How to Install Cobra Exhaust Pipes | Honda VTX 1300

Подписаться 220

Просмотров 9 тыс.

50% 1

Detailed installation, WEIGHT comparison, & TEST RIDE, of a full Cobra Speedster Slashdown exhaust system, on a Honda VTX-1300...
We first remove the stock pipes, launch into a DETAILED installation... then take Bessie for a SOUND CHECK & TEST RIDE!
Check out my Oil and Filter change video for this bike:
• How to change the oil ...
...and my final-drive gear oil change for this bike:
• Honda VTX 1300 Shaft D...
Visit VTXOA.com
and VTXCAFE.com
Check out Crash Test Goat's channel:
/ @crashtestgoat
*Wear your GEAR!
#GOATARMY
@vtxfan

Авто/Мото

Опубликовано:

17 ноя 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@Clarke1962gmc 15 дней назад

Question: Is it better to torque the head exhaust bolts first, then tighten frame exhaust bracket bolts second? I noticed you did the bracket bolts first. Just curious what instructions state?

@vtxfan 15 дней назад

This was how they laid it out in the instructions, so far far no problems 👍🏻

@carfreak1234 Месяц назад

Nice Video, Liked and subscribed ✌

@carfreak1234 Месяц назад

except for the screaming stuff you added, that was unnecessary

@vtxfan Месяц назад

😂

@weco1971 3 дня назад

@@vtxfan Castle nuts or for using cotter pins. ACORN nuts bottom out...

@vtxfan 3 дня назад

I have heard that, have been lucky so far they haven’t bottomed out, probably because I replaced the exhaust gaskets, no leaks in 8,000miles, but if they do I will put some washers under the nuts, and would recommend that as well. 👍🏻

@enriquegranado6392 4 месяца назад

Sounds great! I have the same bike and the exhaust sound is a shame... where can I buy that cobra? Nice vid

@vtxfan 4 месяца назад

Hey Enrique, try easternperformance dot com, they may still have one in stock

@PainterD54 Месяц назад

I took my baffles out and wrapped them with muffler insulation. Now they sound alot better and don't have the nasty tinny blatty sound anymore. Yes, I started it up with the baffles out and it was stupid loud. I hate people who run it like that. Just annoyingly loud and obnoxious.

@vtxfan Месяц назад

I’m thinking about doing the same thing. I think it would still sound great while taking the edge off. What’s it like getting those baffles out and back in?

@PainterD54 Месяц назад

@@vtxfan It was fairly easy getting the baffles out. I wrapped them with a little too much and had a bitch of a time trying to shove them back in, but I managed to by twisting them back and forth, then lined the holes for the bolts and got'r done! They do sound better. It's been a couple years now and I may pull them out and see how it's lasting or if it burns out or not.

@aaronshaver5731 2 месяца назад

Have you taken the baffles out yet?

@vtxfan 2 месяца назад

I have not taken the baffles out yet. I might experiment with them soon 👍🏻

@southside1975 Месяц назад

never use those castle nuts with after market pipes they bottom out

@vtxfan Месяц назад

That is true, I have heard that. I seem to be fortunate so far, (the fresh gaskets help) but if they do bottom out when I re-tighten everything up, I will use a washer or two, to make up the difference 👍🏻