How to Replace Passenger Side CV Axle 06-11 Honda Civic

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,4 млн

Просмотров 152 тыс.

50% 1

Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AACV00127
1A Auto shows you how to repair, install, fix, change or replace broken, worn, or vibrating CV axles. This video is applicable to the 2008 Honda Civic.
This process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
🔧 List of tools used:
• Pry Bar 1aau.to/om3/1AXAA00020
• 17mm Socket 1aau.to/oQ2/1AXAA00015
• 19mm Socket 1aau.to/otW/1AXAA00043
• 32mm Socket 1aau.to/o8/1AAST00003
• Dead Blow Hammer 1aau.to/on6/1AXAA00091
• 1/2 Inch Breaker Bar 1aau.to/oeP/1AXAA00078
• Ratchet 1aau.to/oUY/1AXAA00016
• Torque Wrench 1aau.to/oAC/1AXAA00044
• Center Punch 1aau.to/oc2/1AXAA00055
• Hammer 1aau.to/on6/1AXAA00091
Subscribe: / @1aauto
Check out our playlist:
Honda Civic 2005-2011 8th gen: • Honda Civic 2006-2011 ...
For More Info visit us at 1aau.to/h/abp/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

10 дек 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 102

@1AAuto 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@bggraham83 2 года назад

Can you advise if this is an automatic? From what I can tell Manuals have shorter cv axles.

@lyonsdavid 5 лет назад

I have to do this myself soon because my boot is leaking grease, I've watch a few videos on this particular job, and your video is by far the best! Thank you for all the clear camera angles!

@1AAuto 5 лет назад

Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com +David Lyons

@mikea5205 2 года назад

I can't believe how much shops want for this easy ass job. My mechanic that I used to trust (until today) said it's 3 hours worth of labor 🤣🤣

@doublejabhook 5 лет назад

Just an f.y.i for Civic Si owners, to remove the spindle you're going to need a 36 mm socket.

@1AAuto 5 лет назад

Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c +Kristina Cassandra

@jamespuckett1770 3 года назад

Thank you! I bought a 36 hoping itd be right reading online and it was

@thormilton3574 2 года назад

Wish i saw this a week ago. Got the 32mm had to return it for a 36mm now the CV shaft cup on the passenger side trans output half shaft WILL NOT slide out. It's like something is stopping it, such as a clip or pin. It slides 1-2mm then dead stop. It's not rusted in.

@950Charlie 4 года назад

Excellent "How TO", used to help granddaughter save BIG $$. I have not worked on a Civic before but have swapped a CV axle or two. Ran into one issue ... the axle did NOT hammer out so had to use a uni front axle puller. As tight as it was it would have never driven out. One other hint ... most looking up this vid for assistance will likely NOT have access to lift. Save yourself some time and jack the vehicle WAY UP from the git-go you'll need the extra clearance when crawling under to pry loose the axle from the transmission ... DON"T FORGET JACK STANDS ... Thanks again

@1AAuto 4 года назад

+950Charlie Thanks for checking us out and the feedback! 1AAuto.com

@sl5311 6 дней назад

I got it out laying underneath on the ground with minimal clearance by taking a small prybar from the 6:00 position and a mini crow bar (the ones an inch wide and 8 inches long with the 110 degree bend-the kind used to pry loose roofing nails) from the 12:00 position. I used the 110 degree bend side and put the edge in the tiny space and pushing the prybar from below and the mini crow from above it popped right out first time. It was easy to get the mini crow bar and my hand above it the axle too. This eliminates the pinch-point from below at the 6:00 position- created when using the prybar only- that stymied me for hours and hours.

@versansky75 5 лет назад

Great video. I just got a 09 and these videos will be helpful as all vehicles are different

@lucasjensen4309 Год назад

Dang bro I love this channel y’all always get all the steps and have grate camera and audio quality couldn’t ask for a better video

@Kakunoshin_Niitsu Год назад

you made it look so easy but certainly there is some art in what you do, I commend your skills claps claps

@1evl12aboosted2 5 лет назад

Great video guys step by step like every dam fix it yourself video should be made! Thank you guys so much!

@1AAuto 5 лет назад

@Cross-Country-Biker 3 года назад

Thanks - makes it looks easy, and without unnecessary waffle

@toddsmith1617 3 года назад

I know it won't be that easy.

@miguelsalazar3239 Год назад

Looks like those civics are one of the easiest when it comes to axle change.

@5udd614 6 лет назад

this is the video to watch

@MMartinez1191 3 года назад

what about the damper on the axle the one you replaced doesnt have it and the old one did does it make a difference?

@javijaramillo5749 3 года назад

Great video 👍

@creightongoodwin7535 2 года назад

Great job man!!! I proceeded to damage the wheel sensor and possible the axle screw by watching someone else "hack" video to do this job. The three (3) screws under the lower ball joint are a brilliant approach and very professional, but replacing the tire to remove the axle nut is not the best way (extra steps) to stop the rotor assembly from turning; I use a crow bar leveraged between two (2) lug studs to hold it against the ground. Thank you. I am actually pulling the engine and I need to make room to access the back (starter, etc.) of it.....

