Тёмный

How to install a new water main line and shut off valve 

Budget Plants
Подписаться 32 тыс.
Просмотров 131 тыс.
50% 1

Step by step video of my DIY new water main line and shut off valve... for under $300! PLUS...install a hidden hose bib!
I had to replace my old galvanized water main line and leaky shut-off valve before I could move forward on my landscape project. I cut out and removed the valve and galvanized water main line and installed a brand new pipe and valve. BUT I didn't use copper! I actually used PVC schedule 80 pipe instead! This is much easier to work with than copper pipe as you don't have to sweat joints, and it's MUCH cheaper! This is a great money saving material as copper pipe is SUPER expensive.
I also go over how to make a pressure shooting water jet device to tunnel under walkways and hardscape to get your pipe through. We also look at the best methods to trench through lawn and ground cover so it looks nice and neat when you put it back.
One of the extra little goodies we look at is how to install an underground hidden hose bib or water spigot. It's simple, cost effective, and incredibly convenient!
We also look at the water meter and understand what the individual components are. The city has a service shut-off valve, then the actual meter itself that displays how much water is being used, and sometimes there is another valve after the meter that is used to shut the house water on or off.
We also review the benefits of using a union coupling in the main line. This is a nice component to use in case a break or leak occurs down the road and you had to make it a repair or remove a section of pipe. It makes it much easier to disconnect a section and replace while making fewer cuts in the pipe.
We also look at how to set up irrigation valves and connect those to the main line. It's often times beneficial to have a secondary shut-off valve that allowing you to isolate the irrigation valve manifold in case you ever needed to change them out or do a repair on the valves. This way you don't have to shut off the whole house water. You have a separate isolation valve dedicated to the irrigation system.
With this step by step DIY tutorial video, anyone can install a new water main and shut-off valve with a little elbow grease. And it doesn't have to cost a million bucks! These materials are very cost effective and a great cheaper alternative to copper pipe. And no sweating necessary! On the joints at least :)
Thanks for watching!
Dom
- - - - - -
Music credits:
Intro
Original music by Dominic Masiello
Time Spent
Evolv
Summer Bluet
Isaac Joel
app.soundstripe.com/songs/7456
Mountaintop
Hawksilver
Classy and Sassy
Falls
app.soundstripe.com/songs/6548
Sky
OBOY
app.soundstripe.com/songs/7474
Nice Vibes
Neon Beach
app.soundstripe.com/songs/9481
Purple People Tweeter
New Wave Sounds
DISCLAIMER: Dominic Masiello and/or Budget Plants and any of it's sponsors, partners, or associates are NOT responsible for any damage done to a property of which the plumbing wasn't done by a professional, I do not recommend doing your own plumbing if you are unsure about what you are doing, always hire a LICENSED contractor when doing any type of plumbing so you can be covered by insurances if something does happen, these videos are for entertainment purposes only!

Хобби

Опубликовано:

 

5 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 155   
@19moods
@19moods Год назад
This was so helpful. I have a leak in the drain pipe going to my house and this basically showed me Everything to do . I have a bad back and want to use my pressure washer to loosen the dirt and shop Vac to suck it up. Problem is the pipe to the house leaks A LOT. Lost 5k gallons in 16 hours. Is it ok to connect my Pressure Washer directly to the meter?
@min2oly
@min2oly Год назад
I was just quoted 4800 for this! Thanks for sharing, I'm going to do it myself. I have almost the exact same situation. THANKS!!!!!!
@YB-eg3rj
@YB-eg3rj Год назад
Use map gas torch to break those seized up joints. Heat moves everything, dead or alive
@ActuallyCasual
@ActuallyCasual 2 года назад
This video is so underrated. My only critique is... Hydro excavating under the walkway is a great idea unless YOU DONT HAVE WATER!! 😂😂 Oh well, I'll just dig.
