How To Remove And Install A Microwave | Over-The-Range 

Fantastic video, thank you for being slow and methodical for those of us that don't do this every day!

Thank you sir... I DID IT!!! No injuries, nothing broke, minimal cussing. This video was hugely helpful! Really appreciate how amateur-accessible your instruction was. Look forward to more of your videos!

Just replaced one, this was a great help. The previous mounting bracket was only held by a couple of drywall screws and not on a stud, so your toggle info was great. A bit tricky lining up the cabinet bolts, not much room for error, used washers to cover nearby holes. Thanks as always!!!

Best video on replacing under the cabinet microwave oven hands down. Your tips were great.

Great job! Only suggestion I'd make is... plug the microwave in first and confirm that it works before installing anything! 😂 I've learned the hard way with large appliances bought both new and used that this quick test is worth getting the extension cord out for. A bad appliance or bad socket is a huge pain in the ass.

Millions thanks I needed this

Clean work. My first install was overwhelming. You make it look so easy. As you said to double check all measurements. Well done 👍

Nice demo with good instructions. I remember when I installed a combo microwave - stove fan at my former house and it was a real adventure. Luckily I did have a helper for the actual lift to install but there were ceramic tiles on the wall so ... carefully drilling the holes, mounting toggle bolts (nothing lined up with studs), finding a single stud that was almost centred and cutting through the mounting bar and the ceramic tile to get a firm and level mount for the bar. Then cutting for the vent in the bottom of the upper cabinet as well as a hole through the exterior wall for the fan and vent installation through a stucco outer wall where the exterior was over 20 feet above ground level was not fun. When it was all finished it looked great (stainless steel hood and convection microwave as well as the matching electric stove below) and was worth the pain and suffering with a minimum of touchup painting on the exterior wall. I've been tempted to do the same thing in this new house but there isn't enough clearance between where it would have to be mounted and the gas stove below. That will have to wait another ten years when my DW will be promoting the idea of a majorly renovated kitchen.

If you have a 3ft bar clamp, it makes removal 10x easier. Clamp the microwave to the cabinet, remove screws, then support microwave and undo clamp.

I'm impressed you man-handled that microwave on and off the bracket by yourself. Whenever I've tried to do it alone I end up bending the metal tabs and invariably have to ask someone to help.

Well done. And, yes, always move the range. I require my apprentices to do so and if the client says 'no', we don't install the OTR Microwave. They're clumsy to install.

Love your videos, keep up the great work.

Thank you for your informative video & all the other DIY projects

I'm very happy to see this video as I will also be replacing my Kenmore, which is about the same as what was removed in this video. The new one is likely to be a Whirlpool too. Edit: my son and I did the install today and it went well. We took our time, verified the position of the studs, and double checked all markings were at the correct distances. Using the template my initial markings for bracket screws were a little high. I guess I didn't cut the box at the exact spot on the dotted line they wanted. Not sure how much leeway there is but I'm glad I verified. I wish manufacturers would decide on a single template. The Kenmore actually had a U-shaped bracket so now there are three big and two little holes in my wall not being used and 3 "small" and 1 big hole in the cabinet. I covered them up with stickers so nothing would fall down there.

Done! Thanks again for a great video that gave me confidence to tackle this project! Had a bit of an issue with the paper template for the cabinet but then I made my own out of cardboard as I saw it was pretty easy for you. On to the next project!

Thanks, you covered all the steps I needed!

THANK YOU! Tomorrows project looks a lot easier!!!

I had to replace a microwave in an older home and both the back wall and cabinet were Swiss cheese. I ended up adding some plywood to both for extra reinforcement and then I filled in the extra holes in the cabinet with wood filler. After that I covered the bottom of the cabinet with a shelf liner to hide the mess.

Just wanted to let you know I used your video to help myself install an over range microwave this week. My situation wasn't EXACTLY like yours but having watched your video I felt more confident in tackling the project which turned out successful in the end! My Christmas wish list this year will have several items from your amazon store page on it!

