Тёмный

HDZero Whoop Lite Digital Conversion | Killed Firefly | DIY FPV Build Story | ELRS Whoop Micro Quads 

Giant Ant Cowboy
Подписаться 4,8 тыс.
Просмотров 8 тыс.
50% 1

A classic coming of age story about a Tiny Quad’s big dreams, untimely death, and miraculous rebirth! Follow FireFly as he struggles with Digital FPV, discovers things don’t always go as planned, and learns the key to success is to never give up.
This build video shows what it takes to convert a FlyWoo Firefly Baby Nano to digital using the HDZero Whoop Lite VTX and Nano Lite Camera. The conversion was supposed to be simple, but there were difficulties disabling the analog VTX which results in a complete rebuild…
If you have any questions, suggestions or advice please share with us, thanks for watching, Cheers!
------- Summary of Video -------------------------------------------
0:00 - Why Upgrade?
0:18 - Chapter 1: "Meet FireFly"
1:00 - Chapter 2: Killed FireFly...
1:25 - Chapter 3: Conversion Plan
1:54 - Chapter 4: "Minor Problem"
2:25 - Chapter 5: "Major Problem"
2:45 - Chapter 6: FireFly is Alive!
3:55 - Chapter 7: 1st Video Thoughts
4:50 - Chapter 8: Analog vs. HDZero
6:20 - Chapter 9: Penetration Test
7:28 - Camera Lens Upgrade
7:35 - Near Death Video?
7:45 - Results, Thoughts, Fun Shots
8:25 - Up Close and Personal
Thanks for watching, please Like, Share, Subscribe, all support is appreciated!
Links and Discount Codes below which also support the channel.
----- Product Info & Links ------------------------------------------
** Let me know if you use these links, so I can give a huge thanks for the support! **
(Don't forget to try the coupon codes.)
- Flywoo Firefly Nano Baby 1s FPV Quad: www.banggood.com/custlink/3Km...
(Coupon: "BGRCDrones6" 6% off)
- Auline 500mAh LiPo 4-pack:
www.banggood.com/custlink/Km3...
(Coupon: "BGRCParts8" 8%)
- Flywoo 450mAh LiPo 4-pack: (** Recommended **)
www.banggood.com/custlink/3Gm...
(Coupon: "BGRCParts8" 8%)
------------ VTX / VRX Antennas and Quad Setup --------------------------------------
- Quad: Flywoo Firefly Baby Nano 1s
- VTX: HDZero Whoop Lite VTX
- VTX Antenna: TrueRC Singularity
- VRX: Fatshark Sharkbyte Model RX5.1
- VRX Antennas: TrueRC X2 Air Crosshairs, and TrueRC Singularity
- FPV Camera: HDZero Nano Lite Camera with 1/2" sensor
- Control Link: ELRS
- GoPro Hero 8 Black with ND Filters

Хобби

Опубликовано:

 

30 май 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 122   
@KaizerTest
@KaizerTest Год назад
The panic on your wife's face at the beginning. Yes lets see the whole video. 👍🍺
@GiantAntCowboy
@GiantAntCowboy Год назад
Omg, it was nuts and hilarious… I figured this tiny quad is pretty easy to fly and next thing I know she’s doing a long-range mission by mistake! Lol I’ll post it soon, it’s a must see video. Thanks for watching, cheers!
@BOTGRINDER
@BOTGRINDER Год назад
wow the amount of work that went into this video, props bro.
@DeeFPV
@DeeFPV Год назад
verry much so
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks man, I spent a lot of weird hours between Midnight - 4am working on this… probably too many, but gotta follow the vision. Cheers!
@dooddrones6521
@dooddrones6521 Год назад
In or out?
@RyanQuellet
@RyanQuellet Год назад
My God, you make some of the best videos. Good work!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks Ryan, appreciate the comment. Always happy to help support the HDZero team. Keep up the good work, cheers!
