Extrusion problems

Подписаться 13 тыс.

Просмотров 354 тыс.

50% 1

Videos that might interest you:
Retraction Calibration • Retraction Calibration
Cura 3 - How To Examples • Cura 3 - How To Examples
How To Dismantle The Hot End • How To Dismantle The H...
Top 5 Features Cura 3.2 • Top 5 Features Cura 3.2
How to Clean a 3D Printer Nozzle • How to Clean a 3D Prin...
Cura Time Saver Setting • Cura Time Saver Setting
In this video, we will look at the different extrusions rate problems. You can have over extrusion and under extrusion or just the right amount.
So I will show you the look of something that is over extruded, correct extrusion and under extrusion. You will see an example of each. And how to recognize this problem.
Then I will demonstrate how to measure the extrusion rate of your 3D printer, with a simple technic, and a direct way to calculate the percentage of correction needed.
And finally a quick word on how to adjust the rate the easily.
My gear :
Amazon US (Commissions Earned):
Filament used PETG MG Chemicals amzn.to/2gWBJdn... 3D Printer model 3DP-11-ATL amzn.to/2yF9FEY
3D Printer Monoprice Select Mini V2 amzn.to/2yK9TdV
Camera Sony A6300 amzn.to/2gWmaTi
Sigma Lens 30mm F1.4 amzn.to/2gtzeyL
Neewer 7" Field Monitor amzn.to/2gWAsD7
Neewer Accessories amzn.to/2xcYobL
SanDisk Extreme 64GB SDXC UHS-I Card amzn.to/2yF34di
Manfrotto Compact Tripod amzn.to/2yEIZnv
IMDEN Omnidirectional Condenser Lavalier Microphone amzn.to/2xcY4cR
Amazon Canada (Commissions Earned):
Filament used PETG MG Chemicals amzn.to/2xdKo1v
3D Printer model 3DP-11-ATL amzn.to/2xdgyKq
3D Printer Monoprice Select Mini V2 amzn.to/2yKAUhn
Camera Sony A6300 Kit amzn.to/2gVrhD4
Sigma Lens 30mm F1.4 amzn.to/2xWO2kJ
Neewer 7" Field Monitor amzn.to/2zqL97K
Neewer Accessories amzn.to/2gVrshI
SanDisk Extreme 64GB SDXC UHS-I Card amzn.to/2gVrw0W
Manfrotto Compact Tripod amzn.to/2xVgChk
IMDEN Omnidirectional Condenser Lavalier Microphone amzn.to/2xX4lOs
Hi, I'm Frank my channel is all about 3D printing. I can't get enough of my 3D printer. I make everything and anything out of 3D filament (PLA, PETG and more). As I say a printer that is not printing is a missed opportunity.
I'll be doing electronics, mechanics, computer engineering, DIY, reviews and tutorials.
I update twice a week on Tuesday and Saturdays.
Subscribe to my channel, and don't forget to turn on notifications.
You can also find me on :
Facebook: / franks-3d-shop-5670064...
Twitter: / franks3dshop
Instagram: / franks3dshop

Наука

Опубликовано:

23 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 212

@daveharkin4731 5 лет назад

good quality video, but I think you could have given a little more information and demonstrated how you actually calibrated your machine. Now I have to go somewhere else to get the information that I need. I'm not trolling you but hope you accept this as helpful criticism so you can make more informative videos in the future. Respect

@minikkarga7776 4 года назад

@patrickbodine6010 4 года назад

Yes.

@GoreGirlFX 4 года назад

Agreed.

@Peter_Parker69 3 года назад

To be fair. That depends on the machine and slicer anyway. He showed how to find the problem, now it's up to us to continue our own research.

@floatingchimney 3 года назад

@Dave Harkin, You do know there are about 150 different 3D printers with about 50 different operating systems on them?

@BlackDragonBE 5 лет назад

This is one of the best videos about extrusion out there! It's short, to the point, has examples and provides a solution. You got yourself a new subscriber!

