Dana 60 carrier and pinion bearing replacement DIY

Подписаться 6 тыс.

Просмотров 31 тыс.

50% 1

I ruined my bearings! So it's time to replace them. I show you how to pull your carrier and pinion. Knock out the pinion races, pull the carrier bearings and press on new bearings. If you like this video please hit the thumbs up, if you want to see more videos like this please hit the subscribe button. Thanks for watching.
Consider buying me a coffee to help support this channel.
www.buymeacoffee.com/offroadfarm
Amazon affiliate links
GxL bearing puller
amzn.to/3cdFi8N
This puller is sometimes not available. If not then try this yukon puller I also linked to below. It is better quality as well
Yukon bearing puller
amzn.to/3dg1u3O
Follow me on Instagram @offroadfarm
Follow me on facebook @offroadfarm
Email me at offroadfarmchris@gmail.com
As an Amazon Associate I earn from qualifying purchases.

Авто/Мото

Опубликовано:

16 сен 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@paulsandock8789 4 года назад

Awesome job so far! Looking forward to the assembly process!

@Offroadfarm1 4 года назад

Thanks for watching, I'm working on the assembly video now

@tsmith578 10 дней назад

I have discovered that using a wrench for removing the carrier works pretty well, I used a wrench on one of the Ring Gear Bolts and turned the Carrier unit until the wrench is touching the differential housing, the I turned the pinion Yoke on the Carrier pushed itself out. Tried to remove it with two large pry bars before that and one of them slipped out of place Clunking Me Up Side My Head! 😮. No Fun!

@landoningram3561 4 года назад

Going to rebuild a dana 60 and 14 bolt using these vids for assistance. Thanks for the help!

@Offroadfarm1 4 года назад

Glad to help and thanks for watching!

@Icemedic24 4 года назад

Great videos, keep it up. I am in the process of doing a D60 and Ford 10.5" swap to my 2500HD. Going with 4:56 and ARB F/R and your videos have been helpful.

@Offroadfarm1 4 года назад

Glad you liked the video and thanks for watching. Good luck on your project!

@rkd350z Год назад

great video

@Offroadfarm1 Год назад

Glad you enjoyed it, thanks for watching!

@jasonmitchell4588 7 месяцев назад

Well done

@ReshardsAutomotiveWorkshop 4 года назад

Man... I need a tractor 😄. Thanks for the info.

@Offroadfarm1 4 года назад

It certainly does make moving heavy things around easier! Especially if you work by yourself a lot. Thanks for watching

@rubenurquiza8200 4 года назад

Great channel! More videos coming soon?

@Offroadfarm1 4 года назад

Thanks and yes, hopefully in the next few days

@brianhind6149 2 года назад

Great videos ; I don't understand how you ruined your bearings by running hot water through them......did you drive dirt in the hot water into them or what? Excuse my ignorance in this matter, but as long as the bearings were dried & lubricated I would have thought they would be fine. Thanks for great videos. Cheers! Brian Hind

@Offroadfarm1 2 года назад

Yes the axle tubes were full of dirt. After washing the axle the bearings were full of dirt/grit and did not turn very well. Technically I didn't ruin them since I didn't run them in that condition. I could have just removed them and washed them out well and just reused them. Since I had to pull the carrier and pinion, and since I was not sure when the last time these bearings were replaced I decided to replace them. Thanks for watching!

@kptheanimal6909 2 года назад

I can not find the bearings too mine any suggestions

@Offroadfarm1 2 года назад

www.offroaddesign.com/d60-differential-re-bearing-kit-includes-both-pinion-bearings-with-races-both-carrier-bearings-with-races-inner-axle-seals-pinion-seal-and-nut.html Thanks for watching

@mr_mmelk2230 3 года назад

What kind of lubricant is that?

@Offroadfarm1 3 года назад

That is 85w gear oil, I think it is lucas brand. Thanks for watching

@quentinraley8461 3 года назад

Just take the caps off and turn the pinion and it will push the ring gear and carrier out.

@Offroadfarm1 3 года назад

Thanks for the tip and thanks for watching

@Ry_Guy 3 года назад

That does not work.

@quentinraley8461 3 года назад

It does work because I've done it many times.

@Nightmare_the_xj 4 месяца назад

What year 60 is this?

@Offroadfarm1 4 месяца назад

Per the VIN 87 Thanks for watching!

@fullforce581 4 года назад

Do you have a name of the puller you purchased?

@Offroadfarm1 4 года назад

GXL Carrier & Pinion Bearing Puller Dana 30, 40, 60, 70, 80, Ford 10.25 Clamshell Design bought it off of amazon but it was sold by GXLPARTS

@fullforce581 4 года назад

@@Offroadfarm1 thanks. Do you know if it will do 14 bolt differentials as well

@Offroadfarm1 4 года назад

I have not tried it on my 14 bolt yet. But I did lend it to somebody to work on a Dana 80 and it worked for them just fine. If it works on an 80 it should work on a 14 bolt

@fullforce581 4 года назад

Alrighty. Sounds good hope it works. If not going to return thanks

@phantomwalker8251 3 года назад

you gota impact hammer.. turn diff upside down,, place decent bucket under,hit with impact. done. gravity wins..

@Offroadfarm1 3 года назад

Thanks for the tip, I may try that next time. Thanks for watching

@phantomwalker8251 3 года назад

if those bearings are that bad,they were bad before,,nothing to do with washing. its stationary,you can clean them in situ..hell i should do vids..

@Offroadfarm1 3 года назад

I thought about just cleaning and reusing them, but I decided to go ahead and replace them. Mostly because they are the most difficult and time consuming bearings in the axle to replace. Thanks for watching