@baggszilla
@baggszilla Год назад
Awesomeness! I love it! And your wife is Beautiful! Cheers!
@GiantAntCowboy
@GiantAntCowboy Год назад
Hey thanks man, my wife is also very patient and trusting with a open prop quad flying inches from her face. Lol, Stay tuned, cheers!
@Drew_Pearson
@Drew_Pearson Год назад
Okay now I REAAAAALLY want HDZero. Great video man really well done. Also the best comparison I've seen so far.
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea this is a huge upgrade for tiny whoops and Micro quads. Like a complete night and day difference from the before and after shots. Such a pleasure to fly and explore with now. Thanks for watching, cheers!
@TheCarl1206
@TheCarl1206 Год назад
What a nice video, just wow! Thank you so much for sharing.
@GiantAntCowboy
@GiantAntCowboy Год назад
Thank you Carl, happy to help support the HDZero Team. Cheers!
@pacospete4299
@pacospete4299 Год назад
Fantastic Video Presentation !!!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thank you, appreciate the comment. From one Pete to another, cheers!
@eliasbucher6218
@eliasbucher6218 Год назад
That is crazy!!! I would like to see a product like this. Maybe you could ask Flywoo to produce such a product. That would be awesome!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks appreciate the comment. And to your point Flywoo actually did end up making one eventually. (Probably inspired by my video lol) here’s a link: flywoo.net/products/firefly-2s-nano-baby-20-hdzero Cheers!
@eliasbucher6218
@eliasbucher6218 Год назад
@@GiantAntCowboy That‘s very cool!!
@RebelGoatFPV
@RebelGoatFPV Год назад
Excellent video! Both informative and entertaining, nailed it!!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks man, great comment, appreciate the encouragement, cheers!
@doncunningham3124
@doncunningham3124 Год назад
Outstanding video! Unique, entertaining and very informative!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks, really appreciate the comment, took some effort but I had a lot of fun making this episode, stay tuned, cheers!
@sixtofive
@sixtofive 10 месяцев назад
Turned out great in the end!
@GiantAntCowboy
@GiantAntCowboy 10 месяцев назад
Yea, thought it would be simple.. but that’s always how it goes. But it’s a cool little build! Appreciate the comment, cheers!
@0813945668
@0813945668 Год назад
Lovely Video!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks, appreciate the comment!
@danielmccullock1249
@danielmccullock1249 Год назад
Great video Mate! I really enjoy the way you present your content. Can see there is a lot of work gone into it. I just got my Nano lite kit and converted my mob7 which I haven't used in over a year. Makes it so much more enjoyable! Cheers
@GiantAntCowboy
@GiantAntCowboy Год назад
Thank you thank you, appreciate the comment. I always try to make videos a little interesting and had some extra fun with this one! The video upgrade really does make it so much more fun to fly around and explore with these tiny quads. Thanks for watching, appreciate the support, cheers!
@peternguyen3732
@peternguyen3732 Год назад
LOL love the creative edit. Subscribed mate!
@GiantAntCowboy
@GiantAntCowboy Год назад
Awesome thanks, appreciate the support! From one Peter to another, cheers!
@JonathanBirch7
@JonathanBirch7 Год назад
Awesome video. Keep on living your dreams. Regards from South Africa 🇿🇦
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks, always appreciate the support from South Africa! Cheers man!
@trashyLAMF
@trashyLAMF Год назад
Love the video! Also, INCREDIBLE cabin!!! SO jealous haha! Glad to have come across yer channel while researching the HDZERO. Much love and best of luck with the channel!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks, appreciate the support. Those treehouses are amazing. Definitely check out my other videos if curious, happy to answer questions and stay tuned for the next episode! Cheers!
@ironlionfpv
@ironlionfpv Год назад
Super cool video, thnx for the journey 😀
@GiantAntCowboy
@GiantAntCowboy Год назад
Absolutely, thanks for checking it out and commenting, cheers!
