GT3000 Front Wheel Bushing Upgrade.

Подписаться 147 тыс.

Просмотров 19 тыс.

50% 1

The gt6000 GT5000 and GT3000 all use front rims with bushings that over time need to be replaced. For all the trouble they are to do you might as well upgrade.
10Pcs Flanged Ball Bearings ID 3/4" x OD 1-3/8" for Lawn Mower, Wheelbarrows, Carts, Hand Trucks Wheel Alternative to 532009040, AM118315, AM127304, 10513, 251210
amzn.to/34CeWwN
Astro Pneumatic Tool 930 Air Body Saber Saw with 5pc 24 Teeth per Inch Saw Blades
amzn.to/2HPmvaX
Diablo 6" Carbide Tipped General Purpose Reciprocating Blade 9-6 TPI (3/32"-1/4") (3 Pack)
amzn.to/3kIINcx

Авто/Мото

Опубликовано:

28 окт 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@unclemichael3577 Год назад

I couldn't pre-cut the bushings so i just took a 10" punch & a real hammer & knocked the old bushings out. Saving my flatheaded screwdriver for screwing flatheaded screws : )

@timidater4803 Год назад

why not driving out instead of cutting the bushing?

@srg6532 Год назад

Looks like a long punch placed inside to get to the other bushing and hammer it out would work.

@ProleDaddy 2 месяца назад

It tends to work for both of them.

@111000100101001 2 года назад

Great how to! I can’t believe how bad the old ones were worn, especially the knuckle shaft. Bet she drives a lot better now and probably mows an inch higher ;)

@scottsnell2888 Год назад

Thanks for the video! Just ordered some bearings for my GT5000!

@rudygeorgiamulesandcountry1594 Год назад

Just punch those things 0UT ... ! For the first one I just utilize a 3/8" extension and a heavy hammer ! For the second side I use the same 3/8" extension, but with a properly sized socket on it, then I place the first bushing that I punched out; placed lightly back into its original bore as a guide to help keep the extension with the socket aligned vertically to ease removal of the second bushing . Hit them hard ... !

@alanseager 6 месяцев назад

thank you my friend ordered some bearings

@michaelwittke8336 2 года назад

I was lucky, used a sacrificial 1/2 extension and a hammer, popped right out

@thurm101 Год назад

3/8 extension out of your socket set. Tap out the opposite side with a hammer on both sides. Then tap in the new bearings with the 3/8 extension with a 1/2 socket attached to the extension. Grease the inside (optional). Also clean up the axle and sand paper lightly.

@roberthursman3055 3 года назад

You didn’t need to cut All you had to do was tap out the old bearing and put the new upgraded bearing in and don’t forget degrees it takes 10 minutes or less per wheel

@redneckcomputergeek 3 года назад

Ever wonder why How to RU-vidrs turn off comments? Its because of comments like this. I point out clearly twice in the video this point and that these are way more stuck then they should be. I live in the rust belt and everything is harder to fix because of it. Thank you for the confirmation on how it should have been able to be done.

@kendurell8085 2 года назад

I agree with Bob. Just changed mine. No sawing is necessary.

@sladeeli7 Год назад

I have the smaller spindles, they’re closer to 5/8” with 7/8” diameter for my wheels. Is there a bearing upgrade for mine? I can’t find it anywhere!

@backachershomestead 5 месяцев назад

How do I find out what year my gt3000 is? The plate under the seat cannot be read anymore.

@JamesMcGuire-fe6jf 3 месяца назад

Where do you buy a bushing 3/4 to 5/8” for a front wheel 15-6.00-6 ?

@BlueberryStinkFinger62 2 года назад

Depending what bushings you're using

@billsimpson604 Месяц назад

Can you say 'overkill'?

@HighestRiser 2 года назад

Will these bearings work with 15x6 wheels on the same mower

@redneckcomputergeek 2 года назад

yes on most they will work.

@paulthompson1216 Год назад

RCG...I don’t suppose you know anything about an upgrade for a TB Bronco? The bearings featured don’t fit. It appears the OD on my wheel is 1 inch. I have been searching the internet for a .75 X 1.0 bearing but can’t find one.

@redneckcomputergeek Год назад

Hillman Group 58106 Flange Bearing, Bronze 3/4 X 1 X 1-1/4 X 1-Inch, 4-Pack

@paulthompson1216 Год назад

@@redneckcomputergeek Thanks! So flange type only for the Bronco?