No video :(

Ford Quick Tips #81: Removing Rusted Stuck Oxygen Sensors the Easy Way!

Подписаться 849 тыс.

Просмотров 1,1 млн

50% 1

In this video we go over a few methods for removing stuck and rusted in oxygen sensors every time without hassle.
These are the Parts and Tools I recommend:
High Intensity Map Torch-
amzn.to/2keOCBr
Quality Rust Penetrant-
amzn.to/2j91pEy
Oxygen Sensor Sockets:
Full Height-
amzn.to/2ySK1cB
Low Profile-
amzn.to/2kKoy0a
Oxygen Sensor Thread Chase(if needed)-
amzn.to/2B93CeC
My Company BSG Automotive offers Auto Repair services in the greater Chicagoland area.
Website:
www.bsgautomotive.com
Facebook:
/ bsgautomotive
Catch up with us on-
Facebook: / fordtechmakuloco
Twitter: / fordtechmak
Instagram: / fordtechmakuloco
My company RU-vid Channel- BSG Automotive providing repair advice on makes and models other than Ford: / bsgautomotive1
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user and BSG Automotive (hereinafter “FordTechMakuloco”) makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. FordTechMakuloco shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by FordTechMakuloco and therefore, FordTechMakuloco does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge FordTechMakuloco or anyone affiliated with FordTechMakuloco, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

Опубликовано:

17 дек 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 720

@FordTechMakuloco 6 лет назад

These are the Parts and Tools I recommend: High Intensity Map Torch- amzn.to/2keOCBr Quality Rust Penetrant- amzn.to/2j91pEy Oxygen Sensor Sockets: Full Height- amzn.to/2ySK1cB Low Profile- amzn.to/2kKoy0a Oxygen Sensor Thread Chase(if needed)- amzn.to/2B93CeC

@Hubjeep 6 лет назад

I was just going to post the Thread Chaser. Makes the new one go in like butter.

@Itsa_Mea 6 лет назад

I would only recommend to use a 6 point wrench to decrease any chance of stripping the O2 sensor.

@FordTechMakuloco 6 лет назад

I would normally agree that is why my sockets are 6 point. In this situation though a 12 point is fine, in 15 years working the salt belt it has never rounded a one. Plus in tight areas like where most o2 sensors are you want the flexibility of a 12 point to be able to position it easier in the small space you have for the swing.

@brandonbeard8488 6 лет назад

FordTechMakuloco have you seen or used the bolt buster tool?, It is used for stuff like this

@FordTechMakuloco 6 лет назад

@416diy 4 года назад

Nice to see someone actually showing what a miserable and delicate chore this is. Way too many people posting videos for O2 sensors where they've already removed it and make it sound super easy.

@glazier4766 3 года назад

Wow, it worked perfectly. I'd been trying to break the sensor loose for 3 days. Pb blaster, liquid wrench, wd40. No luck, . I was a little scared to put a torch to it but I watched your video and followed your directions. Amazing, after about two attempts it finally broke loose. Then I did the back and forth with the wrench, spaying a little blaster at a time. Needless to say it worked great. Thanks so much for posting this video. Really helped me a lot. I got a lot accomplish today thanks to your video. 👍👍

@trailerparkcryptoking5213 Год назад

Use brake fluid as your lube!

@apachebill 7 месяцев назад

What the old timers used to call “putting the English on it”. Sometime you need technique, not brute force. Most have to break something and spend money to learn that lesson.

@user-pf4lj1pe1b 2 месяца назад

@@apachebill Ahmed, the Car Care Nut recommends loosening the Sensor as far as it goes, rock it back and forth, soak threads with BRAKE FLUID for 5 minutes, and remove with a 22 mm box wrench (if you've got the room) or conventional O2 Senor socket. Good Luck!

@dougpeak7591 3 дня назад

I use pb blaster all of the time on rusty parts . If that don’t work heat always does

@ManicMechanic007 6 лет назад

Outstanding camera angle with easy to follow instructions. Well done sir.

@autocanuckduck7503 2 года назад

I watched about a dozen videos on removing oxygen sensors, and this was the BEST VIDEO I found. Excellent narration, camera work, and technique.