@SnakeCakeExotics
@SnakeCakeExotics Год назад
Great story telling
@GiantAntCowboy
@GiantAntCowboy Год назад
Hey thanks, glad to hear my effort was appreciated. Cheers!
@SnakeCakeExotics
@SnakeCakeExotics Год назад
@@GiantAntCowboy was really fun
@JohnCuppi
@JohnCuppi Год назад
Amazing editing and presentation.
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks John, appreciate the comment and support, cheers!
@radholm2628
@radholm2628 Год назад
Cowboy, you outdid yourself this time. Great video! 👍
@GiantAntCowboy
@GiantAntCowboy Год назад
Thank you, Glad to hear people enjoy the effort I put into it. I have a fun time making these episodes, but it’s even funnier when I hear back from the community. Stay tuned, cheers!
@anthonyfpvminiquad1728
@anthonyfpvminiquad1728 Год назад
10/10 video!
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks bud, appreciate it!
@oddeman3489
@oddeman3489 Год назад
det ser virkelig fint ut, jeg liker hva jeg ser,
@GiantAntCowboy
@GiantAntCowboy Год назад
Takk takk! Ja det er en veldig bra FPV system!
@camelisator
@camelisator Год назад
holly shit i did not know HDzero looked this good
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea, HDZero has come a long way over the last year. The bigger Micro V2 camera actually looks even better than this Nano Lite camera. Here’s a quick “DVR Highlight Reel” for example: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5xRpicNfvBI.html Thanks for watching, cheers!
@OVERKILLFPV
@OVERKILLFPV Год назад
Wow wow wow
@GiantAntCowboy
@GiantAntCowboy Год назад
Glad to hear you liked it. Are you doing a simple build?
@winder6
@winder6 Год назад
Wow awesome review you really put that little quad to the test. It's a bummer that the built-in vtx is now in the way of upgrading the quad to HDZERO. I have a BetaFPV Meteor85 I would like to put the HDZERO on.
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks I really appreciate the comment. I’m gonna reach back out to Flywoo and see if they can figure out a proper way to disable the VTX. If you have hot air solder equipment, and better skills than me, you could remove the RTC chip successfully. When I did it I used a big heat gun and accidentally disrupted a bunch of other components… that’s what killed it. The BetaFPV AIO board might actually have a way to disable the analog VTX, I’m not familiar with what board is used in that setup though. Let me know if you figure out anything, and stay tuned, cheers!
@winder6
@winder6 Год назад
@@GiantAntCowboy Thanks for the reply cheers
@gmivisualsjason3729
@gmivisualsjason3729 Год назад
I think this hdzero 1s board/camera is a great achievement. What I'm finding is that yes the up close objects do look very clear. However objects at distance lack image clarity. I've just ordered the Walksnail sytem now that they have a 1s boars so interested to see if walksnail can replace hdzero on my micros
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea, it’s the lens, I tried a couple other M8 lenses and the clarity instantly improved. Didn’t find a good perfect swap though because the small body doesn’t have enough threads to focus some lenses properly. Curious to hear about your walksnail experience, cheers!
@seewell8168
@seewell8168 Год назад
Did you ever find a way to disable the onboard vtx? I'm trying to do the exact same thing with a Diamond ELRS board
@GiantAntCowboy
@GiantAntCowboy Год назад
Basically just destroy the board and then buy one without an integrated VTX, that’s what I did… haha! Unfortunately I never found a solution. If you had a proper “hot air soldering” tool, you could mask the board and remove the VTX chip. Wish there was a simple off switch or setting… thanks for watching, good luck!
@edgaremralino7512
@edgaremralino7512 Год назад
Awesome. Can you pls share the components you replaced on this little one. Also, I'm a DJI system user and what goggles are you using? Thank you.
@GiantAntCowboy
@GiantAntCowboy Год назад
Thanks! The parts are all described in the video, but basically I replaced the FC with a BetaFPV F4 12A AIO board and the VTX is the HDZERO Whoop Lite board and camera. Goggles are HDO with a HDZero VRX module. I’ll be testing the new HDZero goggles next month hopefully depending on production timing. Stay tuned, cheers!
