EVERYTHING YOU NEED TO SWAP A 4L60E TO A 4L80E!!! 

Great video, keep your hands in your pocket 🤣 homie looks like he's conducting an orchestra.

My Silverado kills built 60s all day. 4l80e duel feed direct, AFL,TCC, and boost valve upgrade, accumulator delete with 3000 stall and your good

🔥🔥 like always

It’s that finger point and hand toss to the left that gets me every time-- New sub 😊

Looking good my Brother 👍 Happy New Years from Deep South Texas 956

Nice informative video keep up the great work 💯 thanks for leaving the links need to order the parts 💯👌

Love this truck 🔥💪🏽

Hey bro I was looking your video when you installed those long pipe headers, and I saw your headliner, I have a single cab covered on Grey suede, I would like to send it yo you, it would look good on the truck., where are you located? ??

You have a part number or link for that flexplate/spacer/bolt combo? Thanks.

Great video thanks

Will the crossmember work for a 4x4? I have a 08 gmc sierra with the transfer case just wondering if it will work or will I need a different cross member

I got my 6.0 n 4l80 in my garage cleaning em n shit. Yo vids cool n helpful

When you build this transmission for performance can it still pull things ?

What would u recommend I do to a 5.3 Silverado with a stage one cam ( I just bought it on thanksgiving )

What’s the link for the flex plate

Nice video. Would you do anything differently if you did it again? I have a 05 4x4 Yukon 5.3L. 233,000 miles. Looking to get a used cheap broken 4L60/65/70 to rebuild with my teen as a DIY learning project. To have ready. I found a used one for $60, with nothing but Reverse working. Thanks!

I’m following your build and about to do the same but 4wd. Keep it coming man

Nice 👍 Quick question. What would be a fun street combo for a a bit heavier extended cab truck. Say, cam, tq converter and rear end gears for an N/A 5.3/4l80 combo

Where did you get the bracket for the engine stand to hold the trans?

You ever gonna relocate the shifter to the floor? I wanna do it to my 4l60e but literally have no idea what to do other than get the shift kit i want

Idk why you got comments abiut the hands, i didnt even notice em 😂 keep up the good work very informative

wat stall do u recommend for (6.0 stage 2 cam, long tubes)

so i have a lq9 6.0 would you hapen to have a link to the proper flex plate ?

Awesom setup what drop is that thanks??

Can I used the stock driveshaft or will I need to change it ?

Did you have any problems once you put the turbo in to run crossover pipe with the 4L80

Hopefully that flex plate is sfi or your gonna snap it when you boost it! but great job dude keep it up

Do I need the fly wheel spacer for my Lq9 engine

Someone help me out I did a 6.0 and 4l80 on my 03 gmc but the truck stalls with I put it on drive if someone know something lmk

I wanna do the same swap but can it be done with a 4.8 engine??

Hey what dipstick tube did you use

Any idea if it's 4x4 will 4l60e transfer case swap right to 4l80e

you won’t be using a different yoke or replacing the u joint?

What shifter linkage did you use bro ?

Would it be the same parts needed for 4x4?

i have an 02 suburban and need a new tranny. any idea which i should get?

So I could reuse my stock driveshaft for the 4l60? And could I reuse my torque converter?

So im at risk of having my driveshaft exploding if i remove my speed limiter?

Good info, my 4L65E is not liking my 2 step. 👍

do you think all of this applies to an 04 Denali Yukon?

Did you have to reflash the computer for it

What do i need for a driveshaft

This is exactly what info that I was looking for thanks

How much you spend in total total

You bought it off Ebay right lol that's gotta be the same one I was looking at.

Is this the same for a 06 crew cab??? lol

what dipstick did you use ? part number or link ?

Video starts @4:39 ✅

Have 2 of them. 500$ each One is a GM Goodwrench reman

Take the 4l60 and find a stock 4.8 with some ring gap and a lil turbski and maybe drop it in something small, Itll give the 4Llimpy a little longer chance to survive being in a lighter car lol

Ill buy that 4l60

"you pay what you get for" lolol

Is your motor stock?

Sounds louder now

Asking for myself 😂😂 they have anymore 4l80’s for sale….. seriously 🤔

The 4L80 is more sturdy than a 4L60 but l'm not a fan of the 2.48 1st gear ratio of the 4L80 the 3.06 1st gear in the 4L60 is better and if you throw a 6L80 in the mix it has a super low 4.03 1st gear whats the big deal well with a 6L80 trans with a 3.27 - 3.42 rear end gearing will leave from a dead stop as well as a 4L80 trans would with 4.30 rear gears and not only that but in 6th gear with a 6L80 trans and 3.27 - 3.42 rear gear will be much more pleasant and peaceful to drive on the highway at 80mph than 4.10 - 4.30 gearing would be in a 4L80 trans the difference at 80mph would be 2100 -2300 rpm with a 6L80 trans with 3.27 - 3.42 rear gearing and with a 4L80 trans with 4.10 - 4.30 rear gearing 2900 - 3200 rpm if both had lockup torque converters

I usually repin my own harness for free

just FYI you don't even have to rebuild a 4l80 for boost. a buddy of mine has a 4l80 in his drag truck that's making 1200 to the wheel with a 9.3 quarter mile time and all he has is a shift kit. although if you have more money to spare in not saying don't rebuild it but if you don't got the money you don't need to do that.

You pay what you get for... 😂

Any one saw the fire coming out of the hood

Sell me that 4l60 tho

I never understood why everyone wants to 4l80 swap, I'll take a built 4l60 over a built 4l80 any day.

“Yeah uh hey bro could you stop doing a natural human gesture when you’re talking and filming content for us to watch for free?” Lmao all the comments telling dude to not talk with his hands. Shut up and just watch the videos 🙄

Great video with good content but please bro stop talking with your hands. It is distracting to see you making the same hand gestures over and over. Keep up the good work on the truck.