Excellent video! Thank you so much for your clear and concise instructions.

I've installed a couple dozen of these things, but I still appreciated your video. I have always gotten the paper template with a bunch of confusing lines that are supposed to compensate for the offset of the back wall of the cabinet. Let's just say that fender washers are my friend. As I recall, the instructions want you to put the top bolts through blocking that fills between the cabinet bottom and the microwave top. Of course I never do. Did you blow through that step too?

When I installed mine I removed a hood fan that was hard wired in. So i passed the wire up threw the wall about 8in and installed an outlet in the cabinet. And my microwave ( a Frigidaire ) has a completely different mounting system. Not harder, just different. It has a large bracket the passes threw the unit and screws in the front top behind the top trim. Yours looked like it would have been much quicker to install. Keep the videos coming and I'll keep watching and learning.

Thank you. Excellent presentation.

Very Helpful. THX!

Charming chap. Excellent and good idea to move range out of the way. Subscribed. :)

Great as always. Thank you.

very useful information Scott

Very Informative !!

That was very helpful thanks 👍

On convertible units you may have to flip the exhaust fan to recirculate back in the room.

very helpful going to do this in a couple of months, perfect timing

Thank you very much. I'm not able to move my range since the kitchen is very small. However the video was really great.

Great video! One thing that wasn't covered was the electrical work (if it's a new installation rather than a replacement). Obviously, an outlet must be installed inside the cabinet. One extremely common mistake is re-using the existing cable that used to power the range hood. The problem with this is that it's wired to an existing 15-amp lighting circuit, so it will trip the breaker every time the microwave is used if other loads (including lights) are in use on the circuit at the same time. The microwave draws 13 amps. The only way to assure a successful electrical installation is to run a separate 20-amp circuit (12/2 cable) from the main panel directly to the microwave outlet, with no other loads connected to it.

That was interesting as I have never seen how microwaves were installed. Thanks.

Thanks, and well done.

Maybe keep the range, get strong boxes or a car jack to stay in place while screwing in the bolts.

Great job

I had to do this once because something caught fire in my microwave, luckily I was able to replace it with the exact same model so I didn't need to drill any new holes and I could just re-use the mounting bracket that was already there!

I removed an existing over-the-range microwave. The snag I hit was that a previous homeowner had granite countertops and backsplashes installed after the microwave was put in. The backsplash came all the way up to the bottom edge of the microwave -- stupid! When I removed the cabinet bolts, the microwave would not budge as it was wedged between the cabinet & the backsplash. Ended up using an oscillating saw to cut the clips in the mounting bracket. Only then was I able to pull the unit straight out.

I had to replace a Samsung Convection microwave after 6 years. I had to replace the original bracket and new holes for the screws. I got 3 of the support clips into the bracket, but not one on the right side. That one is pushing the one side out about 3/8". I got it up, and holding.

ty! i am trying to take down a frigidaire. took out the top screws but it dosent come down much. i am thinking that 2 screws behind the top trim go thru to the bracket also.guess i need to try taking them out. thanks again.

Great information. Please show how to install exhaust hood.

Excellent

good video. Since the bottom of the cabinet has a recess, do I need a filler block for each screw so as not to accidentally overtighten the screws and pull the microwave metal up?

the fender washer was a great tip

GOOD ADVICE SCOTT 🤗👍😍😍😍

What if you buy the same brand. Maybe the bracket can be reused?

Thank you. It's good to know how to do that.

THANKS! TO THE POINT!

Thank you!!,

Thanks!

I'd love to see how to vent my existing (or replacement) one outside that's mounted on an exterior wall but currently recirculating.

Do you not need to use wood putty to fill the old microwave's holes to assure the integrity of thr mounting bracket?