@gordonmack7766
@gordonmack7766 Год назад
thx for this vid. just closed on my first house 2 months ago, a 70 year old rambler, and the plumbing problems began almost right away. your tutorial saved the day for me.
@BudgetPlants
@BudgetPlants Год назад
Hey Gordon, wow that’s music to my ears.. so happy my vid was helpful!! And thanks so much for the wonderful comment. Congrats on the new home!
@dwhitney1000
@dwhitney1000 Год назад
Wow I wish my soil was like that to dig. Our valley is FULL of rocks. Nice info.
@BudgetPlants
@BudgetPlants Год назад
Hahaa yeah I got lucky on this one lol
@zacinnc78
@zacinnc78 11 месяцев назад
me too brother every time i put the shovel in the ground i hit one
@caseymoeller8896
@caseymoeller8896 Год назад
I just had a bid to replace my old galvanized main line for $8500 😳This was such a helpful video. Thank you!
@BudgetPlants
@BudgetPlants Год назад
Awesome!! Glad to be of help :)
@HRTsAFyre
@HRTsAFyre Год назад
Wow that's expensive and very scary
@Izaik
@Izaik Год назад
Probably because you have or the company thought you had Service Line Warranties of America (SLWA) coverage. They will cover up to that EXACT amount if repairs or replacement is needed on your supply and/or sewer septic lines.
@francesmcphail7601
@francesmcphail7601 11 месяцев назад
You think that's expensive..3 different companies wanted 3 different prices starting with $1,600 to $2,900😮😭😭😭 I'm almost 73 & my husband is 75 I saw your Video and I'm going to try this project on my own..the digging is going to be the hardest part..wish me luck🤞.
@BudgetPlants
@BudgetPlants 11 месяцев назад
Awesome!!! Give it a shot! Just maybe get some help with the digging part.. that’s always the worst 😎
@JRJUNIOR215
@JRJUNIOR215 13 дней назад
GREAT JOB THANKS FOR EDUCATING ME....AWSOME
@mikeboe1871
@mikeboe1871 Год назад
I'm old school and would have stuck with type k soft copper. No soldering as you mentioned. It is connected by flaring with brass nipples and adapters. It's stronger and will last almost forever. Also on the riser/pipe from the ground to house, sleeve the pipe with another pipe to protect the exposed pipe from physical damage.
@oztauge5471
@oztauge5471 Год назад
I’m young and inexperienced, but can you explain why k soft copper is a better alternative? I know it’s stronger, and arguably more durable, but isn’t copper more vulberable to ruptures under freezing temperatures?
@cornpop7805
@cornpop7805 Год назад
I personally wouldn't use PVC as a pipe for domestic water use, I believe that polyethylene is produced using far more inert chemistry, my concern being chemicals leaching into my drinking water. I'm currently installing a 300' water main and using what the professionals use (when they aren't using soft copper coil), "SIDR-7 polyethylene roll pipe" (some use SDR-7, which is a little smaller per trade size). There are different sizes of SIDR-7, I'm using 1". Another great benifit of SIDR-7 pipe is it comes in continuous rolls, so my entire 300 ft length, will have no joints, except where it connects to the meter and inside my house. The compression fittings can be a little hard to get for homeowners (as they might have to source them from a pro supplier), most people use barbed bronze fittings and ss hose clamps, which are cheap enough to buy. However, I'm using the compression connectors because they do not reduce in diameter. The pressure drop charts I've seen show that SIDR-7 pipe can carry about 2x the volume of water as the the same trade size copper, SCH 80 PVC can carry less than copper. 1" SCH80 PVC carries a volume somewhere between SIDR-7 1/2" and 3/4". While the SIDR-7 pipe is much cheaper than copper or SCH80 PVC, the compression fittings for SIDR-7 pipe are like $60 for straight fittings and $150 for tees. In my case, I only need one straight fitting because the utility company will attach their end with their fitting and I'll attach my end to a ball valve, then convert to PEX-A inside the house. From inside the house, I'm using 1" to feed several outside spigots for our various greenhouses and animal pens. So, the approximately double volume of water will come in handy because the home's water pressure won't drop as much when a garden hose (or 2) are being used outside. The truth is, the best way to maintain water pressure, is to maximize water flow, by using the largest pipe that is practical for the application. (Don't oversize hot water because it wastes more hot water). It still would have been less than $300 to use 1" SIDR-7 and compression fittings for his project. I'm certainly not saying he messed up, I think he did a fine job for a homeowner. But, anyone that has worked professionally installing water mains, is going to choose copper coil, SIDR-7, or SDR-7 roll-pipe to feed their house or business.
