How to Swap Motor Mounts Complete Guide - Ford Focus Mk1 LR

Подписаться 8 тыс.

Просмотров 27 тыс.

50% 1

Engine mounts are a vital part of your engine. I’ll show you how to swap every engine mount on this Ford Focus Mk1. Every step is shown so that you too can make this a diy garage project.
The mounts I used are better than factory replacements, made by Vibra Technics, and bought from Burton Automotive in the UK - specialists in Ford performance parts.
Here are the links to the mounts in case you need them:
Engine Mount: www.burtonpower.com/vibra-tec...
Transmission Mount: www.burtonpower.com/vibra-tec...
Torque Link: www.burtonpower.com/torque-li...
Thanks for watching and your support.
-- Please Subscribe If You’d Like To See More Videos --
Other Useful Ford Focus DIY Videos:
How to Remove Your Air Box Assembly: • How to Remove the Fact...
How to Replace a Car Battery: • How to Replace a Car B...
Throttle Body Cleaning - How To Guide: • How to Clean Your Thro...
Clutch Master Cylinder Replacement: • Clutch Master Cylinder...
Oil Change Made Easy - Every Step Shown: • Oil Change Made Easy -...
Fuel Filter Replacement - How To Guide: • Fuel Filter Replacemen...
How To Change Spark Plugs and HT Leads: • How To Change Spark Pl...
Valve Cover Gasket Replacement: • EASY: Valve Cover Gask...
Changing Brake Pads Brake Discs and Painting Callipers: • STEP BY STEP: Brake Pa...
Cabin Filter Replacement - Pollen Filter Change: • Cabin Filter Replaceme...
Car Door Lock Fix - Actuator Replacement: • Car Door Lock Fix - Ac...
Car Key Battery Replacement: • Car Key Battery Replac...
Rear Axle Spacers Install Guide: • Rear Axle Spacers Inst...
Other Useful General Car DIY Videos:
Windscreen Chip Repair Guide - The Costs, and REAL Results: • Honest Windscreen Chip...
EASY: How To DeBadge Your Car: • EASY: How To DeBadge Y...
Car Window Tinting Tips For Beginners: • Car Window Tinting Tip...
Snow Foam Test - Worth the Time and Money?: • Snow Foam Test - Worth...
How to Clean Your Car: • How to Clean Your Car ...
Follow the brand on:
RU-vid (Subscribe): / @horus_works
Facebook (Like): / horusworx
Twitter (Follow): / horus_works
Instagram (Follow): / horus_works
Disclaimer:
This video is made to entertain and guide you in your car journey. I hope you’ve learnt something new like I have by watching this video. Please note however that you are solely responsible for trying the techniques displayed. Please follow proper safety practices and understand that this channel is not responsible for any damage caused to you or your property when following along with the channel’s content.

Авто/Мото

Опубликовано:

11 сен 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 145

@BlackWolf-di9gq 3 года назад

This is a great channel. Thanks for taking the time out in making these educational videos. Appreciate it!

@Horus_Works 3 года назад

You're welcome mate - glad you're finding it all useful ✌️😎

@FoCuSonWaR 2 года назад

Hi, just replaced my mounts today, thanks to your guide. It was very easy that way 😉. All the buzzing noises are gone, it gave heavy noise when turning right. The lower mount i couldn't remove the bracket. 1 bold was very tight but ik could remove the mount easy. Thanks again for your very informative video! Regards from Belgium

@Horus_Works 2 года назад

Glad it helped and nice work! Hope the weather is still nice in Belgium!

@lezzpaul Год назад

I got a 2002 ZX3 a couple years ago, and she's turned me into a car person, haha. I'm excited to try working on her myself. Seeing how clean yours is under the hood makes me want to tackle that first, mine is grody and gummed over.

