My old kerosene furnace conked out and instead of replacing that we've hooked up your wall heaters in every room. Not only is this cheaper than replacing our old furnace, it's a green way to heat our home. This video helped me wire both the 240v and 120v. Cadet wall heaters were very highly recommended by a contractor friend of mine and so far we're saving a lot of money in heating expenses and these heaters can get the house just as warm as the old oil furnace. Thanks!
So both 240 hots went to the thermostats red and black? On my 240volt twin there is a black and red coming from the thermostat. Are both those lines hot?
He did show everything..? Is he supposed to tell you how to install a breaker and run a new wire from the panel? That’s a completely separate side of the project. If you need a video to tell you how to do that it’s best to call an electrician.
If you phase the wires for a 240 volt wall heater (when you reidentified the white panel), then do you have to phase them on the panel? What happens to the white conductor on the panel???
Can insulation be placed right by the can? Or is there code requirements to keep insulation a certain amount of inches/feet away from it for fire safety? I will be using r13 paper backing fiberglass insulation
Great heater. My question is, how do I set the thermostat? There are no indicator numbers on the panel. I can turn the knob to the middle and it will turn on, I assume it will turn off automatically? The heater is installed in a small laundry room that gets very cold in the winter. How do I get it to turn on and off automatically at a comfortable temp to prevent freezing pipe)?
Hi Donnell. To set your thermostat, start by turning the thermostat knob all the way to the right. Once the room reaches your comfort level, turn the knob to the left, just until it clicks and the heater turns off. The heater will automatically keep the room temperature around this setting. From there, if you wish to reduce the room temp, you can turn the knob to the left. If you wish to increase it, turn the knob to the right. Hope this helps!
@@Cadetheat is there any way to adjust the thermostat temperature, like how you would adjust hot water temperature on a water heater? It seems like my top end is such that it just gets going and shuts off. It seems to be working correctly, I just want it to go a little warmer before shutting off.
I installed a wall heater, wired it up correctly and replaced the thermostat because the overheating light continue to indicate it was overheating... I can't figure out what else might be the problem. The last thing I can really think is either the motor is faulty or the wire goes into this metal incased rubber thing that plugs onto the over temp safety control. There is 2, one is clear but the other looks like it might of been blown out because it has a red-brownish color.
I got a question about this heater. I purchased this exact heater that's rated at 1500 watts, If I adjust the thermostat to low or medium will let reduce the watts? For example, could I potentially have 500 or 1000 watts and then if I max it out on high, does that give me 1500O watts or is it a constant 1500 watts no matter what the temperature is on?
Hey there I'm having some issues with mine 120v wall heater. For some odd reason it's only blowing cold air out. Before it was blowing hot air. Is there a reset button I can push or any tricks I can do for it to work again?
I bought the 240 dual cade wall heater. My electrician is telling me I can't use a smart thermostat on this wall heater. I am trying to use a Sensi WiFi thermostat model #ST75 If not what thermostats can be used with the cadet series that is not a cadet model.
The metal turn on piece that the plastic turn on knob is suppose to attach to fell off the heater itself and no matter what we do the metal piece won’t stay on! PLEASE HELP! We’ve tapped it onto the tiny nub with hammer but it still comes off?
Sorry for the late reply on this. Are you talking about a little metal sleeve that comes inside the plastic knob or the actual metal shaft that the knob and sleeve go on (that sticks out of the heater when it is installed)?
My heater won't turn off. I am thinking it might be the thermostat but it checks out ok doing a continuity test. Any ideas what might cause this problem?
HELP😭 please tell me its a way to put this heater on a iron pole with wheels so i can wheel it around the house???? The gas heat is not as hot any more😩
Very good question. That is going to depend on the size of the room you have and if the wall heater is the same wattage as the portable. In general, our wall heaters are most likely going to heat up a room faster than a portable because they have built-in fans that will quickly circulate the warm air around the room. Our heaters are designed to heat entire rooms, where a lot of portables are more designed to heat parts of a room.
Would this heater be a good idea to heat up an attached 2 car insulated garage? I’d like to keep it warm all winter to protect my tools and car and also great for me to go sit in and watch the game.
Hi there! Good question. Although this heater would be able to adequately heat the space, we would suggest looking into our Garage/Workshop heaters that are designed specifically for this setting as they are better able to withstand debris build-up, cold winters, etc. These heaters can be found by following this link: cadetheat.com/products/garage-heaters
your useing the ground as the neutral wire return ? this line should have 4 wires and be a 12 gauge for 20 amp breakers for a 240 volt set up .. 2 hot wires , a neutral and a ground
No. I have one of these for my bathroom and it warms up pretty good, but only a small area around the heater. Anything 4 feel away from the heater is basically room temperature.
I have a 1500 watt in a bathroom. I need a heat source in a smaller bathroom nearby. Can I connect two heaters somehow without having to route a new circuit?
