EASILY Install Concealed Hinges / Comprehensive Guide / Euro Hinge / Cabinet Hinge / Vid

Подписаться 47 тыс.

Просмотров 78 тыс.

50% 1

Hi everyone!
Welcome to another video.
In this one I'm showing you all the processes to fit a full overlay concealed hinge. This hinge is the most commonly used hinge.
I run through all the measurements you need and do a demo from start to finish.
It's really easy, why not give it a go!
ALUMINIUM HINGE JIG - www.banggood.com/custlink/3vKEQHIQgd
GTV SOFT CLOSE HINGES - amzn.to/3UFdrGw
I hope you enjoy!
If you found this video helpful, please leave a like and a comment.
Enjoy The Video
Ryan
If you liked the video or have learnt somthing from it, please Subscribe and Share.
Also leave a comment :-)
I also have a Membership you can join to support the channel (Link below)
If you like my content & would like to support the channel monetarily you could become a youtube member with really cool PERKS!
/ @thelondoncraftsmanwor...
Or directly via paypal:
PayPal.me/TLcraftsman
****SPRAY ROOM TOOLS & MATERIALS****
GRACO 695 ULTRAMAX 2 AIRLESS SPRAYER - amzn.to/2O7HDJp
GRACO 390 PC AIRLESS SPRAYER - amzn.to/2LX0Ufw
GRACO RAC X GUARD - amzn.to/34tVFuo
GRACO 110 FINE FINISH LOW PRESSURE TIP - amzn.to/2PRrrvO
GRACO 310 FINE FINISH LOW PRESSURE TIP - amzn.to/2PIMQHC
GRACO 410 FINE FINISH LOW PRESSURE TIP - amzn.to/2spuWSd
SPRAY BOOTH TURNTABLE - amzn.to/35oNj8v
SIP SPACE HEATER - amzn.to/30ADvq9
SPRAY FILTERS ON A ROLL - amzn.to/2TyIlTz
TWIN SLOT SHELVING UPRIGHTS - amzn.to/2uTXapl
TWIN SLOT SHELVING BRACKETS 10 PACK (370MM) - amzn.to/38l76H2
PIPE INSULATION (TO PROTECT SHELVING BRACKETS) - amzn.to/2tjUK37
400MM ADJ SPEED EXTRACTOR FANS - amzn.to/2TCfBJK
****BANGGOOD TOOLS ****
UPGRADED PARALLEL GUIDES - www.banggood.com/custlink/GmD...
ADJUSTABLE TRACK SAW SQUARE - www.banggood.com/custlink/mKv...
HONGDUI CHAMFER PLANE - www.banggood.com/custlink/mDm...
200MM CARPENTERS SQUARE - www.banggood.com/custlink/33K...
300MM PRECISION SQUARE - www.banggood.com/custlink/m3m...
300MM ANGLE T SQUARE - www.banggood.com/custlink/vmK...
600mm ROOFING/CARPENTER SQAURE - www.banggood.com/custlink/D3K...
PAIR OF BESSEY COPY WRATCHET CLAMPS - www.banggood.com/custlink/K3G...
PLUS MORE...
ALUMINIUM HINGE JIG - www.banggood.com/custlink/3vKEQHIQgd
POCKET COMPASS - www.banggood.com/custlink/333...
DRAWER/DOOR HANDLE JIG - www.banggood.com/custlink/KKv...
DRAWER/DOOR HANDLE JIG - www.banggood.com/custlink/3vv...
GUIDE TRACK SAW SQUARE (BUDGET) - www.banggood.com/custlink/KK3...
ATOMSTACK LASER - www.banggood.com/custlink/mDG...
****TREND TOOLS****
SMALL FINGER PULL CUTTER - amzn.to/3GAMaAh
MEDIUM FINGER PULL CUTTER - amzn.to/3EqsMD6 (USED IN THIS VIDEO)
LARGE FINGER PULL CUTTER - amzn.to/3OmNZmf
TREND ROUTER TABLE - amzn.to/3TS7Omz
TREND T14 ROUTER - amzn.to/3hZDkl1
TREND T35 HOOVER - amzn.to/3V9Q3jn
****OTHER WORKSHOP TOOLS****
HYUNDAI HY55 COMPRESSOR - amzn.to/3PwujMm
VIRUTEX AG98F EDGER - amzn.to/3MbHroc
PAINTABLE EDGING - amzn.to/3EniuTK
PAIR OF BESSEY COPY WRATCHET CLAMPS - www.banggood.com/custlink/K3G...
T - TRACKS AS SHOWN ON MY ULTIMATE WORKBENCH - amzn.to/37WKIJd
1.6MM RADIUS - MICRO ROUND CUTTER FOR 1/4" ROUTER TRIMMER - amzn.to/3cTCYW6
MAKITA ROUTER TRIMMER - amzn.to/3JNENDp
SANDING DISCS - amzn.to/2FZe1JI
MAKITA ORBITAL SANDER - amzn.to/2TIkUqK
CTS HOSE KIT - amzn.to/3FCLXIL
MAKITA HOOVER - amzn.to/3cvNl3p
MAKITA CHOP SAW / MITRE SAW (LS1019L) - amzn.to/330BcCF
SCISSOR LIFT/CHOP SAW LIFT - amzn.to/3goeaI
MAKITA ROUTER TRIMMER( MUST HAVE!!! ) - amzn.to/3JNENDp
1/4" FLUTE CUTTER
1.6MM RADIUS - MICRO ROUND CUTTER FOR 1/4" ROUTER TRIMMER - amzn.to/3cTCYW6
JIGSAW - amzn.to/2R9z7em
POWER DRILL - amzn.to/2V2SGWT
MAKITA BELT SANDER - amzn.to/2UWDudW
BOSCH CHOP/MITRE SAW - amzn.to/3dUmyxl
MAKITA BRAD NAILER - amzn.to/2YOuiK0
MITRE FAST SPRAY GLUE - amzn.to/34pvYem
35MM HINGE CUTTER - amzn.to/2POJR09
SIP 10" TABLE SAW - amzn.to/2udA4JU
250mm TREND 48T BLADE - amzn.to/3aq2pgI
KETER FOLDING WORKBENCH (THIS IS A MUST BUY) - amzn.to/2NEWzyk
JOINTING COMPOUND FILLER - amzn.to/30AlVD2
ORBITAL SANDER SANDING DISCS ASSORTED - amzn.to/2FZe1JI
500MM GTV SIDE MOUNTED DRAWER RUNNERS - amzn.to/2sJ6YBU
MAKITA COMBI & IMPACT DRILL SET 18V - amzn.to/37qwNpi

