No video :(

How To REBUILD Briggs and Stratton Intek NIKKI Carb that LEAKS WONT START or RUN FIX Common Problem

Jeff's Lawnmower Repair and Service Tips

Подписаться 12 тыс.

Просмотров 49 тыс.

50% 1

How to rebuild NIKKI CARBURETOR Briggs and Stratton Intek 1350 series side shaft engine . Won't START or RUN. Sat OUTSIDE in the Pacific Northwest rain for 2+ years in a pasture. Diagnose Repair and Fix a LEAKING NIKKI style carburetor. Mounted on a VINTAGE Troy bilt HORSE ROTOTILLER cultivator.. Common issue problem, Needs choke to run float floods replace install needle oring gasket wont run wont hard starting SAME procedure for MANY MAKES and MODELS. All horsepower engines Briggs and Stratton Kohler John Deere Poulan Toro Troy-bilt troybilt troybuilt troy built fix repair remove check inspect tips advice troubleshoot take off put on why motor spec tell specification much model leaks gas drive when where what shows petrol fijar reparar how to direction route whats wrong diagnose numbers best easiest way which install installation service horse free advise wont work tell rototiller gas tank wont work broken watch easy way which lawnmower problems replace does can rparts diagram procedure will it oil runs slow goes dies stopped working compression parts diagram 917. sears broke MTD adjust adjustment Yard Machines stratten straton straten john Jon Deere Deer Scott's Scotts Cub Cadet Ariens rider tool tools Jonsered ohv intek single twin Gravely Snapper Hayter Lawnboy Mountfield lowes home depot walmart seafoam grip tools will it run work turn over turbo cool lawn mower repair small service spark compression turnover dont turn over storage
Copyright 2022 Jeff's Lawnmower Repair and Service Tips in conjunction with Jeff's Little Engine Service
Music by BonzaiRod
Donations are greatly appreciated!
Donations can be made by clicking on the link below
www.paypal.com...
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest "backyard" methods for repairing or servicing your lawnmower or equipment. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!

Опубликовано:

18 май 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 49

@ronbo2883 Год назад

THANK YOU! My snowblower was leaking gas into the oil. I never knew if I had a spring somewhere on my float until I seen your video and now I know I don't so thanks for that! The small gasket on the intake valve that you showed was only part there on mine. I ordered the same parts you order and will let you know if it took a good look of my problems. Again thanks!

@jeffslawnmowerrepairandservice Год назад

Excellent!

@lchown1813 Год назад

Wow...thx for the vid.....finally figured out how to get the carb off a 1350 series snow blower....didn't realize the long threaded pins that were through the carb and held the air screen actually were able to be unscrewed...although I thought it was odd the way the ends of the screws were shaped......assuming it works haven't tried it just yet...instead I removed only the float bowl, but the convoluted gasket was hard to get in place without the carb being off too..I lined it up on the plastic side for now.....the float bowl and needle valve etc. are in front of me as I type....

@johndunbar2393 2 года назад

The bit for the bolts you use the 6 sided 5/32 socket on, are called inverted torx sockets.

@jbird7782 Год назад

*external torx. Probably an E-6

@Yo-Yo888AA 11 месяцев назад

There are channels on the bottom side of the emulsion tube that will hold that main o ring in place while installing it on the carb. Also you'll have less chance of damaging the oring for the fuel inlet if you put it over the plastic instead of in the hole

@jayrichards3672 2 года назад

The "mitts" still work. Keep up the good work!

@jeffslawnmowerrepairandservice 2 года назад

Thanks, will do!

@alanharrison7593 Год назад

Thanks great Video. I have a Briggs Intec 15.5hp I now can confidently pull apart

@jeffslawnmowerrepairandservice Год назад

Glad it helped

@jeffslawnmowerrepairandservice 2 года назад

These carburetor can be a pain in the you know what...

@donaldjones3580 Год назад

A Constant Speed engine on a rototiller should fun in transport mode. I put a 7hp engine on mine when the 6hp Tecumseh got too hard to start.

@tipsforthe21stcentury 2 года назад

as always, good tips for the 21st century...

@jeffslawnmowerrepairandservice 2 года назад

Thanks for watching!

@papymuzo8122 Год назад

Thank you super video, hello from France

@jeffslawnmowerrepairandservice Год назад

Thanks for watching friend.

@Thomas-ul3uy 3 месяца назад

You must not have used a Airens tiller. My dad had one and could swivel handle so not walking in where it was tilling. It was a beast of a tiller. Never had any trouble with it. It was heavy, had all cast iron engine.

@nicolashogan6580 7 месяцев назад

Thank you very much for this video.

@jeffslawnmowerrepairandservice 7 месяцев назад

Glad it was helpful!

@jesterr7133 Год назад

I don't even bother doing anything with Nikki carbs anymore. They never run right, and the parts are either expensive or not available. I just throw them in the trash. I will switch to Walbro if one is available, or just throw in an aftermarket. I can get an aftermarket cheaper than a gasket for a Nikki, and the aftermarket run better in most cases.

@harrisonsmith8195 9 месяцев назад

Walbro carbs are overpriced and unavailable for older lawn and garden equipment. Also, walbro rebuild kits are missing vital parts such as jets, accel pumps, check valves. Not a fan of walbro. Absolutely agree that knock off unbranded new replacements are preferred

@jesterr7133 Год назад

You have a lot of videos that are helpful though. I have a Troy Bilt Pony tiller that belongs to my mom. She bought it used, and the identification tags are gone. I have it running really well, but I am having drive issues, and I can't find any information on it without knowing the model number. Do you know of any way to find out what it is? I can't even find a picture of this particular model online, and Troy Bilt said that the engine number I gave them doesn't show up in their database, so I am guessing the engine was replaced on this one at some point too. I guessing it was made in the early 2000s by the styling and remaining decals.

@jeffslawnmowerrepairandservice Год назад

A search for Troy-Bilt Pony will give a variety of options / years for that model. I would look at pictures/parts diagrams to try and narrow down the apx. year that yours was manufactured. Knowing the apx. year can help find parts.