@Horus_Works Год назад

Glad to see that we have another car person on our hands - these are great little cars to drive 👍 Buy yourself some parts cleaner spray from an auto parts store, cover up your fuse box and battery with plastic bags, spray on and hose off with water. Let it all dry, and then hit the plastics with some armor all or tire shine. Wipe it all off with a rag. You will be amazed :)

@lyndellfazekas1839 3 года назад

Good to have you back! So simple and a great result.

@Horus_Works 3 года назад

Many thanks!

@subx3dth 3 года назад

wow that is one clean engine bay!

@Horus_Works 3 года назад

Thanks! I try to look after it.

@10weslleynereu 8 месяцев назад

This one must have been hard to record. Thank you so much!

@Horus_Works 8 месяцев назад

It was! But thank you, for watching and commenting :)

@zurcherzurich213 3 года назад

Greetings from Switzerland! I bought my 2004, 1.8 petrol Zetec, Turnier three months ago :)

@Horus_Works 3 года назад

Greetings mate! Congrats on the buy - hope you enjoy the car! 😎✌️

@zurcherzurich213 3 года назад

@@Horus_Works Yes, I really do :) Go on with your good work

@Horus_Works 3 года назад

@Zürcher Zürich Thanks mate, I will 😁

@Abauto84 Год назад

very good style of presentation

@Horus_Works Год назад

Thanks Alex, I hope you found the video useful 👍

@gustavoreyes5490 3 месяца назад

Excellent video ! , 👍 I'm going to follow your guidelines step by step. Thank you so much from Latin America!

@Horus_Works 3 месяца назад

Thanks for watching and your comment - I hope the video helps you change the motor mounts on your Mk1 Focus 😃

@kevinransome7973 Год назад

Thanks for your videos on the focus. I own a 2004 and today I followed your video and replaced all three mounts, perfect. Vibrations gone. Enjoy all your content.

@Horus_Works Год назад

Glad the vids are helpful mate. Changing engine mounts on a Mk1 are not too bad.

@philtucker1224 3 года назад

Thank H, another great video, very clear and instructive. Mine is a MK2 but I’m guessing it’s basically the same process. Live long and prosper buddy 🖖 🇬🇧

@Horus_Works 3 года назад

Thanks Phil, really appreciate the positive comment mate 👍

@DRIV2HORIZON 3 года назад

Amazing video pal !!! You helps a lot 🙌

@Horus_Works 3 года назад

Glad you think so!

@zigman1976 2 года назад

Expertly done!

@Horus_Works 2 года назад

Thank you :)

@zigman1976 2 года назад

The thanks is all mine. I just bought a 2005 zx5 at the beginning of June and I’m going over RU-vid vids so I can start replacing and upgrading my ride. Motor mounts are definitely on my to do list. I already like driving my focus and can’t wait to make the driving experience better.

@mrbenn747 3 года назад

Very useful video! Thanks 👍

@Horus_Works 3 года назад

Glad you think so!

@quotagious 2 года назад

This has come in handy Erik i'll be doing mine sooner than later I think Thank you

@Horus_Works 2 года назад

You're most welcome David 👍

@alexandrupop790 Год назад

Verry well explained. Many thanks!

@Horus_Works Год назад

Welcome 🙂👍

@remigiuszb7048 3 года назад

Well done, everything shown step by step, waiting for the next films. I have the Focus myself :). Greetings from Poland!

@Horus_Works 3 года назад

Thank you very much! Hope you like the Focus, I think they are great cars!

@remigiuszb7048 3 года назад

@@Horus_Works yes, but it has been behaving strangely lately, the engine RPM increases by itself at idle above 3000. It can accelerate by itself, you cannot brake the engine. Heard this could be pneumothorax vent. What do you think? 1.8 Zetec engine

@djiricka 3 года назад

Well I think I don´t need to do it yet on my ST170. But you are doing good job man. Good tutorial ,step by step and clear instructions. Keep it going and wish you lot of kilometres (or miles) in your Focus.

@Horus_Works 3 года назад

Thanks!

