Тёмный

Honda GC190 Carburetor Clean - Won't Start? 

Hank's Garage
Подписаться 47 тыс.
Просмотров 18 тыс.
50% 1

Due to factors beyond the control of Hank's Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Hank's Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Hank's Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Hank's Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Hank's Garage.

Опубликовано:

 

6 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 12   
@9mmTXn
@9mmTXn 5 месяцев назад
I had a stuck emulsion tube as well. Put the carb in my Hornady ultrasonic cleaner with some simple green for a cycle. Followed up with some carb cleaner, then put the jet back in and applied a little torque. Removed the jet, and the emulsion tube broke free super easy.
@lawrencecarroll2031
@lawrencecarroll2031 Год назад
I use 6m threaded rod to make disassembly and reassembly easier on that carb. Take one of the bolts out, thread rod in, take the other bolt out, thread 2nd 6m rod in. You can leave them in if you want and just secure carb with 6m nuts or remove them one at a time and reinsert long bolts. Good video
@Rustycam1025
@Rustycam1025 8 месяцев назад
Yessir! I do that as well. Makes it so much easier to slide all the various gaskets and spacers on there one at a time.Everything stays in place.
@Bobcagon
@Bobcagon 5 месяцев назад
Ya I saw some dude doing that on a Honda vertical and thought what a great trick. This guy makes it look not too bad but anyone who has worked one of these knows better.
@Bobcagon
@Bobcagon 5 месяцев назад
Anyone know the pre symptoms of the fuel going on these? Or does it just quit….then nothing?
@brianking1138
@brianking1138 Год назад
I can usually get the emulsion tube out by pressing from the top with an Allen wrench. Sometimes they won't budge.Don't forget the pilot jet under the plastic cap.
@SwimFlySwim
@SwimFlySwim 7 месяцев назад
I had my carb cleaned, ran when I got it back from shop. Ran it. Ran it completely dry as we’ve had problems in past with stale fuel. Filled it with new fuel today and the f’ing thing again will not start. I’m about to just give up on it. Spends more time in shop than in use.
@mitchrenee
@mitchrenee 4 месяца назад
Thanks great video
@velbarker6203
@velbarker6203 7 месяцев назад
Не стабильные обороты на данном двигателе что посоветуете?
@joblessalex
@joblessalex 3 месяца назад
Fuel pump on a carbd motor? Wtf?
@hanksgarage_
@hanksgarage_ 3 месяца назад
YUP!
@queenstownkid
@queenstownkid 7 месяцев назад
i dont like that carb setup
Далее
Fake watermelon by Secret Vlog
00:16
Просмотров 6 млн
A Carburetor Fix Many Mechanics Don’t Know!
9:26
Просмотров 184 тыс.
Full Detailed Honda GCV160 GCV190 Carb Clean [4k]
22:48
How to clean a Honda EU3000is carburetor.
15:01
Просмотров 92 тыс.
Honda HRC216 No Start: GSV160 Carburetor Clean How To
14:54
EASY FIX/Honda Pressure Washer No Start
11:28
Просмотров 42 тыс.
Fake watermelon by Secret Vlog
00:16
Просмотров 6 млн