@davemiller5018 5 лет назад

Why would you go through all of that work and not change the transmission seal while you have the drive shaft out?

@johnfranko7696 Год назад

I asked the Honda service team about that. They said replacing the transmission seal wasn't necessary. They wouldn't have done it either if you had Honda do the work.

@alejandromorazan3420 2 месяца назад

How come the 1A auto shaft doesnt have the dynamic damper thing that the OEM has? Not sure if thats the name but im referring to that thing to the left between the boots

@fiddlerpin 3 года назад

I have a 2015 civic. The pass side shaft seems to have a bearing in the middle. Does the bracket for it have to come out?

@CryptoNard 3 года назад

Good video.

@danielguzman8346 4 года назад

Is it safe to hit it with the hammer? Great video bythe way

@EATSLEEPJD 4 года назад

Haha watched you guys video to replace my control arm and managed to crack the axle seal or boot. I got grease leaking all over. Now I gotta do this lol smh

@archfapper211 23 дня назад

That's exactly what happened to me!

@RedBeast-fp9uy 4 года назад

What do you do if the axle doesn’t pry out I have a pry bar but the darn thing won’t come out it’s jammed in there

@taterlysaladman9377 Год назад

if you change out the seal, don't seat it fully. only til the outside is even with the outside of the transmission. Seat it as far as you can and it will leak.

@carltonvictor9531 3 года назад

Question to 1A or any experienced personnel here. Is the Civic Si 06-11 has the same front axle as the FD2 Civics. Any info would be dearly appreciated

@rairai5516 4 года назад

Do the notches line up in the grooves? How wld u tell

@Tactical.chocolate 2 года назад

Is this the same for the hybrids too?

@markiie12 3 года назад

is this the same as 2015 model civic ex? just wondering

@abhigyandatta2569 Месяц назад

Is it necessary to get a wheel alignment done after replacing the axle?

@MiickyVega 2 года назад

I have to replace the seal also?

@justinmoore8097 2 года назад

Um what about the fact that no fluid came out when he pulled the axle and he didn't instruct you to add transmission fluid after the fact I could be wrong here but I do believe fluid should come out of there if car is level and pretty sure you have to add some fliud

@rayravshanov 3 месяца назад

perfect

@duuurs 3 года назад

Beware I believe the SI is different. It has a half shaft and a carrier bearing where the cv connects. My Si with 168k is a bear to separate

@CoBobo100 3 года назад

Is this the same for a manual transmission I am doing an engine swap and need to get to the back of the engine I have a bearing that is behind the lower motor mount and can't seem to get around it

@lucasjensen4309 Год назад

A bearing ??? Oh god u blew it up that bad 😂

@jonjudice1155 2 года назад

Wouldn't it have been easier to just remove the strut bolts and let it flop down?

@TheRealIsaiahWake Год назад

Is it the same for a 07 Honda fit?

@jtownsuperhero 3 года назад

Great vid but my 06 1.8l coupe is different as it has 2 pieces to it... 1 axle coming straight out of the transmission to a bracket and then a second “half shaft” at a downward angle to the wheel hub assembly. I’m having a hard time getting the 2 apart which is why I was watching this video. Unfortunately it didn’t help but great job none the less. If anyone happens to see this and knows a good way to separate the 2, I would greatly appreciate the help.

@Queso305 3 года назад

I wish someone would answer this question too. I'm having the same problem

@JasonBarre 3 года назад

Grab a piece of wood, brace it on the back of outer axle metal shroud and hammer the wood, it should pop loose.

@michaelmaxwell7871 2 года назад

does the vehicle need an alignment at this point?

@atifhariz 5 лет назад

Do you happen to know what the torque specs for the outer tie rod is?

@bggraham83 2 года назад

ahahahahh torque specs

@Edwin-om2bu 5 лет назад

Do we gotta drain the transmissuon before pulling the passenger axle?

@1AAuto 5 лет назад

+Edwin Viera No

@alexluquez18 Год назад

I did this and now my axles are binding up, axles are seated properly, does anyone have any insights?

@justinguarino201 Год назад

1 1/4 socket will work on the axel but as well

@robfassi3297 4 года назад

Are they the same part for coupe or sedan?

@1AAuto 4 года назад

+Rob Fassi Thanks for checking us out! This item is specific to engine size, not the body style. This particular unit is specific to models with a 1.8L engine. Hope this helps you out!

@thedarkmage7373 Год назад

You need to clarify that this is only for automatics not manual

@1AAuto Год назад

+The Dark Mage Thanks for the feedback!

@thinshadow551 3 года назад

How much of a job would you have on hand if you broke the seal from the transmission?

@toddsmith1617 3 года назад

Wonder that myself. It's what is keeping me from doing this.