@simpleman5541
@simpleman5541 Год назад
would you kindly provide some of the links for the roll and fittings? I need to do something similar 300'+ with 3 T fittings. Some plumbing company came out yesterday and quote me $36,198 for the job using black Polyethylene and when I asked about the connection he said they heat it up and it bonds.
@cornpop7805
@cornpop7805 Год назад
@simple man Tell more about the project first. Is this tying directly into the municipal water tap? That's why I had to use the exact pipe that I used. As far as I know, all municipalities have particular specs for what pipe to use, and they're very strict about it.
@cackleberryfarm4598
@cackleberryfarm4598 Год назад
Wow! A LOT of VERY impressive helpful hints I wish I had known about for all the years I have had to do similar projects. But know now moving forward for up coming biggest project I've had to face. Finding the main and digging WAY down to it in rocky sandy soil about 6' deep!
@filter4now
@filter4now Год назад
Always been a "just do it" type of guy. The only thing that truly makes something impossible is to believe that it is, right? I realized how lucky I was sometimes. There was a hose bibb / spigot in line with a galvanized main like you put in. The tee was 50 years old galvanized pipe trying to fix the leaking spigot. Tried unscrewing the spigot - it unscrewed underground. That was one of the worst experiences - dirt falling in the female trying to make it a non-leaking join. Got home depot to hate me then running in at 8:58 while assuring my parents "no, you're not going to have to pay $10 grand"... (crap...) finally got it but later was thinking "oh man... had that tee cracked?" Anyway, certainly agree with you about galvanized :)
@garyrandalls853
@garyrandalls853 2 года назад
I am the Plumber/Fitter Man. Hear me. The dielectric coupling is a union. By its nature, they are expected to leak. By code, you need an access panel. You can't just bury them! You want an easy fix? Installing 6" of brass (like in a threaded nipple) to break the electrolysis, will work.
@tb6791
@tb6791 2 года назад
Another good tool similar to the nozzle blaster you created. Use a piece of schedule 80 or 40 and cut it at an angle, which you can use for deep root irrigation. You'll be able to penetrate under the rootball underground it works great for new plants and trees🤓
@johnvitz310
@johnvitz310 10 месяцев назад
So nice when you don’t have to worry about freezing, Nice job
@BudgetPlants
@BudgetPlants 10 месяцев назад
Thank you!! Yes, luckily that’s not an issue here.
@damarpo5467
@damarpo5467 2 года назад
Awesome job! Love the sch 80 pipe!
@BudgetPlants
@BudgetPlants 2 года назад
Cheers!!! 🍻
@ucmmar
@ucmmar Год назад
You inspired me. I've already dug the trench. I just need to tunnel under the concrete slab.
@BudgetPlants
@BudgetPlants Год назад
SWEET!! Good luck on the project 💪😎
@ucmmar
@ucmmar Год назад
I did it! I replaced my water main line. I had a lot of small rocks while tunneling, but the tunneling thingy was strong enough to push them out of the way.
