(FX Impact) How to Install Your Tungsten Hammerweight

Подписаться 2,6 тыс.

Просмотров 13 тыс.

50% 1

In this video we go over exactly how to install your Tungsten Hammerweight into an FX Impact.
Order your Tungsten Hammerweight (FX Impact) here:
utahairguns.com/fx-impact-tun...
If you have any further questions, comments, or video requests leave them below!

Хобби

Опубликовано:

29 ноя 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@redscorpionairgunner525 5 месяцев назад

Thanks Rob my hammer is stuck inside ill, keep working on it! great video

@whiteykauai 2 месяца назад

Did you work it out? What caliber were you using?

@WvMnts 10 месяцев назад

Great video

@alialmahfudi7498 4 месяца назад

Great job and thanks

@airguns_rc Год назад

Agreed, It was an easy install.

@arcticairgunner 11 месяцев назад

Could you please make the same type of video for the maverick? Thank you.

@nioviapartments4052 Год назад

Hello I have a question doing this installation what position should the macro and micro wheel be so that we have 6 to 6.5 mm .Thanks

@fabiocarvalho8180 Год назад

what is the name of this yellow picatinny wrench? And where to buy it? Thanks.

@derviskarapinar5131 Год назад

With the old hammer and macro set at 16 the micro adjustment would go well past 5 setting and I could still cock the gun Now i go with the micro past 4:41 4.6 I am unable to cock the gun I noticed the begin wide part of the tungsten is approximately 4mm thicker Would you recommend an other spring

@richoperezinho7215 8 месяцев назад

Hi, how much increase in fps with the change of hammer.?

@billalvarez6699 Год назад

Installed this on my m3 30 cal..micro won't let it me cock at #5..have to back off at #4 to be able to..is there a fix for this to be able to go all the way to #5?

@Fernando_Woolybooger Год назад

I connected my vice grips directly behind the C1/Hammer seat and even though I wrapped my vice grips in tape, I still scratched the valve rod a bit where the vice grips attached. Is that bad? Do I need to replace the valve rod now? Maybe take some ultra fine grit polishing paper and polish that spot?

@chrisfigueroa3361 Год назад

No just give a little polishing with some 3M polishing paper you be fine you can find it on ebay Amazon for about 12 bucks for a set of polishing paper I did the same so I just polished everything the rod spring hammer weight and hammer guide and C1

@kevinJmadsen Год назад

A heavier hammer or a lighter spring setting should have an equivalent effect.

@derrickmitchell39dm Год назад

What is this installation do for the Impact?

@212caboose Год назад

Heavier hammer increases valve dwell. Basically the valve stays open longer and allows for more power.

@chrisfigueroa3361 Год назад

Does that void warranty? 🤔

@utahairgunsworkshop Год назад

No. It doesn't :)

@chrisfigueroa3361 Год назад

@@utahairgunsworkshop I have a question if I was to buy the new power block plenum kit the whole thing for my mk2 can I just swap block and valve house from my m3 that I have already kill two birds with one stone will it work I'll just use new power block and valve on m3 and the rest will go on the mk2 let me know

@utahairgunsworkshop Год назад

We wouldn't recommend it but give us a call if you have any further questions.