Хобби

Опубликовано:

15 апр 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 86

@converdb 5 месяцев назад

Excellent video mate! I finally feel sure of myself to go install some of these bloody hinges 🙂 Glad to see new generations in the UK are regularly using metric system now

@thelondoncraftsmanworkshop 5 месяцев назад

Thank you... And I'm glad they helped ☺️

@kevinbenstock8116 8 месяцев назад

Brilliant video Ryan, you help us diyers with our home projects, passing on your experiance and knowledge, thanks a lot.

@thelondoncraftsmanworkshop 8 месяцев назад

Thank you! I'm happy it's helping! Thanks Ryan

@liamgibbons2117 3 месяца назад

This is very helpful, I wasn’t sure about the spacing on these concealed hinges however this is very simple and straight forward, thank you

@thelondoncraftsmanworkshop 3 месяца назад

Thank you!

@fetabrown 5 месяцев назад

Comprehensive and straightforward, keeping this one for future reference, ta!

@thelondoncraftsmanworkshop 5 месяцев назад

That's great 👍👍👍

@HeavyMetalisLaw Год назад

Hello, I've been binge watching your videos as my sis wants me to have a go of making her an alcove wardrobe, so thanks for all the information you upload. Regarding concealed hinges and the faker shaker style doors, are your doors 18mm MDF with a 6mm overlay, or 12mm with 6mm overlay. If 12mm, are there any problems caused when drilling the 35mm hinge hole? If 18mm, what hinges do you use to accomodate the 24mm total thickness?

@boskoapostolovic4188 6 месяцев назад

great video man, thank you!

@thelondoncraftsmanworkshop 6 месяцев назад

Great! You're welcome

@brianmoore47 Год назад

Great watch pal 👍 🔨

@hi-tech55 Год назад

Morning Ryan, another good video thanks. I am going to try using the same make hinge as what you do. I have been fitting these hinges for many years. I have a Kreg jig that does the job ok. Before that I made my own jig as you do. The problem I have is buying these hinges, some makes you buy the back plate separately to the hinge. I find it can get quite confusing, yes I know it’s me. However a refresher on the subject is always handy. Thanks again. Take care.

@thelondoncraftsmanworkshop Год назад

Hi Jerry, sorry for the late reply Thank you! I know what you mean. I like these hinges and they come as a whole( (Hinge and plate and covers) . I also like the large amount of adjustment in them too. I have the kreg, but when I got the veiko jig I stopped using it. Cheers ryan

@hi-tech55 Год назад

@@thelondoncraftsmanworkshop No worries. Thanks for your reply. Business must come first.