@wilmesz1992
@wilmesz1992 Год назад
I just got the mob6 hdzero, man I had no idea a 1s HD tiny whoop could be this powerful. I wonder if the crazy bee fc that's on those would be a good candidate for the firefly? At least that would take care of the analog vtx issue and I think be a lot lighter than the betafpv solution.
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea these little quads are some much better with HD video! I’ll look into that FC for my next build. Thanks for watching, cheers!
@stevenedwards408
@stevenedwards408 Год назад
hey man could you do a vid on your findings with changing lens out on whoop lite cam, the snippet you showed looks really promising but I'm nervous to try without a bit of guidance. Great vid as always
@GiantAntCowboy
@GiantAntCowboy Год назад
Hi man, so I haven’t made any progress with that swap yet. The lenses I have won’t focus unless they are barely screwed in, so I need to find a different solution. As far as how to do it, the lenses just screw out, and then screw back in, at which point you’d have to look through the goggles and focus the image. The thread is an M8 so most nano lenses would fit. If I find a good solution I’ll definitely share with that community. Appreciate the comment, cheers!
@stevenedwards408
@stevenedwards408 Год назад
Thanks for taking the time to reply, I hope you do get around to achieve this, can't find any other info on doing a lens swap on this camera so you would be the first I guess. Thanks for the info on what you've tried so far and the thread size... maybe I'll have s go just scared of breaking my camera as I'm sure you are 😆 👍🏻✌🏻
@GiantAntCowboy
@GiantAntCowboy Год назад
@@stevenedwards408 sure thing, removing and installing the lens is actually super easy, it’s literally just a screw in/out lens on this camera. Just avoid touching the back of the lens and the image sensor. You can clean them, but it’s best to avoid. Screwing the lens in and out is how you focus it, which you’ll have to do if you remove it, and even factory lenses can be out of focus so it’s worth checking periodically.
@dooddrones6521
@dooddrones6521 Год назад
Great work as always man! That first AIO board may simply have not been able to handle the heat put into it after removing both of those chips. I'm not sure why they didn't tell you to simply cut the trace suppling power to the chip with an x-acto knife
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea, it’s a bummer that there wasn’t a simple solution… thanks for watching, appreciate the support, cheers!
@azimyth1542
@azimyth1542 Год назад
Does the ELRS 2.4ghz interfere with the HDzero system?
@GiantAntCowboy
@GiantAntCowboy Год назад
No issues with anything close-range. On my long-range setup though I seemed to be getting some interference and ended up moving the ELRS RX/Antennas to the front of the quad. No problems since, BUT the initial problem could have actually been an environmental issue… (WiFi, Cell tower, and high tension power lines were all around my test location). Either way it’s always best to separate radio/electronic equipment whenever possible, especially for long-range builds.
@jaysonrees738
@jaysonrees738 Год назад
Good grief, that looks even better than my setup with the Race V2 and Micro V2 camera. Makes me wonder if I have some fine tuning to do somewhere. Really cool video!
@GiantAntCowboy
@GiantAntCowboy Год назад
It’s really on par with the Micro v2, except the smaller lightweight lens have some hazing/haloing in bright conditions as I showed in the video, but ultimately I couldn’t believe how good it looked either when I first started using it. Amazing achievement for only 8 grams! Thanks for watching, stay tuned, cheers!
@jaysonrees738
@jaysonrees738 Год назад
@@GiantAntCowboy Looking like my VTX is probably defective. No wonder yours looks better!
@GiantAntCowboy
@GiantAntCowboy Год назад
@@jaysonrees738 you’re Suros on the IntoFPV forum maybe?
@jaysonrees738
@jaysonrees738 Год назад
@@GiantAntCowboy You are correct. Guess I didn't even consider that you were over there too. But yeah, according to Ronin, he's seen plenty of defective unit reports, whereas I can't find a darn thing. Hopefully such issues become less common, as this is currently the digital system I most want to see succeed. Both the company and the system have been amazing.
