How to apply  

Thanks for watching! No argument from me about use case, this is a product that needs a certain environment and application to perform well. As meguiars have said, they consider it to be a true coating, not a spray coating which is why the application is not as straight forward like the packaging would imply. I will say that after applying it, I don’t find it to be that intimidating, especially when compared to other true ceramic coatings. If I had to choose between the application of this vs. Cquartz lite, I would take this based on my experience. Easy to spread and work (maybe I made it look harder than it is, my bad), and once you work in and breakdown the product, its wipe off is great. Whether or not it will last like Cquartz lite is another story, but if it does, I could see myself adopting this into my routine. I do think that they should have released this under their professional lineup though, as an entry level version of M888 as it does need be handled and applied like a professional product. Depending on the cost factor, I would encourage those with the setup required to apply this product to give it a try, once we have a better durability estimate. I plan on revisiting this product later on when temperatures are better and I can get it into sunlight to help curing to see if there is any more performance to be gained.

Its not anymore work than any true ceramic coating.

Tried and true, will still provide tons of use for even experienced detailers.

Interesting. How old was the product you applied it to? Sometimes once the initial layer is gone, a lot of products can apply to a coating below.

A few months ago I applied the Cerakote rapid ceramic spray coating and have used meguiars pro m799 ceramic bead booster a couple of times. The undiluted version of the hybrid ceramic detailer. Green bottle. I love that product especially in the pro version.

What did you think of rapid ceramic after some time on the car?

I don’t use any top up products during my real world durability tests as I want to see when the base product fails. I understand with coatings there is a trade off in slickness without top ups some times, but I want to see baseline performance.

Which of you think about it, lends more weight to meguiars saying it’s a proper true coating that can be sprayed. I will say that my paint was bare in both applications, as Cquartz lite bonded no problem first attempt. That supports the other half of it being improper application.

@@sheepstardetail That's a good point. Honestly I think Meguiar's is going to have a tough time with this product in the market. Because most average consumers will assume it's just another spray and wipe. A lot of them won't even prep the paint, let alone wipe until residue is completely gone. I wouldn't be surprised if this ends up being discontinued like the Hybrid paint coating (which was an excellent product) but the average joe simply did not understand what it was, and how best to apply it.

@@soapa4279 agreed. They should really market this under their professional line as a quick and decent entry level coating for M888.

More than likely seeing the detailer, as it has decent legs on its own. I really like the hybrid ceramic liquid wax, even if it only lasts 4-6 months, it can be easily maintained with both hybrid ceramic wax and the hybrid ceramic detailer, and it’s effortless to reapply for a liquid type sealant.

Haven’t used that one yet, but physically, this isn’t hard to spread, buff, or wipe off. It’s just a few more motions than you’re used to, and some specific temp requirements. I personally think the temperature requirements are going to be the part that hangs up a lot of folks.

@@sheepstardetail Oh dude you gotta try HPC. It's one of the easiest and enjoyable coatings to work with.

@@soapa4279 I’m yeah I know, I’ll see where I can get my hands on it. Would be a good head to head against ultimate ceramic coating.

​@@sheepstardetailPersonally I think HPC wipes tge floor with this stuff. Hydrophobic properties on HPC are on another level than this. Plus I believe it's way more durable.

HPC has been discontinued

Haven’t tried much from fireball, but their spray on coating/protection is quite good!

I have seen that, haven’t heard much about it but it’s not terribly expensive

Definitely polish and panel prep for best results. Sometimes if the paint hasn’t had wax on it in a long time, products will apply and bond, but I would rather seal in nice polished paint over oxidized and swirly paint.

Besides the temperature requirements, application is actually quite easy. It applies and spreads nicely, and once you buff it down (which doesn’t take quite as long as I showed here, I just had a bit more residue than a normal panel size would have) the flip and wipe off is quite nice. The really troublesome thing is the temps, some people don’t have indoor working environments. Also, we don’t yet know the long term performance for this products, so it could be a legit solid 6months which isn’t bad overall.