@Franks3Dshop 5 лет назад

Thanks! Now need to make time for new videos, so many projects :-)

@noahlee1785 2 месяца назад

Where has this video been all my life, my printers been out of commission for nearly 6 months simply because nothing I tried worked I even replaced my entire print head, apparently my printer was having horrible horrible under extrusion with it only putting out 25% of what it was supposed to, fantastic video I’m surprised this never showed up when I searched my problems.

@littleraptor9898 4 года назад

iam new to 3D printing, and i was surprised i got it perfect first try! it is not exactly "perfect perfect" but iam happy with it. soooo many ideas trapped in my mind for 2 years are prone to become true!

@barrywilliams2008 5 лет назад

Cheers frank been having headaches over this blob issue for about a week now my flow rate in cura was 100% that was way over extruding infact i had to half it to 50% thanks for the help bud finally i can get back on to some nice models again

@christophercola Год назад

Thanks for making it a super short video! I hate it when channels make it 20 minutes long to explain something simple

@DustinBecker8606 Месяц назад

Quit, easy, to the point, and extremely useful

@sejlefrew 5 лет назад

thumbs'd up because you provided examples, just what i needed to pin down a problem

@donkeykong3x3 6 лет назад

One quick problem I found with the instructions is that you can't use the difference to find the percentage for correction. At smaller numbers it will be relatively close, but quickly escalates. You should divide the amount you told it to extrude by the actual amount extruded. In your case 100/96 gives 104.166%. This isn't much difference, but at 90 out of 100 the error is 1% (111% vs. 110%), and 80 out of 100 the error is 5% (125% vs. 120%).

@Franks3Dshop 6 лет назад

You are right, but it is simplier that way, you just do it a couple of time and your good, +- 2mm on 100mm extrusion will not affect significantly the prints, you could always be more precise the way you describe.Thanks!

@jairhausheer3712 8 месяцев назад

Came here to say this, but not quite as elegantly

@jasontritz7777 2 года назад

First actually helpful video on correcting my under extrusion problem

@DFDuck55 6 лет назад

I don't have a 3D printer yet, but planning to get one soon. I will store this helpful bit of information away in the mental bank, I'm sure it will come in handy. Thank you.

@Franks3Dshop 6 лет назад

Stay tuned, I have a bunch more of those tips!

@raptordragneel6978 6 лет назад

Nice now I need a 3D printer already have so many ideas

@Franks3Dshop 6 лет назад

+Raptor Dragneel You can send me some of you want 😀

@bluebikegarage 11 месяцев назад

Thanks for the quick instructions, helped me a lot!

@snixn3155 4 года назад

You my guy are my savior I was having quality problems on the anet a8 ( not the best printer I know but it’s my first one) and this fixed it

@Franks3Dshop 4 года назад

Thank you :-)

@isaackershnerART 3 года назад

Thank you! i just attempted this and found out i was 1cm short for every 10 cm! This could be related to a bigger issue with either the extruder or bowden system but this should help for now! just trying to keep my ender 3 pro alive for a little longer. got a direct drive CR10 and now I want another one :D

@daveyJ213 2 года назад

Dude! I am a total newbie. You're not going to walk me through the calibration. C' on, Man!

@matesinku8272 2 года назад

Thnx Frank, for the quick explanation

@sarceneaux6989 2 года назад

Old video but thank you! Helped me out.

@feuerstormA6 4 года назад

Wow you show this so simple and easy! Good video!

@CristalianaIvor 5 лет назад

Interesting. I will try this and hopefully it fixes my problem.

@volyknx5504 6 лет назад

Nice video Frank, i dont know why i wach these kind of videos but it is interesting.

@Franks3Dshop 6 лет назад

+Volyk Nx I did also, than got a printer, and that changed everything! So easy to think of something, designed, print, tweak the design, reprint. It is so rewarding.