@timmothyames3296 2 года назад

I damage the seal. No clue how bad it's going to be

@TheRealoldcar 2 года назад

Very straight forward and simple to remove the old seal with a long flat screw driver. Install with a round socket that will match the diameter of the seal and tap it in to the bore straight. On non si automatics, left and right seals are different size. The seals should be replaced if car is over 10years. Lubricant with trans fluid during seal install and shaft installation

@glennmoyers4956 Год назад

how come you didn't replace the CV axle seal at the trans?

@thomasbradley5419 10 месяцев назад

What's up with the middle thing on the shaft?

@christopherjohn944 Месяц назад

How tf do u get the lower control arm back on so easy

@colten856 4 года назад

Is the process the same with the 1.3 hybrid model? I’m having a hard time removing the old axel

@1AAuto 4 года назад

+Colten Carbasho Thank you for watching! This is not the same for the 1.3L hybrid model. We do not currently have a video for this, but will add it to our list!

@breakfastenjoyer 3 года назад

1A Auto: Repair Tips & Secrets Only Mechanics Know good to know. I was about to work on it. Looking forward to this video.

@1AAuto 3 года назад

+Mace Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@seansouthard3272 3 года назад

@@1AAuto I have a 2008 hybrid and I’m also having a very difficult time removing the old cv shaft from the main axle/driveshaft. It doesn’t pop out with a pry bar as it doesn’t connect directly to the transmission, being a CVT. Any insight on how to remove it?

@paang8385 6 лет назад

Do we need to do alignment after change this CV joint?

@1AAuto 6 лет назад

Thanks for checking us out. No you do not need to get an alignment after replacing the CV axle! If you or any of our viewers need the part shown in this video please follow this link to our website: www.1aauto.com/2006-11-honda-civic-cv-axle-shaft-passenger-side/i/1aacv00127?RU-vid&GTm5zr72YVI

@MarraDan23 6 лет назад

1A Auto Parts Hey can you guys do a video on installing the engine splash shield for a 2001-2005 Honda civic please

@manuelramos4608 Год назад

So you’re telling me I just can’t remove the two struts bolts & maneuver the knuckle around like that instead of removing the control arm from the ball joint? Cause it’s a lot easier to install the two struts bolts than keep prying out that control arm.

@megatron2535 3 года назад

3:11 🤣🤣🤣 "deez 🌰🌰"

@danieldanydaniel7112 5 лет назад

How much is it for this job?

@1AAuto 5 лет назад

+Daniel Danydaniel A shop may charge anywhere from $400-$1200

@eddwinnas Год назад

I have an 09 Civic SI couldnt do it myself :(

@b4322558 3 года назад

why is there tape on the watchet ?

@shade9026 Год назад

Hope the crush washer was changed too cause that thing was dripping oil from the drain bolt lol

@Raeeban 5 лет назад

What if it is stuck in the transmission

@versansky75 5 лет назад

Try using a longer prybar being careful not to damage the transmission. The longer the prybar, the better the leverage

@anilbaksh9962 5 лет назад

You got to go under the car and pry it out. I changed the drivers side today and took apart the passenger side but it got dark so tomorrow I will pry it out and install the new one.

@taterlysaladman9377 Год назад

that is the tough part. not designed to be easy, they should have put a divit in the casing for a tool to get under the transaxle easier. Best tool is a wide chisel blade with a 14 inch or so handle for prying. Don't damage the seal.

@elchapulincolorado4173 3 года назад

This applies 2013 ?

@1AAuto 3 года назад

+Epifanio Cruz The part in this video fits your application, and the install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

@Mission7608x2 4 года назад

I need to change my passenger side axle...how would I know if the axle is seated right in the transmission when placing the new one in?

@jamespuckett1770 3 года назад

If the splines are different sizes it would only go in one way but if they are equal then it doesnt matter meaning if you can connect it without forcing it then its in correctly

@danielwhite1727 Год назад

Mines stuck to the transmission that’s not easy

@commandokittykitty726 5 лет назад

Can you give me the torque values ? I cnt hear it

@1AAuto 5 лет назад

+Commando Kitty Kitty The wheel hub will be 134ft lbs and the nuts on the lower control arm are 43ft lbs.

@AbyssalTenacity Год назад

Si spindle nut 181 ftlb

@georgemichon426 5 лет назад

How do I use the prying bar?, when the car is just on Jacks.

@versansky75 5 лет назад

Put it in between the transmission and the C/V axel and gently pry towards the opposite side of the car. It should pop right out

@anilbaksh9962 5 лет назад

I took a jack and lifted up the spring and then poped it out. To reinstall I did the same thing as i was fighting with a pry bar for 2 hours to put it back. I then tried a jack and it raised perfectly in place.

@oldrestless 3 года назад

@@anilbaksh9962 what spring?

@KINGALEX90BABY 5 лет назад

Is it the save for a 2014

@1AAuto 5 лет назад

+Tab Loco In the 6 year difference they most likely won't be exactly the same, however the general idea for replacement should be relatively the same. It would definitely be beneficial to additionally consult a repair manual (like haynes) for the correct year of your vehicle.

@KINGALEX90BABY 5 лет назад

Thanks