@BudgetPlants
@BudgetPlants Год назад
Woohoooooo NIIIIIICEEE!! You just saved yourself thousands 💰💰💰 Well done 👍🏼
@squishybrain
@squishybrain 2 года назад
This was one of the best videos I've seen on how to lay in a main line. Gave me all the info I needed to feel confident I could tackle this myself. Also, wow! The method you used to get a hole under the sidewalk! I had no idea and was dreading the thought of digging under manually. Thanks!
@BudgetPlants
@BudgetPlants 2 года назад
Wow thanks for the kind words!!.. I SOOOO glad I could help by sharing a bit of knowledge. I wish u well in your project! Please feel free to hit me up with any questions as you go along. Thanks for watching!! - Dom
@russellrogers5111
@russellrogers5111 Год назад
​@@BudgetPlants 990
@olizk
@olizk 2 года назад
Good entertaining video with helpful info.
@cesarespinoza5256
@cesarespinoza5256 2 года назад
Definitely the best how to video for main water line install. I’m about to tackle this job this weekend. This will help me a lot and thanks for doing a good job on explaining everything!
@BudgetPlants
@BudgetPlants 2 года назад
Awesome!!.. glad to be of help. Good luck on the project!
@johnlysic6727
@johnlysic6727 Год назад
Excellent video - very helpful - thank you
@BudgetPlants
@BudgetPlants Год назад
Thanks John!! 🙏🏼🙏🏼😎
@travisjordan5392
@travisjordan5392 Год назад
Incredible. I was quoted $9600 for the exact same job for 60' from meter to house.
@lv7603
@lv7603 Год назад
Where are you located ?, in some parts of the United States specially where it freezes water lines has to be installed fairly deep. In other states the main requires copper be used which is expensive. But yeah $9,600 makes you wonder what’s going on.
@BudgetPlants
@BudgetPlants Год назад
I’m here in CA so we do t have to consider freezing, but yes in many parts of the US that has to be taken into account. For these kinds of projects, it’s about 80-90% labor charges that drives the cost up. So if folks are able to do their own, it’s worth it! So long as it’s done properly 😎
@universoullove3384
@universoullove3384 Год назад
Man, this is one awesomely informative video!
@BudgetPlants
@BudgetPlants Год назад
Many thanks!! 🙏🏼
@scottmusial5500
@scottmusial5500 2 года назад
the blue glue you're using is the wet/dry which is good if the area isnt 100% clean. if its visible though, they make a clear primer and a grey glue to keep it looking clean
@deannamenard1631
@deannamenard1631 2 года назад
Great video, it was suuuper helpful, and lots of good tips! We're trying to do some repairs that seemed quite simple but we knew nothing about plumbing. So we got a guy out here to give us a quote and were told it would be $1,300, and more if they needed to break concrete to get underneath... Nope! After a lot of youtube videos I'm feeling more confident about fixing stuff ourselves and saving $1,000+ thanks!
@BudgetPlants
@BudgetPlants 2 года назад
Fantastic! Yes… You can totally do this. Breaking it down step-by-step, it’s actually fairly simple… Just requires a little elbow grease LOL. Best of luck to you on your project… I’m sure you will annihilate it 💪
@aaronbaraiya3692
@aaronbaraiya3692 2 года назад
U done with the repair
@213segura8
@213segura8 2 года назад
Great video man .
@BudgetPlants
@BudgetPlants 2 года назад
Ahh thanks!!!! Much appreciated 🙏🏼 -Dom
@LawrencePlumbingBob
@LawrencePlumbingBob Месяц назад
Amazing how code is so different in the country. I’m in Pittsburgh, PA. We bury our lines 42” deep. There would have been 6” of sand above and below the pipe, which would have been soft k copper or PE. Generally the water service comes in through the basement wall or slab.