@jpgamingdiyetimprimante3d456 6 лет назад

it is always good to learn something ^^

@TomTech24 5 месяцев назад

Merci pour tes conseils. Yess

@thinnspeaker6123 4 года назад

The intro is dope

@Jan6750 7 месяцев назад

I'm a clueless bambu lab X1C owner....but I'm learning. (Maybe a "push & go" machine isn't the best way to learn). What I got from this vid is what under/ over extrusion looks like! 👍 Thanks.🙏 My Lab printed 2 good prints, but now the extruder box keeps bashing the front door, (knocking the front cover off and telling me the cutter is stuck, but it isn't), laying shadow first layers in the corners or edge of the plate and over extruding. All the self calibrations change nothing. I've serviced the belts and now can try adjusting the flow rates in the right direction. Fun nightmare.😳

@AnimalStomper 4 года назад

Thanks for the tips!

@michelevitarelli 4 года назад

Great video. Thanks for sharing.

@thecricketandgolfchannel4766 2 года назад

works incredibly well

@danielnemeth515 11 месяцев назад

Thank you!

@prince_m_h_d2513 2 года назад

I finaly solved my problem

@JohnSmith-un9fy 4 года назад

Fortunately I own a Trinus printer that has never had any extrusion issues there are no settings for this on the machine. It is small and limited on print size but I have ran the crap out of it for two years. I have only had to replace the nozzle once. It does not fail much either. Looking forward the arrival of my CR10s

@pmgear 6 лет назад

THanks! Got to check my A8 now!

@danielro1209 Год назад

You are mixing E-Steps and flow rate

@yerligurbetci4295 5 лет назад

The intro got me to instantly subscribe

@tylertempler6205 6 лет назад

Thanks man you are awesome! Totally fixed my issue!

@customsrusprincalifornia2284 3 года назад

The question is how to change the flow rate ? The rest of the video is great.

@Franks3Dshop 3 года назад

Hi, it depends on your printer interface, it can be done in Marlin if you configure it yourself, or in the interface, or even in the slicer if you have other choices.

@MrIsraelParent 2 года назад

I think there’s a market out here for good, French content.. ;)

@skrewdriven6891 2 года назад

VERY good tip

@minhthanh5206 4 года назад

Thanks you so much.

@irjayjay 6 лет назад

Really nice video, really informative, please keep them coming, subbed!

@Franks3Dshop 6 лет назад

Thank you, I am in production right now :-)

@StalkedByLosers 8 месяцев назад

Can you do some video about tip temperature and some possible failures around that?

@sebastianhustad4176 3 года назад

Thanks man

@strato_5459 4 года назад

what if my prints are perfect bottom or near perfect, with perfect sides but the top seems like its over extruding? like it has deep ripples in the top. could this be from the nozzle hitting the surface? sometimes when it goes from one end to the other it will almost drag a little over the surface and leave a line where it went. what could be the issue?

@Kriswixx 4 года назад

subbed. love the simplcity of the explaination and your intro is boss. Diggit subbed and belled.

@bebedasilva9700 3 года назад

Flow rate! thank you

@iudexe3103 6 лет назад

Man, I wish I have a 3d printer 😖 Anyway, nice video frank 😀

@Franks3Dshop 6 лет назад

When you will have one, you will know everything about it :-) And many ideas on what to print !

@shaunwhiteley3544 6 лет назад

Thanks, very helpful, quick question on when you showed the 3 different models, what percentage were they over and under extruded? 5, 10 percent? Cheers

@Franks3Dshop 6 лет назад

Hi, If I remember correctly, I went about 75% over and under just to be sure to see clearly the effect...

@ganeshbhatkar1151 5 лет назад

hello frank nice video i have some problem with my extrusion i have made my own printer using scrap and proper electronics my extrusion motor get back and forth when i am extruding my filament and same for printing too but i need to solve these problem please help me

@Franks3Dshop 5 лет назад

Hi, what is the problem exactly? Do you have a partial clog?

@MaacAbra 5 месяцев назад

Cool! 👍😊

@callsignprofessor 3 года назад

Nice trick, thanks!

@threedeeprince 6 лет назад

This helps a lot. A lot of my prints start to look like the over extrusion sample. My nozzle drags on the print and even broke the hot end heat brake. I do have a question though, if my prints still look like they are over extruded (after it prints all 100mm of filament) is there any other steps I can take to make it look normal?