Yes. There is a comment here that indicates you can have two heaters on a 20 Amp circuit. More than two would require a larger circuit and a lower gage wire.
how would installation be different if you want to install 2 240 heaters on a single 20 amp 240 volt circuit? can you wire the 2nd heater directly from the 1st heater?
Hey Chris, Great question. You can install two 240-volt heaters on one 20-amp, 240-volt circuit, but as long as the total wattage of the heaters. is 3,840 or less. If it's more than that, you'll need a 30-amp circuit. The heaters need to be wired in parallel. For details on how to do that, check out our blog post: cadetheat.com/blog/multiple-heaters-just-one-thermostat/ We haven't gotten around to doing a video on this yet. But if you have any questions, don't hesitate to reach out.
Hi Scott. Yes, this unit can be installed in a bathroom as long as it is not above the sink or tub, or in the shower stall area. We recommend installing your heater at least 2 feet (61 cm) away to prevent contact with water.
Yes these can be used as a main heat source. You would have to figure out your square footage for each room to find out how much each heater will heat. An electrician can help with that.
Hey Chris, You should remove the insulation from behind the wall can -- it's OK if fiberglass insulation touches the side of the heater but not foam insulation. You do not need to remove the vapor barrier.
Good question, We suggest you use a surface mount wall can for this type of installation. For the Com-Pak that can be found here: cadetheat.com/CCSMW Please let us know if you have any other questions.
That's right. You'll need the model CCSMW wall can by Cadet. I found one on line. It's a bit pricey though, about $52.00. It has 1/2" K.O.s on all the sides and the back. If you use it though, you don't use the flush mount wall can that originally came with the unit. You simply install the heater unit in the surface mount can after you run your pipe and wires.
William, Sorry for the delayed response. We cover the basic concept of what needs to be done but if you need more help than that, we recommend that you get help from a licensed electrician.
Hi Leslie, Sorry for the confusion. Yes so if you are installing a 120V heater, one of the wires will be a neutral. In that case you need to hook the white heater wire to the neutral supply wire. In this case, we were installing a 240V heater, so we wrapped the wire with black electrical tape to indicate it is hot.
Hi Mathew, that’s a great question. Fan-forced heaters, like the wall heater being installed in this video, are a great option to warm up a room that the central heat isn’t warming up enough or can’t get to. Wall heaters can be used as a primary heat source or as a supplemental heat source like you mentioned. It’s less expensive and easier to install a wall heater rather than modifying the ducting with a central system. Please let us know if you have any other questions!
Marcos, That's hard to say with a definitive answer. What we can say is that wall heaters generally are on less often per hour to maintain the same room temperature as a baseboard heater would be. The fan helps push the warm air around the room, which means the heater needs to run less to keep the room at temperature.
You can get a 2,000-watt version of this heater, which will heat up to 250 square feet in general. Depending on your home, you may need more or less watts to heat that amount of space. For more info, check out this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JoTl5TuS0sU.html If we can help with anything else, let me know?
J Reezy, Which heater are you looking to install? A lot of them can be installed 10" away from the ceiling, but it will depend on the specific model and whether you're using a built-in thermostat or a wall thermostat.
@@Cadetheat thank you for responding. I'm looking at the com-pak 1000 watt for my children's bedrooms. I wanted to put them up high, so that nothing can block them like toys, clothes, etc. I know that the heat will rise, so I wanted to maintain proper clearance from the drywall hard lid ceiling.
J Reezy, We would suggest that you either us a 1000-watt Apex72 that's installed high on the wall or the 1000-watt Com-Pak in the ceiling, either choice would work well for your installation and would keep things out of reach of the little ones.
Hi. Question. My general contractor install a 2 wall heater last few months ago. One of them is for the kitchen and one of them in the living room. But my problem is the heater in the kitchen has no enough heat that coming out from that heater in the kitchen. I'm not sure what is the problem? The wall heater or the wiring connection? Thanks please advise.
Hi our first guess would be that you need a higher wattage heater for your kitchen. Can you share the wattage of the heater and size of your room so we can confirm? (Sorry for the delayed response.)
That should be enough heat for your kitchen area. At this point, we'd suggest that you connect with our tech support team. They will be able to help get you an answer ASAP. They are available for live chat for the next hour and 15 minutes. cadetheat.com/customer-service
Hey there, this particular heater (Com-Pak) comes in 120V, 208V or 240V. Please reach out to our tech support team if you have questions about choosing the correct voltage heater: cadetheat.com/support/customer-service.
Hi there. Yes, you can do this as long as your breaker can support the wattage of the two heaters. We have a blog post that provides some more information on using multiple heaters with one thermostat. Here is the link if you wish to take a look: cadetheat.com/blog/multiple-heaters-just-one-thermostat/
