GU Patrol Axle Rebuild Pt 2

Подписаться 5 тыс.

Просмотров 19 тыс.

50% 1

Here's how I rebuilt the front axle on my GU patrol. In this video I will begin the rebuild of my GU Patrol Front Axle to change; King Pin bearings, Axle Seals, Swivel Hub Seals and Wheel Bearings.
This is a job that involves working on the brakes, suspension and steering, so if you are not experienced you should grab a mate who knows what they are doing to give you a hand.
This job is time consuming and requires a little know how to get it done properly. That's not to say a beginner could not achieve this, you just need to keep track of all your parts and follow these steps.
Part One goes through how to remove and disassemble the hubs.
If you have any questions or tips for others doing this, use the comments below 👍🏻.
Front Swivel Hub Axle Rebuild kit for Nissan Patrol GU Y61
ebay.us/RzeyL4
TRAIL-SAFE FRONT INNER AXLE SEALS SUITABLE FOR NISSAN PATROL (PAIR)
www.superiorengineering.com.a...
Hub Axle Lock Nut Socket for Patrol GQ GU Y61
ebay.us/9AyOjW
When you click on the above link and make a purchase, this can result in myself earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
If you guys have any questions or tips use the comments below. Hope you enjoy
Music
OOYY / Ganja / courtesy of www.epidemicsound.com

Авто/Мото

Опубликовано:

16 янв 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 45

@andrewt3952 Месяц назад

I done plenty of cruiser swivel hubs, but never a patrol. Great 2 part video mate. Helped in a few spots!👍🎯🍻🇦🇺

@ReubsModifications Месяц назад

Thanks mate glad you found it helpful 🤙🏻

@anonymity6876 11 месяцев назад

Awsome work. Great directions and info. Surgically done. 👍🤙😎🇦🇺🍻

@ReubsModifications 10 месяцев назад

Thanks mate awesome to hear that 🤙🏻

@ibsn87 5 месяцев назад

Thanks for all the tips. Fantastic video... I’ve done this before but a bloody long time ago. By the look of the end of the video it’s time do your control arm bushes too haha 😅

@ReubsModifications 5 месяцев назад

Haha definitely, they are extra castor bushes but they seem to be a little too squashed and I have changed the lift so will go back to factory bushes👍🏻

@fulviof.9450 Год назад

Nice job, will be making the same on my Y61 in the next few months 👍

@ReubsModifications Год назад

Good luck! They are pretty easy once you lay out all the parts and get an idea on where everything goes 👍

@neilkohler860 5 месяцев назад

Great stuff. Sound less daunting than i thought. Great

@ReubsModifications 5 месяцев назад

Glad you enjoyed it 👍🏻

@toneless3182 Год назад

Great work

@ReubsModifications Год назад

Thanks mate 😀

@GhostofZuuzGaming Год назад

you made that needle bearing removal/replacement so easy. Ive always had trouble getting it out. Grinded down a metal punch with a lip to catch the end of the bearing race. But about to replace my stub axles with new bearings, i noticed you used a socket to drive down the needle bearing below the end of the stub axle end. My new replacement stub axle came preinstalled with needle bearing installed and it is flush with the end of the stub axle.

@ReubsModifications Год назад

Thanks mate, I couldn’t find in my manual how far to seat the bearing so I sent it all the way home 😂

@mattbates7099 Год назад

Just a tip that's missed in the video - the manual says to torque the lock ring to 198nm before backing it off and then torquing to 3-5nm. This ensures that the wheel bearings are seated correctly.

@ReubsModifications Год назад

Great info mate, thanks for sharing I’ll remember to do that next time 👍🏻

@bjorndecorte6846 Год назад

198Nm? Thanks for the info!

@r4rekt671 4 месяца назад

Please if you do tho. Have multiple bearing removal tools! I snapped my one on the loose and they nearly were stuck at 198nm! @ReubsModifications

@amafrancotravel2910 Год назад

Very helpful

@ReubsModifications Год назад

Glad you think so, always good to hear 👍

@fulvioplozner7152 2 месяца назад

I did this job yesterday. in Europe you have to put a lot more grease in the bearings! the climate is more humid

@ReubsModifications 2 месяца назад

Great tip 👍🏻

@G1McK Год назад

Awesome work, I'm about to rebuild the set of axles I have, these videos are helpful. When is part 7 of the axle swap coming?

@ReubsModifications Год назад

Awesome to hear mate I’ve been away for a couple weeks I’ll look at getting onto it in the next month 👍🏻

@bubbleobill2654 9 месяцев назад

Super helpful video! Is there a reason why you didn’t replace the races in the brake assembly?

@ReubsModifications 9 месяцев назад

Thanks mate 👍. The race in the brake disk is for the wheel bearings, I had a look at them and they looked like they were healthy and they also happen to be quite easy to replace if I wanted to do them later.

@skitzz203 8 месяцев назад

Awesome and very helpful video mate, i was wondering how long did it take you to do 1? Mine is due for a change next weekend

@ReubsModifications 8 месяцев назад

Thanks mate, I did mine over a weekend but I was filming. I think that you'd be able to do it in a day if you had everything ready to go.

@skitzz203 8 месяцев назад

@ReubsModifications awesome thanks mate! Again thank you for informative video. I have subscribed to watch more of your videos

@ReubsModifications 8 месяцев назад

Thanks mate appreciate your support👍🏼

@outlawdingo3020 Год назад

Another tip is if you get new main wheel bearings and it has a little flat disc with it, you bought a gq wheel bearing and that disc won’t allow your bearings to sit properly so throw it away

@ReubsModifications Год назад

Thanks for the info mate, awesome to get some extra tips.

@youngym8823 Год назад

Hey mate, couldn’t you have just punched the whole needle bearing out like you did with the Race? Or nah Cheers

@ReubsModifications Год назад

I had to punch the needles and cage out so that I could get the weld onto the race to shrink it 👍

@tobybarrett144 Год назад

What salient did you use on the spindle?

@ReubsModifications Год назад

I’m assuming you meant to type “sealant” I used blue RTV gasket maker, few different brands you can get but it shouldn’t really matter. As long as it can handle a little bit of heat any sealant should be in the right ballpark 👍🏻

@M.H.F23 10 месяцев назад

What is the parts number of the inner seal.

@ReubsModifications 9 месяцев назад

Hey mate the OEM Nissan part is 40533-01J00 the Trail Safe Seals that I used are 303752-KIT on Superior Engineering.

@TheGeorgecollier Год назад

Where's the d22 sass build?

@ReubsModifications Год назад

Keeps getting put off, I do need to get back onto it though.

@ryan42. Год назад

Don’t ya have to set preload on the kingpin bearings or some shit

@ReubsModifications Год назад

If its in the Nissan manual then I must have missed it, unless you're talking about the kingpin shims. I breezed over them in this video but as long as you put them back where they came from and the knuckle moves freely it should be fine.