@djr3485 6 лет назад

First class lesson with great footage. Any rookie mistakes could very well turn this job into a nightmare. Attention to the details is what sets you apart.

@obfuscated3090 5 лет назад

I anti-seize ALL exhaust part threads (especially manifold studs) because dry threads beg for moisture intrusion during heat cycles and subsequent corrosion. I've removed parts I anti-seized thirty years ago with no problem.

@FishFind3000 Год назад

The new factory sensors come with some anti seize applied to the treads already.

@naterade32 5 лет назад

Thanks for the tips, got my O2 sensor out by being patient and methodical. Used a combination of penetrating fluid, map gas torch, and a snipe on the end of the wrench. Maintained slow removal and penetrating fluid after the initial breaking of the threads.

@dialeddozerdave7003 4 года назад

The night before removal soak with PB Blaster. That has always worked for me especially without a lift using jack stands.

@scottbialek4671 4 года назад

Did it, worked great. Heat, box wrench and hammer. Unfortunately I hit my fingers a couple times. Sensors was 24 years old and I tried many times to get it out. Following your instructions I got it out in under 20 minutes

@patrickmitchell3691 3 года назад

Fantastic. I had almost rounded the sensor until watching this. After using penetrant a couple of times, cutting the wires on the sensor and then putting the round 22mm wrench on, it popped right out. Thanks a lot man!!

@rockspoon6528 2 года назад

I tried penetrant and 4 different specialized wrenches with extensions- all that did was give me sore hands and start to round the bolt... then I finally decided to give a propane torch a go. Heated it for around a minute on full blast then slapped on a normal wrench and it turned like butter!!! This was on an upstream one rather than a downstream, but it worked just the same!

@kidger3703 2 года назад

wish me luck brother I'm bitting the bullet this week 🤞🏻 all else fails 😡🤬🪓🔨🪚

@KRColson Год назад

Great advise! Patience is the key. Slow and steady wins the race! Thanks so much for sharing.

@cliffperrino3015 6 лет назад

your a real pro real good instructor with out any attitude like some of these yahoos that post,thanks again.

@boobalew 6 лет назад

Had a similar experience with an EGR Tube on an '04 Explorer. Ended up using the preheat holes on a cutting torch to heat the gland nut at the Exhaust Manifold. It "Squawked" all the way off! Unreal!

@jpvSoccer 4 года назад

Hi, I just wanted to thank you for your tips on not damaging the threads. I pulled mine today and was very careful; threads intact. U da Man! Best, John

@jamescallaway7376 2 года назад

Great video, I've been there numerous times, I have also found once it starts to move after heating use a enough force to retighten and untighten with some penetrating oil, to break up the rust in the threads. When refitting use a specific high temp anti seize grease or similar (not the cheap stuff) if not fitted already to the sensor.

@DaddaWins 3 года назад

I rarely leave a comment on RU-vid, i would like to let you know, your video was so helpful and right on the money, heating and DW40 is the way, take your time and it will come off, i even stripped mine and still works, again thanks for sharing and keep up the good work!.

@fishsquishguy1833 6 лет назад

Big believer in using heat as well! When it's got a nice glow I spray it again with the penetrant. It's usually not flammable but you got to be careful. I swear it'll wick in like solder and flux at that point, plus I think it thermal shocks it too to help it break free. Good vid though! Just be patient is the whole trick I think though too.

@anima_vestra_gaming2419 8 месяцев назад

Yea mine just gonna stay in there forever. Tried getting it out all day with torch, penetrating oil, 02 sensor special socket, breaker bar. Nothing will work won’t budge even a little. I’m loosing my mind.

@VeganHorseman 6 лет назад

Another great video Brian. I bought the O2 sensor for the wrong bank last year and will be installing both sensors for my 05 Escape in the spring when the weather is warmer. The timing for this video was perfect.

@snoopdogie187 6 лет назад

Even better, I was planning on changing mine (on a Jeep ZJ) today, but ran out of time so sometime this week. Unfortunately, this was the exact plan I was going to go for, and didn't add anything extra to what I already know. Working on cars in the salt belt you learn to deal with stuck everything.

@nilocxoc3488 2 года назад

Thank you sir, I would have messed getting o2 sensor off big time. Heat is a wonderful technique. Thank you again for your time and effort doing these videos. Brilliant job. Best Regards Colin

@kirbydenson3201 5 лет назад

Thank you FordTechMakuloco I used your advice on a 2005 Chevy pickup O2 sensor worked great.