It's easier than glass bottle coatings..

Time will tell for me. If it has the legs and lasts in the real world, then I can consider it a win compared to products like Cquartz lite as it is still easier to work with.

I have a fair bit for sure. I did purge some old and no good products recently to make room.

@@sheepstardetail how do you know when they are no good ? How long do they usually last ?

No good means I didn’t like it/will never use it even to make a video crapping on it, or it physically has gone off like some coatings. Some products were so old that even if they were good, they were less than half a bottle and I really do don’t like it.

80 degrees Celsius?!😉

@@herts30yeah I may forget to switch units from time to time.

100%. I also think launching it under their consumer line was a mistake.

I would say jumbo’s is sheeting, meguiars is beading just fine.

You do the same process as most sprays, but you have to wipe it in very thoroughly until the residue is basically gone. It needs to be worked in almost like a polish. If you don’t the curing process doesn’t start as the part that needs to be exposed to air stays encapsulated and rinses right off.

@@sheepstardetailThis is the best explanation so far

They released a video a couple weeks ago showing the application process, basically you need to buff it until the residue is nearly gone. Because I’m working in a small test area, that meant a couple more passes as one spray could have done a larger area.

Prime the cloth with product (one good spray) and you’ll basically fix that issue. Not trying to defend megs or anyone else, but most of the time when people have really inconsistent results with wipe on wipe off protection products, 75% of the time it’s because the cloth being use to spread the product it’s primed.

I’m not sure yet. I’ll be doing some more testing once the weather warms up so I can get the most consistent results.

I think it’s really the only way to make a true wipe on coating in a spray format that doesn’t eat triggers or go off prematurely.

@@sheepstardetail hopefully it lasts. We have a really good sealant over here that does well over 12 months and outperforms CanCoat - doesn’t eat triggers or go off prematurely, but doesn’t offer hardness. Will be interesting to see how it holds up.

Which product is this?

@@sheepstardetail SiRamik Lustrous Plus Graphene Spray Sealant. Infinity Wax’s Synergy Lite offers a different alternative - the ability to coat outside and be weather ready in an hour, though will block sprayers so its best to spray panel wipe through it when used.

@@roscopervis oh yeah, heard about that on detailing world. Never seen it available to me without my yearly income worth of shipping and duty.

Not telling… yet.

Ease of use can wear many hats. Some people are feel waiting for a wax/sealant to haze up before wiping as “hard to use”. This needs a bit more buffing for sure, but it’s still slick when doing so and final wipe off was effortless once you break it down.

As long as you use a good quality microfibre it’s not that bad. It’s at least easy to wipe in, and very easy to do the final buff on that I overall feel it’s not something that would deter me from using it. Seeing how long it lasts is what is going to make or break the product for me.

Nu Finish graphene coating will handily out last Seal & Shine in the real world. More testing required with megs to see its best performance, I am still optimistic but we’ll have to wait and see, I am waiting for warmer weather before I retest it.

Hmmmmm never used the nu finish graphene spray. I might get a bottle and put it on my girls car to try it out. I use Adam’s advanced graphene coating on my car and top it with the advanced graphene spray coating every two months. I wash my car every week using carpro reset and use the Adam’s graphene detail spray when I dry it off. There’s something for everyone out there. You just have to find something you like and use it correctly. Nothing will work well if you have bad paint. That’s why paint correction is so important before you apply anything the first time.

It’s not actually that bad, Cquartz lite is far more effort to remove than this is to apply and remove. Whether or not it lasts as long, is still the question.

It’s definitely not at Cquartz lite or mystery product levels.

Yeah I’m not really sure how the price translates as it’s not for sale in Canada. I will retest it once it warms up and application/curing isn’t as troublesome.

Are you the person that said that before? Stop it I’m going to get sued.

@sheepstardetail probably... it just struck me again... I like your content...good stuff

You need better cloths.