@GiantAntCowboy
@GiantAntCowboy Год назад
@@jaysonrees738 oh yea, I’m everywhere and see everything… lol. Have you reached out to the HDZero team yet? Or the retailer you bought it from? Agreed, we all want HDZero to grow, evolve, and succeed.
@pacospete4299
@pacospete4299 Год назад
I'm new to fpv and i just bought a Cobra x box goggles . What i see is a nice image down a tunnel , like watching a TV set in a dark room . What i would like to know is with a pair of say FatSharks or DJI goggles will i see an image " closer " to my fov and not the tunnel effect ??? i do not know anyone who has goggles.
@GiantAntCowboy
@GiantAntCowboy Год назад
With box goggles yes, it looks like a tv down a tunnel. This is because it’s literally one large screen set far enough away that you can focus on it. With binocular style goggles you have two small screens, and the “darkroom/tunnel” effect is reduced significantly. At some point you can upgrade to a set of binocular goggles and keep your box goggles for spectators, or co-pilots. Search the classifieds, eBay and Craigslist for good deals. A lot of people sell decent used stuff, 90% of the FPV equipment was bought used. Thanks for watching, cheers!
@maddercat
@maddercat 9 месяцев назад
Is one of those 4 pins also a vtx out on this board? I'm having an issue where my video will go out when I'm above 75% throttle and want to use an external vtx to see if it fixes the problem. flywoo are being jerks...saying my battery voltage is too low, but the quad is still flying so...???
@GiantAntCowboy
@GiantAntCowboy 9 месяцев назад
I’ve had the issue Flywoo is mentioning in the past, however mine was a custom build with a separate VTX. The fix was to wire the VTX to VBat because the 5v pad didn’t supply enough power when throttling. Is yours a BNF? Or a custom build? Does the DVR footage show voltage dropping hard before the VTX cuts out? Let me know.
@maddercat
@maddercat 9 месяцев назад
@@GiantAntCowboy No, I have the one with the on board vtx right.. No it's a constant voltage I can put a new battery on it, and blip it and the video will go out above 75% throttle, so I want to disable the on board vtx and put an external one on it and see if it fixes it but I need a vtx out pad right, which you needed too? but no one says where that is? It's not on any diagrams I can find. I assume it's one of those 4 pads? yes mine was a bnf, but I've completely torn it down now multiple times trying to figure out this problem.
@maddercat
@maddercat 9 месяцев назад
How do you wire the vtx to bat? Is one of those pads the vtx power? The bat is lower voltage though, but I guess would give more amps? I think I would want to wire it to the 5v rail maybe which should be 2amp? Whatever rail its on rn isn't sufficient obviously, unless it's the camera which is shutting down but I don't think it is.@@GiantAntCowboy
@GiantAntCowboy
@GiantAntCowboy 9 месяцев назад
If you go to the 1:40 mark of the video i show where I wired the HDZero VTX. I used the 5v pad, but was losing video too I believe. You can use the VCC for direct battery power which should give more amps. (Try both maybe) The board in mine was the “goku versatile f4” if you search that there are some diagrams available I think. Ultimately as shown in my video I killed the board and replaced it with a completely different one. Hope that helps, but let me know.
@maddercat
@maddercat 9 месяцев назад
I'm thinking right now it's a heat issue.@@GiantAntCowboy
@Braincho
@Braincho 9 месяцев назад
Help please! I got Flywoo 1.6" and Radiomaster Boxer. I did flash Boxer with EdgeTX and ELRS and adjusted Models. On the drone flashed ELRS and binded RX to TX, also added arm/disarm switch and air/horizon switch. Everything looks working - drone does arm/disarm, but when i tilt the drone slightly(without props - just tested on the bench) motors start to spin faster and/or slower and if tilt bit more - it disarms. Also when i throttle up and motors start to spin faster and get themselves fixed in a constant high speed and the trottle gimbal doesn't affect it anymore(not working) - the disarm switch still works. Could you help me please? What can i do to fix it?