@weekendwarrior3619 4 года назад

Good advice, I had the same problem on a 1997 Maxima, thought I could get it off with a wrench, but had to get it torched at a local mechanic shop and once it got beet red hot, loosen it and tighten it back on before totally removing it so you don’t damage the weakened threads.

@mikemaj8467 3 года назад

This is how you do it in my experience. Nice video! Too many people rush and break or strip threads. I'll start soaking with penetrant days ahead and repeat the following days if I think I'm gonna have a problem, then start heating with mapp gas.

@cnm642 6 лет назад

Thanks for the video! Helped give me confidence to get this done. Came out real easy only after a couple times I heated it up!

@dulay1234 4 года назад

This was a great tip. It saved me hours of time and headache. Thanks a lot.

@MrBmoll5858 Год назад

I will be doing this in about two weeks, your videos are so helpful. Thanks for sharing your experience and knowledge. 👍👍

@lakeerieflipper9349 6 лет назад

Thanks for this video. Worked like a charm. Great walk through and great tips. Made this so much easier.

@juiceybananas5489 5 лет назад

Very informative video, thank you for the helpful tips. You made my sensor changes easier for sure.

@zachd150 2 года назад

Thanks so much, I have a Ford Focus and I went out and got an O2 sensor wrench/socket and was surprised it wouldn't budge despite torquing on it with my 1/2 ratchet. Hesitated to use penetrating oil since it is a sensor, so decided to consult YT and found your video. I will be trying the heat now after watching. Thanks!

@JohnSmith-xx1lx 10 месяцев назад

Best 02 removal video. Very thorough covered all steps and options.

@mikesal8088 5 лет назад

Best advice on breaking loose my rusty 1992 GMC Oxygen sensor. WD40 wouldn't cut it. Propane torch worked wonders first time. Save me time and money doing it myself. Subbed.

@DvjLuna 5 лет назад

This video is very helpful.... I just changed the O@ sensors on my E350 XLT Van and the one sensor on the driver side of the engine was not breaking loose. Took a torch and just heated the flange that the sensor was screwed onto just a little bit and with a little bit of effort, the sensor broke loose. OVERALL it was very easy to change the sensors out. I got lucky because I have heard that sometimes these sensors are an outright BEAR to get them changed out.

@ovalwingnut 4 года назад

GR8T vantage point for the CAM 👍😎 I'm just imagining that one in a inaccessible location. You wonder why there isn't a different attachment method. It just madness. Thank you for such a great example. Cheers! ❤

@daddyge0 5 лет назад

Dude you have the lifted over you head... I'm laying down on my back with 30mph winds lol

@FordTechMakuloco 5 лет назад

Yeah I know but I worked for many years on my back too and it works.

@Lordosvk 4 года назад

HAHHA same here :D almost orcane is here 50-60km wind :D

@stevedonelson5822 4 года назад

Try doing this on your back when it's -30° on your back in Michigan

@johnhaskett439 4 года назад

@@stevedonelson5822 Steve that's on a good day in the warm snow.

@stevedonelson5822 4 года назад

@John Hasket that's all in the past now. I live in Cali where everyday is a warm day lol

@mexicaG933 Год назад

this was an outstanding job , it doesnt get any better than this

@johnsplechter5405 Год назад

Hey buddy, I replaced one of the excess O2 sensors on my 12 f150. Wanted to say a big thanks for the videos. You have aided in my truck getting a new transfer case electric motor, thermostat, fuel level switch,, fixing coolant leaks (bad O rings), and now the O2 sensor. Thanks again!

@johnsplechter5405 Год назад

The map gas and a 22mm wrench did the trick.

@EDWARDTREVEY 4 года назад

You sir have patients as I was watching this all I wanted to do was to force that wrench. So this was helpful and enlightening I have found that I am not this guy!!!

@eliotprowse2514 6 лет назад

Thanks! Very thorough. Luckily I didn't have to use the heat, but a lot of leverage. The tip about moving it back and forth and being patient really got it to come out well. (99 Altima - downstream sensor)

@michaelgossett1415 2 года назад

Thank you, I really appreciate the no nonsense approach. Straight to the point!!!!

