How To Mount Any Size TV Bracket Into Drywall With Just A Screwdriver! 

No matter how many people say it's fine, I dont think I could ever feel comfortable mounting something big like a large TV onto just drywall. I need there to be at least 1 stud to feel confident about it holding up.

I respect your channel 50 times more for not editing this video. It shows real life problems with real life solutions. Thank you

these toggle anchors are about as much as one could get from attaching to a sheet of drywall. The reality is that the holding weight spec was exceeded by the extra torque due to the bracket acting as a lever. If it were a heavy painting just pulling straight down, yeah one anchor might hold 200+ pounds/100kg. It is just too much to ask from the sheet of drywall though.

My FIL swore by these and much to my opposition, he used them for his 75” TV as he said using studs would weaken their integrity. They held up fine for the longest time…until a hurricane came through and caused damage to his roof which caused a leak, right above the TV. The drywall got wet and down came the TV, causing far more damage than if he would’ve found a stud or two. These are great, if you don’t plan on wetting your drywall. 😂

Having shown how much torque it can bear is a perfect demonstration for us to know how far we can go to be safe. Thanks for the demonstration 🙏 Not every attempt has to go right, we learn by our failures. Thank you again 🙏

I managed a team that did upwards of 30+ TV installations per day in office and medical spaces, and I never allowed a swivel arm mount to be installed in drywall alone. The toggle bolt may hold 50+ lbs, but that doesn't mean the drywall will. We fixed a lot of other people's failed installations. At full extension, the weight of a heavy TV or person leaning on a swivel arm mount is focused on an area about 2in squared and will deflect drywall, and if it has any structural weak points, it will crack it. If you're near a seam, it will crack it. If you MUST use toggles, get a swivel mount that has a wide back plate with 4 fasteners and thus a greater area of contact, or better yet, get a tilt mount that holds the center of gravity closer to the wall. Remember, don't design your solution around the minimum amount of support needed, it needs to be able to handle double a "once-every-5-years load" to be truly safe, or some similar engineering philosophy.

Instructions are straightforward and easy to follow. I can't help but imagine there is some folks out here just stabbing screw drivers into the wall and hoping things line up. I just knew without a doubt there was going to be a segue into a drywall repair video at the end! 🤣 And it was the Vancouver Carpenter guy!

I think the jumping is what did you in on this one

The 265 lbs rating may not apply if you have a big lever arm hanging the load 1.5 feet out from the wall, lol

Appreciate your dedication by messing your wall up to give your audience the skills needed. I used those a few years ago, worked great, just remember that you need a minimum distance behind the wall, sometimes insulation will interfere with the toggle.

Great information. Every time I tune in the info is very useful.

I finally see you being funny! 🤣🤣🤣 Those toggles are awesome and I have been using and recommending them for this application for many years. Be safe out there!

I love those snap toggles! Been using them for years 0 issues!

I just finished installing a heated towel bar using the snap toggles. Thank you for a great recommendation.

I have been using those snap toggle bolts for many years. Best mounting solution I have found.

Yes, I have been using these snap/toggle bolts for several years now to hang heavy objects. So far, no known failures and I keep a steady supply on hand.

I love these snap toggle bolt anchors. They have served me very well. Id be weary of using them for a tv simply because of how expensive it is but ive had plenty of projects holding for years now where a stud just wasnt available. Guess it could happen for a tv too!

smiled like a child when you linked to Vancouver carpenter

"UGGGHHH...Why do I do this to myself??......I'm never going to finish this house..." I've murmured this exact phrase several times while working on my house....

Excellent demonstration, thank you!

Thank you. Just purchased a TV and mount and you popped up in my algorithm. I am going to mount mine in the gyprock (plaster) as new large TV’s these days are so light. The Togglers are sold out in the hardware stores here in Australia & postage is exy from Amazon US so I’m doing it the old fashioned way yet yeah, people up in arms here must have older TV’s that are heavier I reckon. Take care, Mate. 👍

Used the "easy anchor" toggles on my tv bracket. They work great as well.