@BudgetPlants
@BudgetPlants Месяц назад
Yeah definitely. I think it mostly has to do with weather/temps. Freeze levels vary regionally which would have an affect on line depth. Thanks for watchin 😎
@ra15899550
@ra15899550 Год назад
Great video! Thanks
@BudgetPlants
@BudgetPlants Год назад
Thanks for watchin!! 🙏🏼🙏🏼😎
@user-io1zn1uh5y
@user-io1zn1uh5y 7 месяцев назад
you have answered me properly,i hope for the better with the information picked. thanks
@southerncut
@southerncut Год назад
Awesome video! Would you have done the 1” upgrade if you went with copper? I have a similar job but a 50’ run from main to house.
@jc-yw5km
@jc-yw5km Год назад
Really good job .
@BudgetPlants
@BudgetPlants Год назад
Thanks so much!!!!! 🙏🏼🙏🏼🙏🏼
@seffgill7959
@seffgill7959 2 года назад
Great vid
@ezloop1
@ezloop1 11 месяцев назад
GREAT JOB, EXCELENT VIDEO.
@BudgetPlants
@BudgetPlants 11 месяцев назад
Cheers!! 🍻 👍😎 Thanks for watchin!
@jenniferamedio9184
@jenniferamedio9184 4 месяца назад
The water tunneling device is awesome for going under the drive/walkway!
@BudgetPlants
@BudgetPlants 4 месяца назад
Most definitely! And great for water gun fights 😎😎
@HRTsAFyre
@HRTsAFyre Год назад
You are so awesome. Nice job.
@BudgetPlants
@BudgetPlants Год назад
THANK U!!!🙏🏼🙏🏼
@gg-gn3re
@gg-gn3re 2 месяца назад
Also plastic pipes have less friction loss than copper. This is one of the main reasons for using PVC everywhere now. as well as chlorinated water keeps the molecular structure strong.
@spiritualwartv
@spiritualwartv 6 месяцев назад
Great video feel more confident to do my own water line
@BudgetPlants
@BudgetPlants 5 месяцев назад
Fantastic!!
@patriot1303
@patriot1303 2 года назад
You should mention that changing your main to pvc can in many cases cut out the electrical grounding system in your house and you may need to call and electrician afterwards to fix that
@BudgetPlants
@BudgetPlants 2 года назад
That’s a very good point!
@missravenbellewhatthehell
@missravenbellewhatthehell Год назад
Can you explain why that happens?
@danolanater
@danolanater Год назад
Your electrical box grounds to either grounding rods or water pipes so if you switch to pvc pipes electricity won't be able to go to ground if you don't have the rods
@Ashroyer86
@Ashroyer86 Год назад
Pound a freaking rod into the ground. If you can run that water line you can get a ground.
@vegataxkc
@vegataxkc Год назад
​@@Ashroyer86exactly...
@tomk3635
@tomk3635 Год назад
Wow, looks like I’m doing this myself now…
@hvacdr
@hvacdr 2 года назад
im gonna try your method of shooting water through the soil. I already thought about it but i didnt think the pressure was good enough. The desert soil wear i live is very tuff to dig. I already borrowed my friends concrete saw and i was about to rent a jack hammer til i saw this. ya this is worth a shot. Ive already dug over foot under the concrete and a little over a foot to go so i think this might do it. If it does then dang budy u just saved me 4 hours of heck and also some money. Only thing is i was kinda wanting to put insulation over the pipe. Anyway great video great advice. i noticed that all your joints were actually done properly. I was watching each of the joints and you got it. The one thing people need to watch out for is to never connect male a solid meaning metal, brass, copper etc to a pvc female fitting. You did not do that. If you do the female pvc fitting will crack. Im an hvac guy 16+ years not a plumber but i know a bit about plumbing too. This guy seems to know quite a lot of neat super helpful tricks. Believe me i watched carefully and i didnt see any mistakes at all. such a good video. never seen a video with 0 dislikes EVER.
@hvacdr
@hvacdr 2 года назад
oh god. i just used ur trick and i got the pipe through this way. that said it took me like an hour to do it. the dirt i have here is mostly all rocks and super hard to get through. I had to keep jabbing at it and going to the meter and pulling the rocks and dirt out by hand You saved my A$$$$$$$$$$!!!!! I friggin love you right now!!!