@Franks3Dshop 6 лет назад

Hi, I would say the you have to make sure that your nozzle size in your slicer correspond to the nozzle you have. Also if you drilled your nozzle to unclog it or if you have printed material with particles like wood filament or glow in the dark, your nozzle could be larger now, so you would need to replace it. And if you plan to print those types of filaments, change for a stainless nozzle.

@threedeeprince 6 лет назад

Frank's 3D shop thank you so much. That’s very helpful

@bowl1820 Месяц назад

Note: He Measured up 12 CENTIMETERS and marked it. Then extruded 100 MILLIMETERS. Then measured 2.4 ??? (CENTIMETERS). Then came up with 96 MILLIMETERS It would simpler to just use Millimeters for all measurements and not have to convert units. Measure 120mm Extrude 100 mm Measure 24 mm 120mm - 24mm = 96mm A 4mm difference = 4%

@rajualbeena 5 лет назад

11th of December I purchase tronxy x5st-2e printer. I calibrate the extruder it's 106% I use cura 3.5 . But print is so under extrude .4mm nozzle .2 layer 106% flow. I increas the flow rate at every print . But print is under extruded every time. I found not good but ok flow rate at 500. My cr10s flow rate is 104 and it's perfect.

@Franks3Dshop 5 лет назад

First I assume you do not have a partial clogging, do a couple of cold pull to clean up the nozzle if you are not sure. And verify that the filament size is correct in Cura and in the Tronxy with gcode ‘M404 W1.75’ if it’s 1.75mm and ‘M200 D0’ will revert back to linear extrusion instead of volumetric extrusion. After that issue a ‘M500’ to save everything.

@camillesuchet4602 5 лет назад

Thx !

@SamTheEnglishTeacher 5 лет назад

I had a 24mm remainder (so same result as this video) however my cube test print looks like the middle one. Do I have a problem? :-/

@Franks3Dshop 5 лет назад

Hi, the part will be a little less strong, I always make sure it’s correctly calibrated, 1mm less over 100 is just right it prevents having stringing.

@proto_hexagon5649 2 года назад

nice. but next time put example like what parameter need to be changed. wich in this case steps/mm.

@blaze6134 5 лет назад

you remind me of my high school math teacher, he also was not good at explaining the finer details

@julzrtw 6 лет назад

Hey Frank, I learning about 3d printing. But I am curious, do you also mess and with CNC machine/manual lathes?

@Franks3Dshop 6 лет назад

+Julz Prez Yes I do use the CNC and will incorporate it in futur videos. I do not have a lathe but would love to have one and learn to use it, my step father had one, I was watching him use it, it’s fascinating.

@julzrtw 6 лет назад

+Frank's 3D shop, awesome! The reason I ask is my dad had been a machinist my entire life. CNC and manual. And I'm interested in learning and seeing what you can make from them. 😁👍🏼

@wokey83 5 лет назад

thanks mate a++ tips

@christinoccs 5 лет назад

THANKS for your videos, I have a trouble with my 3DP Im using slic3r and repetier, in some occasions, my impresions start 10 or 20mm high Zaxis, can you tell me why is that

@Franks3Dshop 5 лет назад

Maybe you are missing a home axis G28 on some profiles?

@christinoccs 5 лет назад

I have a QU BD three Up, when I connect Z axis switch it does not work correctly, so I decided do not connect it, where can I find the gcode start end ?

@Franks3Dshop 5 лет назад

I would try Cura with a printer profile resembling your printer, maybe your Z switch is reversed in the code, is it an home made machine or an old kit maybe?

@christinoccs 5 лет назад

home made, Im starting in this 3d world, I dont know very well the software and language, I had 1 month assemblying it, yesterday I printed my first model in PLA but I had to raised the temperature to 245 because it did not extrusioned very well

@Franks3Dshop 5 лет назад

I never used a ramps board myself, but first thing for the heating, you have to select the correct thermistor type, I know how to do it in Marlin but not in repetier, I suspect that you do not have the correct setup or it is not connect correctly. You could verify with an infrared thermometer if your temperature readings are correct. For the Z Axis, again in Marlin you can inverse the logic.