Breaking the wall at the end was great! Shows that the drywall broke before the fastener. Really good object lesson

Very interesting product. I'll have to check it out

Outstanding! Perfect advertisement for your other very helpful video!!

Thank you for the REAL WORLD scenario! I'm going to give these toggle bolts a try (but not for my TV...)! 😁

Love your videos! How do you mount heavy objects on horsehair/plaster walls? I assume these will not work...

hands down my favorite joke from you ever!!!! combining two of my favorite childhood shows - mr. bean and macgyver. i'm dead.

Now that you've damaged the drywall you might as well throw some blocking back there while you fix it. I wouldn't trust them for a TV or cabinets but I'm going to give those toggles a try sometime. Looks much easier than the old school ones.

Sneaky way to get folk to watch your drywall repair vid. 😂 Thanks for the share.

I love these but very often the screw is way too big for the hole on the thing I'm trying to attach. I wanted to use them on small shelves and such that would hold books but it's almost always too big of a screw.

i actually saw a negative review for the hilti version of these toggles. someone tried hanging a large tv mount and it failed. they blamed the toggle bolts. but when you looked at the picture they provided with the review, it was about 5 or 6 toggles and a huge chunk of drywall around it. clearly the bolts weren't the problem, lol

I can attest that I made a mess hanging a tv about 9 years ago. Never heard of snap toggle bolts back then. But for what it's worth, the tv is still mounted. I'm just afraid to move it. lol

👍👍👍.Thank you

With the adjustable arm brackets, I've never run into a situation where mounting it to a stud would put the bracket in a location where it wasn't adjustable to where you wanted the TV. Do what you want but I would attach it to a stud.

I install and service dental equipment for a living. The largest manufacturer of dental equipment sends these along with their cabinets to mount them to the wall. They are pretty much my go to when studs aren’t an option. Although I always try to get a couple screws into a stud just to be safe.

Interesting... what's the life expectancy of these drywall clips in a coastal environment where corrosion from salt air/humidity is high?

I really do like to see the occasional fail - I never trust just toggle bolts or fancy pants variants - just affix a glued and screwed panel, then toggle bolt into that I say

If you want to mount something heavy on plasterboard only, GeeFix are the strongest fixing I know of...The main down side is you need a slightly deeper cavity behind to deploy them. After those, I would then say Bullfix Extra Heavy Duty, (not the cheaper Universal version). Thirdly, would be the toggle bolts shown in the video. In truth, I would be reluctant to mount any large TV on an arm into plasterboard only, simply because of the extra leverage those arms excerpt onto the plasterboard itself...

I used the same mount on my EU-concrete wall... even for that i have to use very long and thicc screws... but now... i think even a 100KG human can stand on it^^

How the actual?? Glad we still have genius minds in the world:)

I was certain you were going to break the drywall...yet thought maybe "he knows something I don't"! The obvious disconnect is "265 lbs" meaning direct downward shear. That lever arm was never going to stand up to your weight! Yes, I LOVE those snap toggles...just tried them recently!

Hot tip: try a wood screw first, in case there's a stud behind one of your holes, otherwise the anchor tears the crap out of the Sheetrock when it hits wood.

Next video; how to change a cracked panel on an LED television.

Someone offered me a big tv yhat was older but led. The thing weighed over 95 pounds. I bought a 65 inch that weighed about 30. Was afraid to hang the heavy one. Nice system. I think if you gently pulled yourself up it would hold you.

I could see this coming lol😅😅😅

People do this with radiators too and its a recipe for disaster. It will stay up long enough for the contractor to clear off and not answer their phone.

Studs all the way of cousre your not going to use a screwdriver for a stud, but those toggles would be the best choice for a tv

Only thing is, the packaging specifically says not to use to mount tv on drywall.