@BudgetPlants
@BudgetPlants 2 года назад
Ahhhhhhh awesome!!!! So happy to have passed along some helpful info. I learned that little trick a while back and it really got me through some tricky spots on irrigation projects. Thanks for the wonderful comments. You rok!!!
@hvacdr
@hvacdr 2 года назад
@@BudgetPlants I rock? No. U rock. I was able to repipe my main line cuz of you. THANK YOU SIRE.
@BudgetPlants
@BudgetPlants 2 года назад
🙏🏼🙏🏼🙏🏼💪💪💪
@DaveTheHVACguy
@DaveTheHVACguy Год назад
Thanks!
@BudgetPlants
@BudgetPlants Год назад
Thanks David!!!
@Sergio-ih6lk
@Sergio-ih6lk 10 месяцев назад
Thanks for the tips much appreciated, just saying.
@user-ty2uz4gb7v
@user-ty2uz4gb7v Год назад
How is the super tunnel water blaster going to get through chunks of limestone and concrete over pour and roots from mature trees?
@BudgetPlants
@BudgetPlants Год назад
Unfortunately it won’t. You would need something with a little more power.
@Sand-Mann
@Sand-Mann Год назад
Sorry if I missed it but did you put a check or backflow valve on mainline because you have irrigation and hosebib outlets? Nice video!!
@BudgetPlants
@BudgetPlants Год назад
Thanks! No I did not. That may be a good thing to have in some applications. I decided against it because I am using anti-siphon valves. Still not a bad idea though as another prevention measure.
@angelf9800
@angelf9800 Год назад
I have a small leak some where in my house but can’t find it maybe it’s the pipe going to the main shut off.
@michianaluxuryrealestate
@michianaluxuryrealestate Год назад
This is all post meter. In our area the water main is all pre meter as the meter is inside the house..
@jfigleaf228
@jfigleaf228 2 года назад
I had this repair done professionally and it had cost me around $1800. Not an easy job for sure.
@BudgetPlants
@BudgetPlants 2 года назад
Yes for sure. It does take some elbow grease!! 💪
@mracer8
@mracer8 Год назад
$1800 is dirt cheap nowaday
@luissonoma6255
@luissonoma6255 Год назад
I have an inquiry; I’m trying to run water to two rooms that will service a washer and two sinks. I’m tapping off a 1/2 pvc that feeds a hose in the backyard. I wanted to tap from the main but they claim that tapping off will cause the house to lose pressure, not sure if that’s true or not. Will connecting from it(1/2 pipe in backyard) to a 3/4 pipe make it more pressurized or allow or allow it to have better water flow or is it already restricted since it’s from a 1/2 pipe or should I just keep it all 1/2”? It will only run about 25’ to the rooms. How much pressure do I need to have two sinks and a washer machine in an efficiency?
@prezzle208
@prezzle208 19 часов назад
Man im jealous. Im in the north and this isnt something an individual can do since water mains are 6 feet deep to avoid the frost layer.
@nancyc3565
@nancyc3565 2 года назад
What kind of grass/ground cover is that? Does it need a lot of water or is it a good substitute for grass?
@BudgetPlants
@BudgetPlants 2 года назад
Hey! It’s called Ruschia nana. Amazing PET FRIENDLY No-Mow Lawn Substitute - Ruschia 'Nana' (Dwarf Carpet of Stars) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-omT9k643oBw.html
@Diablh
@Diablh Год назад
Can you come do this at my house? I'm terrified at the thought of having our water line fixed
@gregorygiraldo9015
@gregorygiraldo9015 Год назад
What do you do with old piping under ground when putting a new one
@BudgetPlants
@BudgetPlants Год назад
I like to remove it if it’s possible.
@melindafranxman1538
@melindafranxman1538 2 года назад
What about freezing where you have the pipe above ground?