@pierreguenette2768 3 года назад

Thank you for your technique, it works very well. Saved me a lot of trouble and time. Hope you continue to publish your good work Thank You again

@Viper81766 6 лет назад

Want to say thank you for all the great videos you post here. Thank you for your service in the Marine Corps and wishing you and your family a safe and blessed Christmas .

@rstar88105 6 лет назад

This way looks like it will work but takes a lot of time. From working at an exhaust shop a few years ago in Michigan the way we would do it is this way. Using an O2 sensor socket that wont stretch open (Blue Point YA9375B or the Schley 93750A are good options) break it lose with no heat or oil using a long 1/2 ratchet or breaker bar. If the threads are cross threaded after removal use an actual 18x1.5mm tap clean the bung hole. install with just a touch of copper anti-seize on the threads and hand tighten with an open end wrench as tight as you would an oil drain plug. Those sockets I listed were great, I never had an issue with them rounding the nut part of the sensor or stretching open even with a cheater bar. we would also not use heat because the thread from the sensor would get pulled off and and stay with the bung. Either way a 18x1.5 tap will clean it out fine.

@austincollier14 4 года назад

werealeyes heating it up doesn’t just make it easier to remove from the exhaust, it helps prevent breaking anything from applying too much stress on the parts. If all you’re doing is replacing a bad sensor the last thing you want it to snap the threads off the pipe. Especially with guys like me who are doing this off their back in their driveway. Lol

@zenithperigee7442 2 года назад

@@austincollier14 , yep, that "removing it whilst on the ground with your arms above your head" adds a new level of "difficulty" to the job. Most of the guys in these vids have the vehicle on a lift. Much easier to leverage the application of force. And whilst I'm not the "pro mechanic" and there are those "exceptions", the point of applying heat is to expand the metals. We know that metals expand when heated and contract when cooled. I've witnessed time and again countless fasteners/sensors etc., being successfully removed simply by applying the right amount of heat.

@joevignolor4u949 6 лет назад

I've gotten a few tough ones out by cutting the whole body of the sensor off with a hacksaw or Sawsall. You make the cut right down near the hex nut. Then heat and lube it and use a regular 6 point socket and a long breaker bar. This technique also works on things like power steering lines and brake hose ends. You cut the line off and then you can put a regular 6 point socket on the hex nut and use a breaker bar to turn it. In really tight spaces use just a hacksaw blade and wear a glove. The soft aluminum lines are very easy to cut. I ALWAYS use this method exclusively to remove power steering lines from power steering racks and pumps. After removal be sure to wash out the holes with some spray to remove any metal chips left over from cutting the line.

@HagakureJunkie 6 лет назад

Much love for this advice brother!

@vicenetlabisfun5600 4 года назад

thanks so much! did it the way you showed in the video and the bad O2 in my 2006 honda accord came right out. Just as a safety measure make sure you wear gloves or let things cool off for about an hour I made the mistake of grabbing the box end side of the wrench after 15minutes and it was still piping hot. I should mention that it all just took me 10 minutes it doesn't take long at all.

@michaeldvorak5556 3 месяца назад

You have provided an excellent tutorial. Thank you. Spraying it with PB Blaster, Liquid Wrench, or other rust penetrent after you have it broke loose will help. Tapping a seized sensor can help the penetrating oil seep in. Multiple heat cycles are a big help to break the rust bond. I suggest using a 6 point box wrench instead of a 12 point. Less chance of rounding off the nut.

@FordTechMakuloco 3 месяца назад

You obviously have never removed an oxygen sensor in a tight place. There is a reason why I do what I do. Oh and BTW it is much harder to round the hex at this size so even with a 12 point you are ok.

@michaeldvorak5556 3 месяца назад

@FordTechMakuloco yes I have, and it's a bitch. Yes, sometimes the 6 point just doesn't work.

@mikecont9742 5 лет назад

Great step by step. Really appreciate the time and knowledge you gave.. thank you..

@waterpic1 5 лет назад

Thanks so much for taking the time to shoot this, it was extremely helpful to this novice. I didn’t need heat, but being patient, tapping with a hammer, and your technique of back, and forth was key to getting this damn thing out.