@pratyushsaxena9343 4 года назад

You are super sir

@ImKurtzy 2 года назад

i did a XYZ test cube and the bottom layer is meh and then the layers right above it are perfect then it goes back to bad for some layers then good again near the top, then meh again at the top surface... I dont know what this means at all

@hippopotamus86 4 года назад

I have an Ender 3 pro. I calibrated the E-Steps so now 100mm extrudes dead on 100mm. I have flow rate set to 100% in Ultimaker Cura. I measured the filament and it's exactly 1.75mm measured multiple times in multiple places. The printer is brand new, nozzle is not blocked, and is 0.4mm. The settings in Ultimaker Cura are correct. Why does it still over extrude? I have had to set the flow rate to 90% but still the prints are over extruding. at 85%, it under extrudes. If all the math is correct, it shouldn't be over extruding right?

@Franks3Dshop 4 года назад

Your Nozzle could be out of specs not 0.4mm anymore or was never. If you print wood filament or glow in the dark for exemple, it would enlarge a brass nozzle pretty quickly say 200 grams fo filament...

@funkycowie 6 лет назад

My 3D printer does not give me access to the filament to be able to mark it as it goes through a bowden tube, etc. Is there another way of doing this?

@Franks3Dshop 6 лет назад

You can do it just before it enters the Bowden tube before or after the extruder gear. You have to measure the length going to the hot end... if you can remove the Bowden tube, you could measure the filament coming out the extruder.

@funkycowie 6 лет назад

Thanks, but I just did a temperature tower but instead of adjusting the gcode for temperature I adjusted the flow then I have picked the right one :) Less scientific but it works ;)

@ShadowtheWiseman 5 лет назад

@@funkycowie What printer are you using? You should provide that modified file for others to test their printers, it was quite ingenious.

@funkycowie 5 лет назад

@@ShadowtheWiseman There is no point sharing the .gcode file as everyone's printer will not be the same regardless of brand etc. I just used Cura to modify the gcode only which you need to do to do a temp tower, I did not adjust the .stl but feel free to create a new model with flow percentages on.

@mic3l Год назад

cool

@joseantonioreyna 6 лет назад

hello, so my flow rate according your example should end at 104%? thanks

@Franks3Dshop 6 лет назад

Yes if you want to do it in your slicer. I prefer to issue a M503 command using Printrun (or Pronterface, you can listen to my video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YpWCKNagjuI.html to help using that software) connected via USB to the printer, look for the M92 line and the E97 (in my case it was 97 initially on the monoprice mini) add or subtract the percentage of error to that value. Issue a: M92 E100 M500 And do the same test again and see if you still get an error, until you are satisfied with the result. I presume here that you do not have a clog or results will be way off. My printer ended with a value of M92 E111 which is 14% more than the original. Does it make sense to you?

@sudovkin 6 лет назад

Thanks Frank! I have a question: why 12 cm? I did mesurments like you, you have 2.4cm I have 7.0cm...if I understood correctly I have underextrusion, by 9%?

@Franks3Dshop 6 лет назад

Hi, I will have to look at that video again it’s too late right now, but I think you get the idea, you extrude X amount (100mm is easy for calculating) and measure how much was taken. Than if the printer only took 90mm you know you are missing 10mm out of 100mm so it’s 10% under extrusion. Same thing if the printer took more than 100mm but it’s over extrusion that time. Does it answer your question?

@sudovkin 6 лет назад

Yap, thank you!

@elidari60 4 года назад

If you do not have a printer that have note automatic Extrusion for 120 mm how do I set it up my printer is anycube I3

@Franks3Dshop 4 года назад

You can use pronterface so that you can connect your printer via USB and control it like extruding 100mm of filament.

@roadstar499 4 года назад

I have a question that i need answered by an expert.... If i slice a model and its was done telling slicer to use a .06 nozzle and later on switch to a .04 nozzel will print fail do to extruding to much filament etc??? can this cause ringing etc of maybe cause extactor to start clicking /jamming??? i am having these issues i think... thanks

@Franks3Dshop 4 года назад

Hi, it's all possible yes, if the extruder is not strong enough to push the filament at the rate of a 0.6mm nozzle, it will skip steps and that would result in an under extruded print that would be fragile possibly with gaps and blobs.