@BudgetPlants
@BudgetPlants 2 года назад
In my location I didn’t have to worry about that, however an insulating wrap for pipe above ground would be needed in some colder climates.
@emiliog2916
@emiliog2916 Год назад
gracias
@TMM1111
@TMM1111 Год назад
Great video, thank you. After you uncovered your Union with the valve, you showed a scene where the pipes were as clean as can be at the 4:42 mark. Any tips on how to get the pipes that clean to work on? I have dug down and have uncovered the pipes, but they are encrusted in mud. Wire brush maybe? I was thinking maybe even a hose, then shop vac the water back out. Thank you again. Troy Miller, Kansas City, MO
@BudgetPlants
@BudgetPlants Год назад
Hey Troy, I replied to your email, but also wanted to reply here as well. I recommend using a pressure nozzle on a standard hose. If that’s not strong enough, you can go to a pressure washing machine with a fan nozzle. Just keep it on the lower pressure settings. Good luck!
@catbirdfeeder
@catbirdfeeder Год назад
THE white adapter to size up to 1” to attach from the main line is the weakest link….keep an eye on it…
@davidladd5597
@davidladd5597 Год назад
Did you rule out PEX?
@mikkijohnson1277
@mikkijohnson1277 4 месяца назад
I saw on another video that once finished you should leave the trench open overnight to make sure no leaks appear… 🤷‍♀️🤷‍♀️🤷‍♀️ extra step? Or worth it?
@BudgetPlants
@BudgetPlants 4 месяца назад
Yes! That’s a good step to ensure no leaks 😎
@u812green7
@u812green7 14 дней назад
But you used a schedule 40 adapter for your valve, so that's a weak link in your schedule 80 idea 😉
@gg-gn3re
@gg-gn3re 2 месяца назад
Why didn't you use pex?
@TheBmarquez
@TheBmarquez 2 года назад
where did you buy the pvc and parts at?
@BudgetPlants
@BudgetPlants 2 года назад
The VERY best place to get all sorts of irrigation and landscape supplies is Ewing Irrigation. They have everything you would need to complete a project like this. The staff are incredibly knowledgeable and helpful. They cater to both contractors and homeowners. Definitely a major step up from the big box stores… And have much more professional commercial grade materials. I recommend going to their website to see if they have a store close to your location. Thanks for watching!
@Michael-jm5ix
@Michael-jm5ix 5 месяцев назад
Does code now require it be 1 1/2 or is 1 inch still ok ?
@BudgetPlants
@BudgetPlants 4 месяца назад
It’s really just about what kind of volume you need. For a 3 bed 2 bath house is do at least 1”. Larger properties I’d definitely upsize.
@brycefloto5539
@brycefloto5539 Год назад
Where did you buy all these supplies?
@missravenbellewhatthehell
@missravenbellewhatthehell Год назад
Company called Ewing irrigation all over the county maybe one near you
@marklasvegas6816
@marklasvegas6816 Год назад
Great video! How do I get past my pine tree roots?!!? 😳
@BudgetPlants
@BudgetPlants Год назад
Thanks! I would say to add a few inches of rich loamy topsoil and till it in as best as you can. It may not perform quite as well in the heavily rooted area however.
@synsiatunuu5769
@synsiatunuu5769 Год назад
I'd be careful about using pvc for a water main. Best to use copper! it's the most durable and reliable type to use for underground.
@dixiechampagne2892
@dixiechampagne2892 2 года назад
The frost line is obviously not an issue where you live. Alas, it is in Detroit
@BudgetPlants
@BudgetPlants 2 года назад
Yup. Southern California 😎
@oldowl4290
@oldowl4290 9 месяцев назад
How much of this actually complies with the National Plumbing Codes???
@Tierone1337
@Tierone1337 Год назад
Hydro trench with pressure washer
@uwack23
@uwack23 Год назад
Should’ve used 1” PEX
@mrkraymnd
@mrkraymnd 2 года назад
Why pvc and not pex?