@thelondoncraftsmanworkshop Год назад

You're welcome, yes it's a bit busy atm. I hope you are well! Cheers 👍

@matty7758 2 месяца назад

Invaluable information. Thank you sir

@thelondoncraftsmanworkshop 2 месяца назад

Thank you very much!!! I appreciate it ☺️👍 Cheers Ryan

@kingjondalar4650 5 месяцев назад

Hi, I just started making some bedroom cabinets, I've bought a simple jig but now I'm confused about the hinges I need as there is so much choice on length's of products.... does the same jig fit most lengths?

@simoncrooks7441 11 месяцев назад

Thanks, good lesson

@thelondoncraftsmanworkshop 11 месяцев назад

Thanks 😁

@Mrbushy07 8 месяцев назад

Hi Ryan, recently found your channel as im about to embark on the wardrobes and cabinets for our home renovation. You have gave me yhe confidence and information i think to allow me to do a pretty good job. I must ask where you got your square with the holes from? Thanks again buddy

@thelondoncraftsmanworkshop 7 месяцев назад

Apologies, I think I got this one from amazon, I like the fact they have the holes in 1mm increments. I cant find the exact one but type in woodworking square and you should find one similar 👍 And good luck by the way, I'm glad the vids can be of some use 😊

@chrismansell2204 Год назад

Hi, I’ve got the same cutter after watching your videos…I’ve noticed you don’t twist lock your cutting guide into place. Not sure if you know that or not but it helps reduce any play. Thanks for the vids…they really help me out!

@thelondoncraftsmanworkshop Год назад

Hi, I didnt know you could do that. I looked at it and I can't see how that works, maybe it's a different model?

@JohnRoss-vq4bq 16 дней назад

can you please tell me where you got that square marking guide from Thank you

@thelondoncraftsmanworkshop 15 дней назад

Hi these arnet the exact ones but this is where I got them from www.banggood.com/custlink/DDKZ3fOekQ

@Marty-lv426 9 месяцев назад

Hi ryan ,say for example you make a 600mm by 600mm mdf cabinet would you just take off 3mm from each side of the door or is there a specific size your door has to be smaller than the unit.?

@thelondoncraftsmanworkshop 9 месяцев назад

Hi Marty sorry for the delay! Well if there is no panel or other door going either side of 'said' door, then no gap is needed on the sides. If it was one door sitting over/in front of a carass and the trims were stepped back (flush with carcass) then the door would be the same width as the carcass. Hopefully I understood your question correctly. cheers Ryan

@crochetqueenpl 7 месяцев назад

hi ryan, i was wondering if you predrilled holes into the face of the frame and if not why not? I am a beginner

@thelondoncraftsmanworkshop 7 месяцев назад

Hi, I generally don't predrill them, it gives the screws a better bite. They can be prefilled but only a small amount and with a 2 mm drill bit. But it's not essential

@jayjohal6892 26 дней назад

is it always 100mm from edges of the door no matter what size the door is?? Eg. big or small

@thelondoncraftsmanworkshop 23 дня назад

Well the top and bottom hing I always do 100mm, then divide up the rest equally. I full size door say 2400mm x 600mm would generally have 4 hinges, or 5 if you wanted to be sure to be sure...cheers Ryan

@jonathanbrazeau970 7 месяцев назад

how are you getting the 37mm #, from edge, for the placement of the baseplates?

@thelondoncraftsmanworkshop 7 месяцев назад

I close the hinge, make it square, and measure from the centre of the fixing holes to where the door would start 👍

@etafws Год назад

another great video - just a side note , there is a difference between an awl and bradawl , in the tip , i have both - the bradawl should have a chisel type flattened end. I used to always have bradawl, only recently got my self a couple of awls

@dugbert9 Год назад

I collect awls

@thelondoncraftsmanworkshop Год назад

Haha yes, I know that now 🤣 I called it a bradawl for years lol

@rubikasuto Год назад

Great video mate, i have the same jig and amazingly after a while the 2mm hole guide no longer line up, so its funny you mentioned it 😅

@thelondoncraftsmanworkshop Год назад

Thank you mate! Yes it's strange isn't it unless gtv have changed the spacings?

@rubikasuto Год назад

@@thelondoncraftsmanworkshop i only use Blum so not sure what has gone wrong 🙂

@thelondoncraftsmanworkshop Год назад

Yep who knows 🤣🤣 maybe can predrill new holes in that part of the jig 🤔

@juandenz2008 3 месяца назад

Good tutorial. I need to replace a Grass brand hinge that keeps unclipping. Looking at the catalogue is so confusing with all the different measurements. It seems like there is no direct replacement, so I hope they are somewhat compatible.

