Thank You for Watching the Wiring Video! Subscribe To This RU-vid Channel: ru-vid.com See My Wiring Playlist: ru-vid.com/group/PLsF7T1tRFy2hmiiUUfMZNyV-BUA_yrPIh
Just found your videos (specifically this one as I have a fuel pump in a 61 Studebaker that I'd like to protect with a cut off) and just wanted to say how impressive they are. Super high quality, very technical but done in a way that is easy to follow/understand. Hope you keep making content!
Thank you! If people keep watching, I’ll keep making them for sure. I’m so glad that so many people have found them helpful!! I’ve got a few cool ideas coming up in the next couple of months. I just need to find the free time to do it all :)
Fun fact: TCM is located in the front of engine bay. Simply open their hood, unplug TCM and take one pin off. Plug back in and they will be unable to start
Haha! Thank you so much for watching! The wiring videos are totally rocking right now so I’m going to ride the wave while I can. I actually wanted to get your feedback on something. I’ll reach out via IG in a bit! Also - I was a little sad to see the El camino leaving, but I’m more excited to see what your next adventure is! Glad to hear it’s going to a good home!
Thanks for the simple explanation. I tried out one of those oil pressure switches, but I couldn't figure out how to wire in a way that would power the pump during starting, so I would have to crank, build oil pressure, then refill the carbs with fuel. Not ideal. This set up should be a lot better, and less points of failure in my oil system
Actually that is a good idea if your running a electric fuel pump or two and you get into a accident that hits hard enough to warrant the protection . The fire starts in milliseconds and why feed it so you have less time to escape . I worked at Ford in the 90s we had a few that malfunctioned but Ford fixed them by using a updated switch in the trunk near the tank never seen a comeback after that . That really is a good idea for a lot of reasons on a hot street car or any car for that matter .
When I got hit on my rear driver side my car would not start anymore so I had it towed to a mechanic and he told me it was a reset button in my trunk that needed to be reset. He only charged me for the tow. I'm assuming it was the inertia switch. It was a 1999 Ford Taurus sedan.
I have been a subscriber for a long time but I stopped watching for quite a while. I ran across this video and I was really impressed! Your presentation skills have improved dramatically, and your explanations are spot on. Keep it up and you may get a following like Chris Fix and you can quit your day job.
4 decades ago before we had inertia switches I had a car that had a fuel pump relay switched by the oil pressure switch, positive from the ignition negative to the oil pressure switch , pump on the relay n/c . OK for off road cars etc. It had a carburettor so it would still start.
@@WiringRescue Thankyou very much for raising this subject, my classic has no fuel cut off system at all I will be wiring in both, could be a life saver being unconscious with a fuel pump running does not bear thinking about.
I am from Egypt and i keep watching your vidoes Keep on Man ,, you are doing the best vidoes in world Can you make video for wiring Gps tracker with eninge Cutoff relay ,, causr thieves so high here If you read my comment wiill be happy of small reply
I’m glad that you like the videos. It’s really incredible knowing that people around the world are able to learn something from me. I really like your gps idea, but I don’t know anything about how that works. I’ll look into it though! Thanks for watching!
4:16 That "C" does not stand for "Control", it stands for "Common". JFYI, the normally open can be used to install an indicator light, buzzer, or to some control module (if you wanna get fancy). A buzzer would be very useful if someone were to bump you in the parking lot, and when you try to start your car, the buzzer comes on right next to the switch.
Totally agreed, I know it is common, but apparently just had a brain meltdown when talking through this video. Sorry about that and thanks for the point of clarification.
@RattyMuscleCar Not a problem. Sometimes, when someone missspeaks and says the wrong word, even tho they know the correct word, it might misinform a viewer. Then it can start the game of telephone. As in, they go to the store and ask for the switch that has the "Control" connection, and the guy at the counter looks at the guy confused and says, "What!"
@@AztecWarrior69_69 the morons working at the parts store have no idea what most people are talking about. If it's not listed on the computer screen, they are dumbfounded. Who goes to the store and asks for a switch with a control connection? If you are even remotely intelligent enough to know how and why you need an inertia switch, you're going to ask for an inertia switch. I get the feeling that you are the guy who is a self declared expert on everything and like to hear yourself talk... the guy no one likes at the party.
