tu caso. Saludos

Hello thanks for watching!! I'm sorry I don't understand your comment! But I hope you liked the video! Stay safe and have fun!! ...

My panel is not working with battery supply. Only ac supply through work. I was replaced battery but battery not charge and not work through battery. Hows to solve this problem?

Hello I'm sorry I can't do that! You need to send a file from the owner to notifier with specific data from the panel. Look for a distributor in your city! Good luck! Stay safe and have fun!! ...

@@lumenfirealarms okey bro tx