@thelondoncraftsmanworkshop 3 месяца назад

As long as you use the same type as you have, you should be able to use another brand or a newer type grass hinge. If in doubt, change all the hinges on that door, so they work in sync with each other, this should eliminate any doubt 👍

@bobbrock41 11 месяцев назад

Hello Ryan. Well done. Do you have a link for the little red marking square you used for the 37mm line on the frame?

@thelondoncraftsmanworkshop 8 месяцев назад

Hi sorry for the late reply, did you manage to find it?

@bobbrock41 8 месяцев назад

@@thelondoncraftsmanworkshop I did thanks, on Amazon

@RichDarbey 8 месяцев назад

Could you share a link as I would quite like to get one as well

@woodworking9605 25 дней назад

Great but marking is a bit trickier when the cabinet is already built.

@thelondoncraftsmanworkshop 23 дня назад

It is a bit trickier, but doable with the right technique :-)

@jefferyrobertson6623 3 месяца назад

Very helpful tutorial on full overlay hinge installation

@thelondoncraftsmanworkshop 3 месяца назад

Thank you! I'm glad it helped 😊 Ryan

@JoshuaWyborn 5 месяцев назад

how do you know from the edge of the door carcass that it's 37mm? or are they all that?

@thelondoncraftsmanworkshop 5 месяцев назад

Most of them are like that. You can put hibg on door, then put door up against carcass at a 90 degree to it, close the hinge so the plate part is touching the carcass and then measure from the front of carcass to centre of fixing holes. Make sure you put 3mm spacer in between door and carcass and that your plate on the hinge has been adjusted to center.

@JoshuaWyborn 5 месяцев назад

cheers legend! @@thelondoncraftsmanworkshop

@craigseddon5347 Год назад

Hi Ryan - where do you buy the GTV hardware from? Thanks 👍🏻

@thelondoncraftsmanworkshop Год назад

Hi I have put a link in the description just now for you :-)

@stevereed5776 Год назад

Nice video Ryan, my only comment would be that 99% of the time, you’d fit a door after the cabinet is built without the luxury of having the pieces lying side by side. Would have been better to see this. How much adjustment are there in the hinges?

@thelondoncraftsmanworkshop Год назад

It's all I had in the workshop at the time 👍

@Crapdraw1 7 месяцев назад

How do you know the distance from the edge ,, you are setting at 4 mm ...do different hinges req different distances ? How do you know ? Cheers

@raapstudy 5 месяцев назад

Can someone answer this question pls 🙏

@thelondoncraftsmanworkshop 5 месяцев назад

Well when you buy hinges such as blum or hafele brands, they can come with different thickness mounting plates (the part that gets fixed to the carcass , not door). So there are variations according to what door gaps you are looking to achieve. My general rule of thumb for the hinges I use(although they don't come with instructions) is a 4mm gap from the edge of thr door to the start of the 35mm Diameter hinge hole. This is what I usually start with and to be fair, 99% of the time is good for all 35mm hinges. You can always look up the specs of the hinge that you are using online, I'm sure you would find that measurement. Ryan

@LondonStuff. 4 месяца назад

What tool did you use to get the precise depth of the plate?

@thelondoncraftsmanworkshop 4 месяца назад

Im not really sure I understand the question

@pincermovement72 Год назад

What size are the hinges , I get confused with the sizes advertised 64, 110, 115 etc

@thelondoncraftsmanworkshop Год назад

Most common are 110 degrees, these are also 110 👍👍

@darshanpatel89 3 месяца назад

If door heights 1000mm(h) x 300mm(w) how many hinges need it?

@thelondoncraftsmanworkshop 3 месяца назад

2 will easily do the trick. But 3 if you want to, but not needed though.

@darshanpatel89 3 месяца назад

@@thelondoncraftsmanworkshop thanks Mate

@thelondoncraftsmanworkshop 3 месяца назад

You're welcome 👍

@sawdustwoodchips 11 месяцев назад

How do you fit 22mm doors to be overlay?

@thelondoncraftsmanworkshop 8 месяцев назад

Same technique, just make sure the hiniges you use allow for doors thicker than 18mm

@Martdes 4 месяца назад

How do you know if you need 3mm,4mm,5mm or 6mm? And how did you know it was 37mm high on the frame?

@thelondoncraftsmanworkshop 4 месяца назад

Hi I just worked it out, the 6mm works for me, 3mm is a little too tight. Close the hinge and place the door against frame along with a 3mm gap in between. That should give 37mm (if the hinge has been adjusted to centre) 👍

@Martdes 4 месяца назад

@thelondoncraftsman2026 just want to say thanks for making the video and kindly responding. Super appreciated.