@mrkraymnd
@mrkraymnd 2 года назад
I’d guess it’s because pvc requires less tools and is less intimidating but I was just curious 😀
@ElijahPrivetteRealEstateVlogs
Noob question but why was pvc used and not pex?
@BudgetPlants
@BudgetPlants Год назад
Pex is another good product. I work with pvc all the time so I am more familiar with it and it’s capabilities. Nothing wrong with either product.
@luissonoma6255
@luissonoma6255 Год назад
@@BudgetPlants What about 3/4 CPVC schedule 40?
@BudgetPlants
@BudgetPlants Год назад
The main difference is that CPVC can withstand higher temps. It also has a higher resistance to highly chlorinated water. So it’s fine to use and helpful in some cases, but generally not necessary.
@ZacVaper
@ZacVaper 2 дня назад
Not sure which of his three eyes to look at... 👁👁👁😝
@deeped7249
@deeped7249 9 месяцев назад
Not worried about freezing where you live in assuming
@BudgetPlants
@BudgetPlants 9 месяцев назад
Correct. But Ruschia can take down to 20 deg. f.
@trudyvaccaro1560
@trudyvaccaro1560 2 года назад
I want to see what you planted in your yard instead of grass
@Metqa
@Metqa 2 года назад
Amazing PET FRIENDLY No-Mow Lawn Substitute - Ruschia 'Nana' (Dwarf Carpet of Stars) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-omT9k643oBw.html
@robertdawg4754
@robertdawg4754 Год назад
This dude made a simple job so so so complicated
@kristoffMR
@kristoffMR 5 месяцев назад
Save ton of money and have all that plastic leach into your water even more than its already contaminated with who knows what!
@pandoravex4791
@pandoravex4791 2 года назад
I really hope that duct tape didn’t touch his leg hairs or that would have been painful to remove. Cool video though.
@BudgetPlants
@BudgetPlants 2 года назад
Hahaa yeah I learned a lesson on that one lol
@AlessioSangalli
@AlessioSangalli Год назад
I disagree that sweating is more complicated than PVC cement even for a DIY'er, but why the claim that copper has less friction? I do not think that is true
@gg-gn3re
@gg-gn3re 2 месяца назад
Yea it's pretty easy to do lol Also yea metal has more friction loss than the pvc does, he got it backwards.
@M_santana26
@M_santana26 3 месяца назад
Next time go to your local home depot and rent a trencher. Save ur back for only 150 bucks for the day
@chrisrichardson8908
@chrisrichardson8908 Год назад
Zurn pex is the way to go . Copper is so outdated
@christinariggs7043
@christinariggs7043 3 месяца назад
I don't like the chemicals in plastics
@cupofkratom
@cupofkratom Год назад
sch 40 should never be used for a main line!
@BudgetPlants
@BudgetPlants Год назад
Hence me using sch 80.
@cupofkratom
@cupofkratom Год назад
@@BudgetPlants awesome build
@user-qy9ux4rr3f
@user-qy9ux4rr3f Год назад
Shut this site off
@BOOBIE8707
@BOOBIE8707 Год назад
Showing yourself wayyyy to much… it’s throwing me off . Clicking back and forth
Далее
PEX vs COPPER vs CPVC plumbing pipes
16:56
Просмотров 1,5 млн
MC TAXI: АК-47
35:14
Просмотров 527 тыс.
The Man Who Solved the World’s Hardest Math Problem
11:14
Tapping Into the Main Line
6:31
Просмотров 158 тыс.
Replacing lead water mains
14:29
Просмотров 87 тыс.
The Strongest Fence You Can Build Without Digging
25:39
How to Install Water Sprinklers - Do It Yourself
1:06:11
Просмотров 176 тыс.
УДИВИЛА МЛАДШУЮ СЕСТРУ
0:50
Просмотров 1,8 млн