@roadstar499 4 года назад

@@Franks3Dshop thax... turned out it was more hot end clogging than extruder issues this time...i have gotten much better at pin pointing 3d problems over last couple of months.

@Franks3Dshop 4 года назад

For reference with black PLA after a week of printing about 20h a day, I replace the nozzle before it clogs and clean it at a later date.

@EditOnRel3ase 4 месяца назад

Did that pla coffee taste good?

@Franks3Dshop 4 месяца назад

It didn’t have any special taste, keep in mind that you should use food grade PLA and also some food grade varnish to prevent bacterias in between the layer lines.

@Reds3DPrinting Год назад

man i wish someone could help me.. my walls look great but i am over extruding my inner layers like crazy.. idk what to do im about to give up and thats not like me.. im just so burnt out

@shizzle1994 5 лет назад

So my monoprice mini select v2 has just randomly got the under extrusion issue when i switched to black im now trying a different color i hope it works any help would be appreciated again it is under extruding... now with all my pla

@Franks3Dshop 5 лет назад

It probably is partially clogged, if it is extruding with a little bend on the first millimetre, it probably is, I have some videos on of to clear a clog called a cold pull, ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-8zsV_FN-y4o.html you can also do it with the hot end in place, and just remove the teflon tube entering the hot end, push the blue plastic ring to pull it out, or unscrew the brass fitting.

@gates6172 3 года назад

Bonjour Frank's, j'aurais une petite question a propos d'un insert que je veux introduire dans ma pièce a imprimer. comment puis-je te contacter?

@Franks3Dshop 3 года назад

Salut, désolé pour le retard je peux être contacté à franks3dshop@gmail.com

@voldy3565 3 года назад

Is it OK if I'm overextruding by 1mm?

@Franks3Dshop 3 года назад

Should not be a problem, you could get some strigning, I like to keep it about 1mm less not over.

@SamWanderlust 4 года назад

Never correct the extrusion using the slicer flow rate !! Correct the extrusion on the extrudeur step parameter of the printer !

@Franks3Dshop 4 года назад

Yes it's better, both works.

@lomeranger 5 лет назад

I only got 40mm after having it extrude 100mm. I then tried taking the bowden tube off, same. Any ideas?

@Franks3Dshop 5 лет назад

Could be a partial clog, do the extruder motor gears grind the filament?

@navidmehdi6 Год назад

this is really fustrating most of my prints are failing.

@UAVwaffle 5 лет назад

on my ender 3 I get under extrusion on the back right corner of the print bed. I checked all the hardware and I can confirm it has something to do with the gcode not the printer. I am using cura 3.5 . when I use the default print file it is fine it only happens with cura gcode

@Franks3Dshop 5 лет назад

Humm do not see why Cura would do that, maybe be if it’s jamming or rubbing in the ptfe tube at certain angles? Try to print only in the front opposite corner, if it still does under extrusion it’s Cura, if not it’s something physical on the printer. Maybe as to do with layer height, try 0.2mm with 0.3 first layer

@UAVwaffle 5 лет назад

@@Franks3Dshop i was messing with my printer earlier and I noticed if I extrude only .1mm it jumps back (the filament does not slip the entire gear and filament skips back) but if I extrude 1mm or more it extrudes normally.

@Franks3Dshop 5 лет назад

Hi, I would verify that the tube is seated correctly at both ends and in the hot end...

@ArcanePath360 5 лет назад

Having the same issue with my Geetech A10M which is an Ender3 clone with dual extrusion. Cura 3.5 also. It seems to do weird things with infill, missing sections out while massively under extruding. It also prints strangely, where it would end on a layer, then travel all the way to the other side of the print and start the next layer from there. I've not used Marlin before so maybe I'm just not used to the print method.