You installed a unit the sits lower due to overall height; that might be against code. There are guidance points to ensure you have your unit at the proper distance from your cooktop, some manufacturers say 30 inches above the cooktop; and code says to follow manufacturer listing. Thats a key metric to consider when buying a new unit. And, in some places there may be a prohibition on how high a microwave can be mounted overall. One bit of guidance says no more than 54 inches above the floor. So, it gets limited in a number of ways. Think about anyone who is under 6 feet tall, like kids. Many times people are pulling very hot food and liquids out at head height. One slip and that person is covered in hot stuff and will get burned. Just think about how sticky and thick some soups are and how much heat will transfer to the body when it hits and sticks. Latest guidance is to install the microwave below the counter level to provide a safer experience for your entire household.

What brand of microwave should I looked into for this project ? I noticed my old microwave does not have any holes where you can actually mount it.

Thanks, now I know how to replace one.

I know this is old but I'm curious if you could tell me why my microwave is dipping slightly in the center on the top after installation.

Nice, thank you. I am running into a problem with removing from the mounting bracket. It appears that it may have been mounted so high that there isn't enough room to lift the unit up.

y not doing a Vent Out window ❓❓❓ - 4 this type of microwave...

Could you do a video on how to install a vent to the outside for the microwave?

How to remove the vented microwave. I tried to take out my microwave but the duct work didn't allow me to remove it.

I tried to install mine and the predrilled screw holes in the microwave are too far out to be screwed in the cabinet. What do you do in this instance? Do I seriously need to go buy a new microwave and measure the depth of the screw holes?

Height do you properly mesure the height for the new macro wave ?

whats your opinion on venting vs circulated microwave ranges? i have to either go 45 degrees then angled 90 degrees exausting outside through the wall bc basement apartment also bc gas meter right above other option is recirculating microwave range… what would you recommend in this situation? the stove is gas not sure if that makes a difference if gas or electrical stove as well?

How do you change the fuse?

The instructions for all the ones I’ve installed say something like absolutely requires two persons to install. I actually got someone else to screw the bolts in on the last one I did since for some reason these units feel like they’re getting heavier🤔

what if there are no studs behind the wall as in condos, can i just use toggle bolts?

wow i thought there was more to it than that

I got quartz backsplash installed where the back of my microwave would have hugged the wall. I would like not to try drilling into the quartz and was wondering if the cabinet alone can provide enough support for the microwave. Can someone please offer some advice?

Setting vents is a big part and moving the fan to accommodate upper or back or no vent.

Hey, seems like there is metal behind the drywall. When I found the stud, I was drilling into metal. What is that?

This may be a dumb question. Why can't you use existing hole for the plug? Great video. Love the channel.

If installing the back bracket level, what if the cabinet is not level?

Yea, you have a space to move the stove to. Many homes have limited space to move the stove from.

Yes so the maintenance man here installed the microwave in the process he dropped it the amount that goes into the wall that you put the microwave on to secure it was bent so we had to get a tool to bend it back and that is what holds this microwave that is humongous and weighs a lot in the process you broke my stove stop telling the stove and broke the shattered it it's a glass stove now I called him yesterday because of the separation from the screws that go down to the cupboard there was a 3-in gap and the other one was secure came back screwed it in it was nice and now it's starting to separate again is it important that they don't separate the ones that are mounted through the cupboard and then drilling into the microwave

👏👏👏👍

Thoses filters are not charcoal. They can be washed and reused.

Mine wont tilt...still stuck to the damn wall and no videos tell why????

mine is GE= no bolts= need size

The cook range at the bottom magically disappeared and reappeared. Lol

2:01

Can u come install my microwave cuz it's hard to find a professional like urself😊

I would not put a microwave over my range. I prefer a hood that has an exhaust fan that goes outside and a light. My micro is on my countertop. Much safer for shorter guests I receive. Reaching overhead to pull a hot meal out of the microwave can't be too safe.

😎✌🖖👍👌🤓

Just let the little hair you have left go...you'll look nice

Like your video. 👍👍👍 THANKS.

How do you change the fuse?