GOEREND TRANSMISSION: OVERDRIVE SECTION

Подписаться 1,3 тыс.

Просмотров 42 тыс.

50% 1

Goerend Transmission Overdrive Dis-assembly and Re-assembly
Check back for additional video with information
**This is approximate information only and may not apply to all transmissions. Goerend Transmission Inc. holds no legal responsibilities for any problems (mechanical or otherwise) caused by following the instructions in this video.

Авто/Мото

Опубликовано:

29 мар 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@jimkillen1065 Год назад

Dave has helped me before fix my friends 47re a broken second gear strut . He took time years ago to explain to me how the triple disc convertor holds more than the single back when folks said there was no difference in holding . I guess that's been put to bed lol . I always been a fan of Dave's products.. if I had a automatic I want there products

@Ashroyer86 5 лет назад

That last part I think was pretty important from what I've heard, glad you mentioned it. But would be nice to see where you measured that "width".

@montrosepatriot 7 лет назад

the 5 disc pack is recommended when overhaulin a 42RE with the stock 2 or 3 discs

@dieselmakesmehappy 6 лет назад

Very helpful thanks!

@HaythamBuKhadra 5 лет назад

Thank you.

@kenbrandt6104 3 года назад

This would have been a good time to show installing the repair shim.

@andrewjessen764 6 лет назад

So if you needed to replace just the housing, there is no need to disassemble the internal overdrive section? Sounds like something I could actually do myself if that were the case (I don't have a press). Great video.

@sknfjuebc 4 года назад

Same situation I’m in

@AndrewBrowner 2 года назад

put me down for the same problem, going to give it a go and just throw the known good parts in a new unbroken housing and hope for the best

@andrewjessen764 2 года назад

@@AndrewBrowner Worked good for me.. I shoved a #2 pencil in the parking paw to get it out. Going on 3 years without an issue. Got my housing from Cascade.

@AndrewBrowner 2 года назад

@@andrewjessen764 i got the housing off, the park rod stayed with the transmission, ive heard its a pain to get it back behind the pawl, did you just slide the housing on and spin the output slightly to get it to pop behind the pawl?

@andrewjessen764 2 года назад

@@AndrewBrowner Yes I believe so

@omarmonzo5426 7 лет назад

how do you check the clearence?

@MrPapasmurf1961 4 года назад

witch trans is this one its just like minebut i dont no yr or witch one it is it has been replaced ty

@pedronazario223 6 лет назад

how to align the axis inside

@person440 4 года назад

Where do you measure the width of the piston at when selecting the correct spacer. That information is of no use without knowing where you measure the piston at.

@c-low6010 5 лет назад

Fiber steel

@manueltorres1741 4 года назад

Tengo sin serevsa

@felipevalles8041 2 года назад

does this part can fix the reverse issue ? thanks

@Junior-hd2hc 2 года назад

Does urs not have any reverse or did u get it fix?

@felipevalles8041 Год назад

@@Junior-hd2hc mine got some but it feels like is shaking when I applied it, I have to give her a little push to back up , im going to open the fluid pan to see whats going on.

@Junior-hd2hc Год назад

Alright I took apart my transmission, nothing was worn except the OD housing. The snap ring that needs to be pressed on was broken and the clutches werent pressed on. Gonna try and drive it this weekend.

@Junior-hd2hc Год назад

Also when I open the pan I saw pieces of the snap ring that broke