@GiantAntCowboy
@GiantAntCowboy 9 месяцев назад
So believe or not this is normal behavior. Without props your quad can’t control it self and is constantly trying to fight the movements you’re making with your hand. Additionally you probably have “AirMode” turned on, which is why the throttle goes up high and stays there. Again you quad is trying to adjust itself but can’t without props. As long as Arm/Disarm work I’d suggest you put the props on (in the correct direction) and Arm the quad somewhere safe. It’s probably perfectly fine but of course be prepared to disarm in case… Let me know if it works out. Cheers!
@Braincho
@Braincho 9 месяцев назад
Isn't airMode - ACRO ? i think i need it if its the one. why it should be off?Will test it tomorrow as well as adjusting Video and will let you know the outcome.@@GiantAntCowboy
@GiantAntCowboy
@GiantAntCowboy 9 месяцев назад
@@Braincho hey, AirMode is different than Acro mode. AirMode allows the quad (PIDs) to make bigger corrections at lower throttle positions and it is better left On. But, if you want to test the quad without props then Turning AirMode Off can make sense. You’ll find the AirMode ON/OFF option in the BetaFlight Configuration Tab about half way down, you can also assign it to a switch if desired. However, you can just put props in this quad and do a test flight. I’m sure it’s fine. Also such a small quad isn’t really dangerous if something goes wrong.
@Braincho
@Braincho 9 месяцев назад
@@GiantAntCowboy Adjusted Gimbals and video +OSD and tested the quad with props in Sigh of View over the bed and it flies, not sure the mode(horizz or angle) i flew it in a small space. Will test outside soon. Btw, i barely put the 750mah battery in the battery strap. And the strap doesn't want to go out. Thanks for all the help provided!
@GiantAntCowboy
@GiantAntCowboy 9 месяцев назад
@@Braincho glad you got it sorted, happy to help. Cheers!
@lionelfrenchface
@lionelfrenchface Год назад
Cool idea. I've the same quad. Would like to know how much did the conversation cost?
@GiantAntCowboy
@GiantAntCowboy Год назад
This ended up being a whole rebuild since I couldn’t get the analog VTX to shut off… I’m gonna reach back out to Flywoo and see if they can figure out a proper way to disable the VTX. If you have hot air solder equipment, and better skills than me, you could remove the RTC chip successfully. When I did it I used a big heat gun and accidentally disrupted a bunch of other components… that’s what killed it. Anyway to your question, the HDZero Whoop Lite VTX and Camera kit is $99 and the BetaFPV AIO board I used is like $50, so all said it cost around $150. Thanks for watching, let me know if you have any conversion success, cheers!
@lionelfrenchface
@lionelfrenchface Год назад
@@GiantAntCowboy thanks for getting back to me. My biggest problem or more question is which digital system to go for. All my stuff is analog ATM. So I'm trying to decide which digital system to go for.
@GiantAntCowboy
@GiantAntCowboy Год назад
@@lionelfrenchface ah yea, there’s really no right answer here… I too came from analog and decided to try HDZERO because of a few things: 1) I already owned HDO goggles and could easily add the HDZero VRX to them, which was cheaper than buying brand new DJI 2) Since you have the same goggles you can continue flying your analog quads, as well as use the same antennas 3) I do a lot of longer-range stuff and liked that HDZero was a “receive only” system, meaning the goggles and VTX are not linked together. This is good because if you lose signal it can come back quickly without a rebinding process like DJI, which can freeze and reboot. 4) HDZero is more customizable, and has* multiple manufacturers and vendors, a solid community, and the company actively engages the community all the time. * I starred (*) multiple manufacturers because HDZero is still relatively new and the system is quickly evolving, because of this there has historically been lower levels of production and availability; Covid and manufacturing shutdowns in China didn’t help this over the last year either… but larger companies are starting to prototype HDZero equipment (Foxeer for example) and HDZero themselves are even developing a seemingly very impressive goggle specifically for the system. - DJI is a great “plug and play” option but can be more expensive, depending on if you currently have decent goggles. - DJI does have better image resolution and arguably better penetration, but it does both by broadcasting and re-broadcasting video signals. This can cause slow (high latency) blurry video feed when signal gets bad. Where as HDZero maintains consistent resolution and latency but shows static like classic analog. - DJI doesn’t support Canvas mode so you have very limited OSD elements and they are not recorded to the DVR, which is another issue for longer-range type flights… Then there is Walksnail or Fatshark, but no one really knows what’s going on there yet… So hopefully my long-winded response provides some helpful insight for your decision. If you have follow up questions let me know, cheers!