@@TheRoadhammer379 "@Aztec_Warrior69 the morons working at the parts store have no idea what most people are talking about. If it's not listed on the computer screen, they are dumbfounded. Who goes to the store and asks for a switch with a control connection? If you are even remotely intelligent enough to know how and why you need an inertia switch, you're going to ask for an inertia switch. I get the feeling that you are the guy who is a self declared expert on everything and like to hear yourself talk... the guy no one likes at the party." When you read my comment, somehow in your brain it translated into, "Tell me you work at an auto parts store without telling me your work at an auto parts store." which made your reply " the morons working at the parts store" then continued with yours brain dead comment. "Who goes to the store and asks for a switch with a control connection? If you are even remotely intelligent enough to know how and why you need an inertia switch" Where did I say that they were going to be specifically asking for an inertia switch? I just said " they go to the store and ask for the switch that has the "Control" connection," I know you meant this to be in your favor but you only made mypoint even more clear. You said "If it's not listed on the computer screen, they are dumbfounded." So even more reason to have the terminology correct. "Who goes to the store and asks for a switch with a control connection? If you are even remotely intelligent enough to know how and why you need an inertia switch, you're going to ask for an inertia switch." Again this pertains to all switches that have a common " I get the feeling that you are the guy who is a self declared expert on everything and like to hear yourself talk." So just because a correction was made to help others your lack of intelligence goes to weak minded assumptions. "the guy no one likes at the party." Says the guy who trying to be the know it all, by failing to inject some weird lackluster correction. Yeah, it clearly show you don't even get invited to the parties. I feel bad for you.
Rover used to these identical inertia switches in line with the feed to the pump rather than controlling the fuel pump relay, no chance of a stuck relay keeping the pump running.
That’s interesting! As long as the inertia switch is rated for the proper amperage for the fuel pump, that seems like a fine way of doing it! Thanks for watching!
PLEASE ..there are to fused triggers......one goes to the battery....but can i install the other lighter fused trigger to the positive side of the coil? thank you
Jeremy, you suggested a switch on the dashboard with relays. I have a similar issue with installing this on a 1993 GMC 3500. The 25 Amp fuse wàs shorted. The running lights are on all the time while running. But no headlights. With a new switch and bulbs installed. Can this shorted 25 Amp fuse under driver's side dash be converted to a switch like you suggested? Please diagram and explain it. Thanks. Lynn
Hi, this is a great video and it really helped with a retro fit of an electric fuel pump on to a 1972 Spitfire. Now here is the part I am struggling with. With the same set up that you have demonstrated, how would I wire a warning light into the circuit so that if the inertia switch is activated (pot holes) I have an visual aid on the dash to tell me the inertia switch has activated and the fuel pump has now turned off? Any help would be greatly appreciated. All the best, Gary
Wire a test light on the pump side of the inertia switch. Drill a hole in the dash somewhere and install it. It will flash on and off while the engine is running as the ECU cuts the pump on and off to maintain the proper fuel pressure. It will also come on for a few seconds as soon as you turn on the ignition switch as the ECU brings the fuel pressure up to the specified level. The test light could be an LED with a 600 ohm resistor wired in series with it or it could just be a 12 v incandescent instrument lamp, like the kind that light up your speedometer and dash.
Came across your videos , great job by the way . I'm having a problem with my truck that everyone I talk to is scratching their heads . My marker lights and tail lights and also the dash stays on . I disconnected the switches (toggle) I've pulled all the relays and circuit breakers out and the lights are still on . This is the real head scratcher ..... I disconnected the batteries and the lights stayed on for at least 20 minutes . Any ideas My truck is a 2001 kenworth w900 Any help will be greatly appreciated
Hi Ronald. The easiest way to diagnose this is to get a wiring schematic for the truck. That way you can see where the power is coming from in the light circuit and follow it back to the source. That being said, there are a few things that come to mind. 1. Any weird aftermarket stuff - has the truck had any things added to it around the same time as this problem started? Alarms? Lights? Radios? If so - start with that. Maybe even remove it entirely. 2. For lights to stay on there has to be a source of power. It could be a backup battery of some sort, or a capacitor in some component. I know it sounds crazy but it has to exist, unless your truck is a magical energy source, which is unlikely.