@Franks3Dshop 5 лет назад

There is a setting Cura to optimize the print order

@micpep 3 года назад

C'est pas pire! Ça indique si la gear pousse à la vitesse voulue. J'y avais pas pensé à celle la. Mais ça compense pas pour la variation du diamètre du filament... Disons 1.75mm +/- .02. À 1.73 ça donne une surface de 2.35mm carré. À 1.77 ça donne 2.46... 2.46/2.35=1.047. C'est presque 5% de variation possible avec des tolérances très correctes. Je te laisse faire un autre video pour les anglais. Tu fais bien ça.

@dean-porter 6 лет назад

Hi Frank, do you have a link to the model you used?

@Franks3Dshop 6 лет назад

Hi, you can use any plain test cube and resize it in Cura to what you like: www.thingiverse.com/thing:281334

@ArcanePath360 4 года назад

My e-steps were extruding 78mm when I extruded 100mm in the firmware. What's odd is that my flow rate is at 90% while printing because it's over extruding. I also have a dual extruder but the firmware only lets me adjust one.

@Franks3Dshop 4 года назад

Hi, verify your nozzle size in your slicer maybe it’s that.

@ArcanePath360 4 года назад

@@Franks3Dshop Nope. Cura says 0.4mm with 1.75 filament. When I adjust my extruder to extrude 100mm it massively over extrudes, so I set back to factory settings to get it near right on the flow, between 90-98% while it's printing. If I leave at 100% it seems fine until about 2 inches high and then it's grinding on the previous layer more and more until I reduce the flow. I've checked my Z steps and they are spot on so it must be extrusion.

@Franks3Dshop 4 года назад

I would verify your Z movements, seems to me that there is an error that accumulates layer after layer as if your Z steps/mm were off... Take a ruler and measure the movement to see if it’s accurate.

@ArcanePath360 4 года назад

@@Franks3Dshop I have. I set it to a 100mm height and measured with a digital ruler and it read 100.0mm on the nose. I thought it was this too, but unless my ruler is off it seems to be not the case. It's weird because it doesn't look like it's over extruding, the layers don't have artifacts, blobbing or anything other than visible lines, which I think was my frame screws being slightly loose underneath and I've now tightened up. Unless this is what was causing the grinding while the carriage was wobbling as it got higher... I do have two spools sitting on top my frame and there was wobble before I found the loose screws. Maybe it was just that. I won't know until I do another tall print. But reducing the flow rate down to 90% and there being no gaps in the print when it still had about 8 hours to go doesn't make sense. I just realized something else though... I had turned the printer off half way though the print and used the resume function the next day. I wonder if it tried printing the last layer again and the extra extrusion had a cumulative effect? Thanks for the feedback.

@prabhugoudabiradar2232 6 лет назад

It's cool video.Sir make video on "how to make RU-vid channel and explain all procedure". I can find in RU-vid sir but, I want you to explain sir( kind request).

@jimmyfavereau 6 лет назад

Step# 1. Bring on the coffee. :D. Merci!

@Franks3Dshop 6 лет назад

De rien!

@joaonunes1313 5 лет назад

Hi, anyone with anet a8 can help me? I have an anet 8 and when this is printed after a 5 layers begins to divert the layers to the side. Some advice?

@Franks3Dshop 5 лет назад

Hi, when you get layer shifts, something is skipping, it can be the belts that are loose, the motor current is too low, the bed is not level so the hot end bumps agains the already printed part. You can use Z-Hop in your slicer to help prevent the later. Let me know if it helps.

@joaonunes1313 5 лет назад

@@Franks3Dshop How can I adjust the filament output, the parts that have already been printed have little filament are very fragile

@Franks3Dshop 5 лет назад

It could be that you have a partial clog that limits the quantity of plastic coming out of the nozzle, what I do in those case is a cold pull like in this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-8zsV_FN-y4o.html or this one ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hBkTeXxcFi8.html

@ReudigaDeOfficial 4 года назад

And now? I dont know where to setup that failure :(

@Dave45784 22 дня назад

I think I'm getting over extrusion on my printer :-(

@munki2992 10 месяцев назад

I marked 12cm. Extruded 100 mm and ended with 8.5cm🙏🏽helpppp

@makewithmegma 3 года назад

🔥💕👌👍

@figuresix Год назад

To bad my printer dont give me option to extrude filament percentage.