@nikodelrey
@nikodelrey Год назад
Nice bike! Honda VFR750?
@GiantAntCowboy
@GiantAntCowboy Год назад
Yes sir, good eye! It’s a real solid beast, gotta love that V4 engine rumble, one of the few bikes I have left still.
@nikodelrey
@nikodelrey Год назад
@@GiantAntCowboy I miss my VFR800, yep loved that V4 engine rumble.
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea great bikes. I feel bad because I’ve barely ridden it this year… been super cold and rainy here in Norway. Complete opposite weather the rest of the world seems to have! Lol
@camdynkellett6782
@camdynkellett6782 Год назад
Great video, but I would be lying if I said that I knew what the video was about looking at the title and thumbnail...
@GiantAntCowboy
@GiantAntCowboy Год назад
Appreciate but the compliment and feedback. I 100% see your point and may make some adjustments to either the image or title. Are you a subscriber, or did you just click the Thumbnail out of curiosity? Cheers!
@ianwalton284
@ianwalton284 Год назад
Or you can get the new 2s baby firefly
@GiantAntCowboy
@GiantAntCowboy Год назад
Sure, but that wasn’t an option when I did this video. Ultimately this was just for fun though anyway. Thanks for watching, cheers!
@ianwalton284
@ianwalton284 Год назад
@@GiantAntCowboy wish I had your soldering skills. Have to work on that when it's raining.
@Daddyfly_FPV
@Daddyfly_FPV Год назад
My firefly is sitting on my desk. He hasn’t flown in a while. He’s a little fucked up
@GiantAntCowboy
@GiantAntCowboy Год назад
Projects easily get “back burnered” in this hobby… I have a handful of projects needing attention. Thanks for watching, cheers!
@MrBrettStar
@MrBrettStar Год назад
That price though 😞
@GiantAntCowboy
@GiantAntCowboy Год назад
Yea, this whole hobby costs a ton of money… ugh. “Cool Costs” my father always said growing up. Thanks for watching, cheers!
@MrBrettStar
@MrBrettStar Год назад
@@GiantAntCowboy whoops were a cheap alternative… still can be I guess just have to accept compromises. Still liked the video by the way
@GiantAntCowboy
@GiantAntCowboy Год назад
@@MrBrettStar for sure, digital is not necessary, but it’s nice to have the option now. 👍
Далее
▼ОНИ ЩУПАЛИ МЕНЯ 👽🥴
32:00
Просмотров 514 тыс.
Which bus driver am I?🚌
00:13
Просмотров 1,5 млн
The Best 1s Micro Drone - Firefly 1S Nano Baby
33:58
Просмотров 26 тыс.
HDZERO 1S WHOOP LITE KIT - DIGITAL FPV FOR EVERYTHING
22:14
I made my OWN Apple TV-with a Raspberry Pi
16:12
Просмотров 78 тыс.
I Turned 1-Star Toys into Military Nightmares
19:32
2D water magic
10:21
Просмотров 201 тыс.
CJ попал в GTA V 😂
0:28
Просмотров 2 млн
Проверил, как вам?
1:00
Просмотров 1,8 млн