@CharlieKulins 6 лет назад

Thank you. This procedure worked perfectly. Excellent !

@jakes6023 3 года назад

Well, back to my cold ass wet driveway I go!

@davem3789 6 лет назад

Excellent content as always! Thanks

@michaelmurray121 6 лет назад

Hey Brian, I did the same with the torch n penetrating oil make it easy without damaging the treads . Great video 💪🏽

@barthk3640 3 года назад

Just did the 2 up streams on my 03 cvpi vic. 15 min on 1, 5hrs on the other 🤬🤬🤬. patience and heat. Ur best friends for this one.

@tillman40 6 лет назад

I love the PB Blaster for this application

@WalterMelons 3 месяца назад

Old comment but Liquid Wrench! Project farm tested penetrating oils. Best was making your own mix of 50/50 atf/acetone but liquid wrench was a close second. Pb was like 5th.

@dandeleona4760 5 лет назад

Re: stripping threads with impact: "Trust me. I've had experience..." lol. Nuff said. :D

@claudiar8575 2 года назад

Thanks your explanation along WITH video footage it's so great....wow. thank YOU

@Karlie-ee9kf Год назад

Just the video I needed I got one replaced myself the rest were rusted and wires were spliced and reconnected where the previous owner tried to replace and couldn't break them loose I can't wait to see how it runs with all new ones!

@icemule 5 лет назад

"Trust me I'm experienced" Part snaps in half! LOL! Just kidding, but I think we have all thought that until.....love his channel, dudes great, I trust him and that's priceless!

@gunners4129 4 года назад

He has Mac tools. Usually means he was a tech. I thought it until i saw that lol. That and the Mopar penetrant. Best guess he worked in a local Chrysler Jeep Dealer

@owboky102050 5 лет назад

I've been using Mapp gas since the 70's heats it red but never blows thru .. THE BEST!!!

@Guppypants 4 года назад

Thank you. This video prevented me from having to replace my exhaust pipe.

@price9195 2 года назад

changed my 3.5 ecoboost bank 1 last week. sprayed, wrenched, MAPP gas the whole works, wouldn't budge and gave up after a couple hours. Sprayed it for overnight with PB blaster. Next day, gave it a go cold and hit the wrench with a hammer a few times. It turned out by hand like magic. Couldn't believe it

@whitetiger8652 5 лет назад

Excellent job as always Brian!

@dougronson5777 3 года назад

That was an awesome explanation and demonstration. Thank you!

@kelvinadams4877 5 лет назад

thanks man really help me... I will try it I bought a truck GMC and I'm being trying almost a week and find a video thank you.

@charlesmcgehee3227 6 лет назад

Nicely done. Lack of patience has messed me up a few times over the years. There are times when you can use an ultrasonic cleaner to "repair" an oxygen sensor. If you have a cleaner, give it a try if you are on a budget. I have not tried it but there are a few videos that show it working.

@jeffreyrichard8054 6 лет назад

Brian thanks again as always for a great video

@hughmackellar7941 6 лет назад

Thanks. And Merry Christmas!

@worldwidehf 6 лет назад

first time even seeing a 02 sensor thank you

@1divemaster1 6 лет назад

Great advice as usual. Thanks and merry Christmas.

@2abuck401 27 дней назад

Thanks so much! I tried a flare nut wrench and it rounded it slightly. Got scared I'd round it off and was about to quit when I saw your video. Had it off in 5 min.

@saulsandoval2313 6 лет назад

Bravo.... Nice tip - cutting the tail off. I like it. 👍

@TradeAlgoPremier 3 года назад

Yep, experience is the best teacher. I learned the hard way. No impact gun or open end wrench.

@shaunsautorepairs5410 6 лет назад

Good tips... Always good to know these things

@seanwhalan2690 Год назад

Thanks for mentioning not to use an impact... that was a thought I had. Great video. Thanks

@tipsclubs01 2 года назад

Excellent Video on replacing the Oxygen sensors. Thanks.