@TheBookaroo Год назад

Hi, you can also do it in your slicer settings…

@habag1112 Год назад

"Extruding filament percentage" is usually called "flowrate" or just "flow" (If you're using CURA, the setting is in the material tab). 1. You should calibrate your e-steps first. Changing the flowrate is just slapping a band-aid onto a problem that can easily be fixed permanently. 2. Usually, you set the flowrate percentage in your slicer, not on the printer. 3. Some firmwares (ex. professional firmware) allow you to change the flowrate during printing.

@figuresix Год назад

@@habag1112 Checked e-steps and changed accordingly. still did not fix it, even changed to a new motherboard so I can actually flash firmware, but nope, still under extruding. And to top it all off with new board its acting possesed and trying to print things mid air after putting down a few layers.. But I do appreciate the info, thank you..

@habag1112 Год назад

@@figuresix If I had to guess, I'd blame the hardware (for the under extrusion). Check if the extruder is properly assembled (my ender 3 v2 had the gear mounted too high up), check if the nozzle or heater block is clogged, try printing at higher temp, or slower speed, check the Bowden tube (sometimes they melt over time). If you are able to, check if you're getting the temperature you requested. Try posting on r/fixmyprint. Troubleshooting FDM printers is a pain in the ass. I wish you good luck.

@Gromic2k 5 лет назад

How do i extrude 100mm filament? I can't find a function like that in Cura

@Franks3Dshop 5 лет назад

Hi, you can use the printer interface to move the E 100 mm, or you can create a gcode file with : G91 G1 E100 F100 G90 or send it with Proterface, Print run, octoprint ect.

@GreasyCarpet 4 года назад

How can I extrude 100mm on a ender 3?

@Franks3Dshop 4 года назад

You can connect the printer to a computer and use pronterface to extrude 100mm, or make a file containing the gcode to extrude 100mm

@GreasyCarpet 4 года назад

Thanks!

@toinstoychest 6 месяцев назад

He moves like a robet and dat scares me... 😰

@franki99bum 5 лет назад

vien tu de quebec frank ?

@Franks3Dshop 5 лет назад

De Montréal

@orfevrusrano2305 4 года назад

C'est un accent français que j'entends là?

@Franks3Dshop 4 года назад

Oui je suis Québécois :-)

@BlueMacGyver 5 лет назад

It is hard to make good videos, so I have to say the editing is good, but I wouldn't call us 3D printing Geeks, that's a bit rude. I will chalk it up to your grasp of the language.

@Franks3Dshop 5 лет назад

I mean Geeks in a good way :-) Sorry.

@NicolasMiract 3 года назад

se te escapo un Video en español....

@rouuuk 5 лет назад

wth the video didnt even start and u already said ''thanks for watching''

@Franks3Dshop 5 лет назад

Not sure what you saw that, it’s playing fine here...

@rouuuk 5 лет назад

In other words, its too short

@Franks3Dshop 5 лет назад

Ahhh ok I understand now! Thanks ;-)

@serkanozkan8793 5 лет назад

Right or not, Cura 3.6 version does not working on retraction every where is hairy lines it is fck Irritation!

@Franks3Dshop 5 лет назад

Try some combing options, it usually helps. Make sure your extrusion is well calibrated and that the flow is 100% in Cura. I am also using Linear Advance in Marlin and resolves this and make better seems on the outside, you have to configure Marlin 1.1.9 to active it.

@rongarza9488 3 года назад

Okay, he got 96mm at his current extrusion rate, say 100mm/s. So 100/96 = 1.0417, The current extrusion rate needs to be increased by 4.17%. TEST IT! 96 x 1.0417 = 100. Great! Now, if the current extrusion rate is not 100mm/s, then use whatever value it is set to in place of the 100 in the division above.

@Franks3Dshop 3 года назад

Hi, the 100 is there so you calculate de difference from 100 for your measured extrusion, you can use 200 and try to extrude 200 instead it will give you more precision. A difference of -2% is not an issue. And if you get some stringing you can backoff a little.