I still wouldnt trust my 75" on just drywall. Idc if it says 265 lbs and i think my 75 is like 100 or 120. If anything the larger the tv the easier it is to hide the mounting bracket behind it. 2 tvs in my house that are large i extended them with perforated angle to make the legs for mounting long and spanned 3 studs. I needed to do this though because of where the studs were and the factory bracket on jus 2 studs put the tv offset and not where i wanted it or could even have it. Didnt even to drill holes in the tv mount bracket since the holes are long horizontal slots.

Vancouver Carpenter collab? ;D

Okay, then how do you remove the toggle bolts in future?

Too funny!

i would say this is not ideal, but sufficient, if no ones gonna really manhandle the tv. I would not do this with kids!

So you are telling me somebody really put foam and tape to help hold the mount on the wall? If so, they should never pick up another tool or try to fix anything.

I’ve used these and think they are great, but no way would I trust them to hang an expensive, large TV. It may hold, but I’d never sleep again.

So the title really should be "How to NOT Mount Any Size TV Bracket Into Drywall With Just A Screwdriver".

If anyone doesn't know how to find studs behind drywall & how to use a driller & drillbit then stay away from mounting anything, call a handy man to do that. TVs are expensive don't take a chance with inserting brackets into 1/4 inch or 1/2 inch drywall

Well now the walls damaged and needs cutting out and repairing u can throw them anchors away and put some ply in the cavity and close the wall back up the way it should b done properly to avoid the nagging dought in ur head that is that tv ever gonna stay on the wall that’s the way we do it

Considering a good TV can be over $1000, it seems silly to me to not mount to a stud. The weak point with the best drywall anchors is the drywall itself. Finding a stud isn't difficult, even without a stud finder, and a cheap drill is less than $50. 🤷‍♂️

Thats 265lbs static not dynamic. On a stand that is intended to allow the tv to be re-positioned on a regular basis I would suggest these are not a suitable fixing for this application.

Oh no!!! Such disappointment (I appreciate that you tried!). Now you have to make a drywall repair video...

😎⚒️😎⚒️😎

Rated for 265 pounds, drywall breaks. Dude, ease up on the cheese burgers :)

😂😂😂

I hate those as all toggle and anchors like that puncture the rear drywall paper making the drywall weak and rip a large hole just like he did even with a lot less weight. The 265Lbs is complete BS by the manufacture.

Well your obviously well over 350lbs

Scratch that anchor off the list!

So basically everything you just did and said is wrong

This is terrible and dangerous advice! You absolutely should NEVER mount an extendable TV with just Snaptoggles. Snaptoggles are a great product, I buy them in bulk and use them frequently, but drywall alone is not strong enough for that type of mount. For a lightweight, flush mount TV it's fine, but for an extendable / motion mount, you absolutely need to use studs. And you are totally misunderstanding the load ratings of Snaptoggles. Those are the 'ultimate load' aka the FAILURE load. That is the load at which it rips out of the wall. If you read the manufacturer's instructions /specs you would know this. The actual maximum safe working load is one fourth of the ultimate load. In 1/2" drywall in good condition, the max working load is 60 lbs tension, or 62 lbs shear. Please stop giving out dangerous and incorrect advice. You should delete or post a correction on this video (edit: see my update below). And start reading the damn instructions for products before you produce a video instruction people to use it incorrectly, and giving wildly incorrect information about how much weight it can safely support. PS- Where on earth did you find such a tiny TV mount, is that thing made for a dollhouse or something? PPS- I didn't watch the whole video before, but the more I watch, the worse it is- You didn't even use a level and a freakin pencil? How are you a carpenter? PPPS- The more I watch, the worse it gets. You installed the Snaptoggle sideways. For this and most applications, the toggle should be installed vertically, that provides the most strength for this type of load. Which again is something you would know if you read the instructions, or were familiar with any type of toggle bolt.. PPPPS - I finally watched to the end.. 😂Well I'm glad at least people learned something, and I suppose kudos for leaving that embarrassing part in. I still think you should post a correction explaining why that didn't work, and explaining the actual load ratings. And the fact that cantilever loads greatly increase the load on walls, exponentially in some cases.

That was funny