@tbucks1000 4 года назад

Great video. I have to change mine out. I'm gonna try it. Your gonna save me allot of bs

@jfkesq 3 года назад

I did this on a 2006 Toyota Sienna. Used open side of 22 mm long wrench (closed side seemed to be stripping). Used PB Blaster and then WD40 and the WD40 seemed to work better. Kept working it back and forth. It was seized on there real good. Got it off. Took my time. Took lots of breaks and used a lot of solvent. Worked it back and forth. The threads of the sensor were stripped when I got done but the threads on the female side were OK. There was some metal stuck to the threads on the female side. Applied generous amount of gunk from the Denso new sensor. Hand threaded then used open wrench. Cleared the codes. So far so good. The beer tastes extra good now.

@peterwright1231 6 лет назад

Thanks - another great tip video

@johnwyman3300 5 лет назад

Right on man! Really great video. You saved me from making a mess of things. As you say “the easy way!”

@samgreer4509 2 года назад

Good work loved the tips. Best part was the sound effect of the grunting when you said tap it don't be like pulling going uuuuuuuhhhhuh 😹.

@dannyvaughn366 11 месяцев назад

Thanks, I've been working on my Xterra O2's and I used an impact wrench and it totally stripped out the threads. Good news was I had a rethread that did the job. I won't do that again. Thanks for the helpful tips

@workingshlub8861 6 лет назад

soak in pb blaster overnight....hit with torch. works every time..another good video brian.

@FordTechMakuloco 6 лет назад

Letting penetrant soak is the hard part for me.

@Streetpreaching7 4 года назад

@@FordTechMakuloco 04 F150 5.4 3V just changed Bank 2 Driver side sensor 2 on outlet of convertor. Texton 47749 7/8 socket fit perfect on downstream Bank2. Just enough room to glide 3/8 ratchet with a "socket and extension as a make shift cheater bar" on end of ratchet. Soaked in PB blaster about 7 applications in 20hour period threaded out by hand the moment it broke free; no torch needed. Thanks for all your videos Sir! It was the original 02 sensor rusted in goooood. Fixed P0430 code!

@christianbeleznai3351 4 года назад

Hey your videos are great. Very clear and nice explanations of what you are doing and why. I was going crazy last night with my lower O2 sensor, gave up and watched your video, did what you said this morning and it was easy peasy. Thanks!

@johnrawlinson4946 2 года назад

Thank you. 3 years later this is still helping people. Just nail the down stream sensor.

@mydrums4evr 3 года назад

Great video! Right to the point, thanks for the tutorial..

@JackBeeler 5 лет назад

wow seriously best RU-vid video and instructions.

@idiotburns Год назад

This video is so well put, I HAD to subscribe!

@denniswilkinson1118 6 лет назад

Welldone Brian, good info!

@DERF010101 2 месяца назад

Thanks a lot for this! I was struggling getting mine out. After watching your vid I had it off in 5 minutes.🎉

@JL-dz8sj 6 лет назад

step number 1: obtain a lift

@nickguitarguy1 4 года назад

I'm doing O2 on the ground today, no problems so far.

@papabits5721 4 года назад

Nicholas Graham getting to old for the driveway

@bishop5166 4 года назад

Stop crying. You don't need a damn lift for everything. Use some cardboard and a couple of cinder blocks under the front wheels, you'll have enough space to do whatever. Step 1 get yourself a map gas torch.

@MakingMovesMajor 4 года назад

@@bishop5166 Step 1 shut up

@NathanKirby2001 4 года назад

@@bishop5166 some of these guys are ancient

@alanbickford175 Год назад

Great video with great explaining and camera angle.

@mattjacomos2795 5 лет назад

good tips on not destroying the threaded housing. I plan on doing this job after I recieve my OBD reader to see if the sensor requires replacement.

@yuneman1 5 месяцев назад

I'm about to replace my pickups Oxygen sensors and this video seemed to make it easier hope I can replace them with no problems..

@berniceperry8898 5 лет назад

Just subed to your channel...my names Howie and would rather work on a ford as drive anything else...awesome vids keep it up...

@what9621 3 года назад

The best I have seen so far.

@donalderdbrink647 6 лет назад

20 years original Motorcraft equipment,no too shabby ...Built Ford Tough💪 good for another 20

@aggiejet Месяц назад

I’m watching this because I’m replacing an O2 sensor on my 2018 F150. Got a whopping 6 years out it. Modern F150’s have lots of problems. I drove. Dodge Ram for 25 years. Regret buying this F150.