Ronald, did you disconnect each and every battery? You can't simply pull the positive cable off on battery and think the truck is disconnected from the batteries. My peterbilt has to have all the cable links disconnected on the negative side of every battery or else some accessories continue to draw power. My fridge is factory installed and will continue to be powered if I don't disconnect all negative cables, same with my instrument panel and dash cam.
Prob a stupid question BUT could this be triggered by a pot hole or say in an autocross environment where you will have a lot a Gs in different corners and brake/acceleration situations?
It definitely could. There are lots of different style inertia switches that can be bought though. An OEM one from a Ford may be the best option because they are designed with potholes and normal daily driving in mind.
@@WiringRescue 100% what I was thinking while looking at switches on amazon. Any reason why these are put onto the fuel side vs say killing an ignition box?
@@chargerman426 - I don’t know for sure - but I imagine car makers may believe that pumping fuel after an accident is the worst case scenario, so that’s their number one thing to shut down. Just a guess though.
I have a question that i hope you will reply to, I have a set of 7" jeep headlights in my mk1 golf. All the lights work fine with all their respective sources of power. The issue I am faced with is that the angel eye stays on when indicating and doesnt allow the amber to flash. Is it possible to wire the parklights in such a way where power cuts to the angel eye in the direction Im turning and then back on when the indicators are off.
Hello there love the videos, just subscribed. I have a request, I'm thinking of buying the Vevor Diesel Heater 12V from Amazon. Could u maybe do a wire up video of that please? Thanks in advance
Great video but Noob question here sorry so I’m in the middle of installing a walbro fuel pump on my charger scatpack and I’m installing a relay and I inline fuse so the wiring would be pretty similar to this correct minus the inertia switch and instead of a wire going to a spst switch it would be spliced into my ignition wire instead so the pump would start when my car starts?
You are on the right track. The thing to consider is when you want the pump to turn on. Should it be when the key is on? Or should it be ONLY when the engine is running. That will determine what wire you use for pin 86. Also check this fuel pump video out. It has some additional details you may find useful ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-8GjvRdssvFI.html
Ford has been using inertia switches since the 1990's, and they have worked really well. Occasionally they do go off unexpectedly due to water intrusion, or minor parking lot accidents. For the most part though, they handle all normal road conditions just fine.
Love how you did this! Do you know if there is current through the C - NO after you whack it with a hammer? Could be cool to wire it to a service light or something.
You can use both circuits. The NC in series with the relay and the NO to trigger the hazard flashing lights or, as some car companies do, unlock the doors..or both.
There is no reason to fuse the switching leg of the relay as there is no load, only signal. Also the reason these aren't used on race cars is because on a hard launch the inertia switch will often trigger and kill fuel prematurely.
Exactly, it's literally what relays were invented for. And if he insisted on having the switch fused, he could've wired the switch source power to the relay source power, using the single 40 amp fuse.
at 4:20 it is not CONTROL but COMMON . If you look for 5 minutes how electric diagrams are done you will see we often use the therm NO or NC (normally open, normally close). Also your wiring is WRONG. You should never cut the ground for security measures. Always in series of the switchs.
The video is good . But NOT GREAT. ? WHAT SIZE FIUSE DIT YOU USE . WHAT SIZE IS THE BIG FIUSE AND WHAT SIZE IS THE SMALL FIUSE. I am disappointed. I can't finish this project. Without this information
You should probably watch my video that explains what size fuse and wire size you should be using. Hopefully it helps. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-EhzN6UdnmPA.htmlsi=BIPvQ_w56XvmEXR2
It’s still around I promise! I had to set it aside to get the heat and ceiling finished in the garage. But both are now finished as of this week! So I’ll be wrenching (welding) on it again. Thanks for sticking around! I appreciate you!
Nice videos ty for sharing, can you help us about safety shutdown relay as a solution, When the ignition is switched on, the relay switches the fuel pump on for about 2 seconds and then shuts it down again, the fuel pump switches on only when a running motor is detected its possible? TIA