@VEMANIS 7 месяцев назад

I love that you and me have the same taste in cars. I have an Ford Focus Mk1 and i love the alfa romeo gt. One day i will buy one. Cheers!

@Horus_Works 7 месяцев назад

Haha thanks mate. I enjoy enthusiast cars, for me cars have to make you feel something when you own them :)

@Laci_G 3 года назад

Nice job, good video. I exchange the torque link at the last weekend. 🙂

@Horus_Works 3 года назад

Nagyon köszönöm Laci! Thanks very much!

@BottleJackBuddy 3 года назад

Thanks for the video.

@Horus_Works 3 года назад

You are welcome!

@kustominkaustralia 10 месяцев назад

Thanks for the vid. My wife's focus destroyed it's idler pulley last week so after replacing that (and belt tensioner) these mounts are next on the list.

@Horus_Works 10 месяцев назад

Glad to see that the videos are useful. New mounts will make a nice difference in ride quality 👍

@haizi7179 4 месяца назад

Damn my idler pulley also destroyed itself about 5 months ago lol.

@nikolajugovic5103 3 года назад

Good work , thanks 👏

@Horus_Works 3 года назад

No problem 👍

@nikolajugovic5103 3 года назад

More videos please👏 good work👏👏 respect

@superwausindahous 2 года назад

Thanks dude.. Mine are ordered and was planning on going to do it next week.. I knew it's a easy job! But you made it more easy for me 👍🏼 now I don't need to surche for the NM specs!!! Thank again for that.. Good video!! Greetings from the Netherlands 👋🏼 (🇳🇱the Max Verstappen33🏆country 😂)

@Horus_Works 2 года назад

You are very welcome my friend! I hope the weather is still good for you in the Netherlands!

@graemehunter5403 2 года назад

Now I know What I need to get the mechanic to do. Great,,,

@Horus_Works 2 года назад

I hope it helps mate.

@ArthurDaley1 2 года назад

Thanks for the video, I have now changed the mounts on my 2.0 Ghia Auto. Had some trouble with seized nuts on the transmission mount and had to use a nut remover to get to of them off.

@Horus_Works 2 года назад

Glad the video helped, and I hope the new mounts made a big difference!

@ArthurDaley1 2 года назад

@@Horus_Works massive difference, I could literally stick my finger through the transmission mount, the vibration was so bad it felt like it was running on 3 cylinders.

@Dzhookac 2 года назад

I watched this video a couple times before i swapped my mounts. This is Zetec engine in the video, same mounts go for 1.8 TDCI 100PS (74kW). Great video, it helped me a lot! :D I only had one big problem that took me hours of work: A bolt in the third mount, was stuck in a mount itself, and when i tried to unscrew it, the bolt head just poped off. Like a cut. The M10 thread was not stuck, but the bolt body through the mount. Friend told me this could happen if the bolt is made of steel, and the mount body made of alloy. Not sure why this would happen but it did, so i had to cut the mount with a grinder in several places until i took it off finally, and then unscrew the M10 thread peace that was left. I practically did an 8 hour job just on this one mount. The first and the second mount went just like in the video. It took only an hour to replace both of them. Thank you for a very useful video, hope you make some more videos on this focus.

@Horus_Works 2 года назад

Thanks for sharing mate. And sorry to hear about the stuck bolt - hopefully others will take note in case it happens to them.

@colinmann3480 4 месяца назад

good video, & it pays to do these jobs your self, the money you can save.

@Horus_Works 4 месяца назад

Thanks Colin, most jobs on cars can be done at home and fairly cheaply - I hope these videos show that. Appreciate you commenting. 👍

@RobertJohnson-dm9br 2 года назад

Hey, well done on this. Good quality production, editing and content. I’m loathed to be critical but all Focus’s are inline 4 (or5). A horizontally opposed engine is a boxer engine like Subaru’s. Again well done, I look forward to more in the future.

@Horus_Works 2 года назад

Good pickup Robert - you are correct of course! Thank you for watching, I appreciate it 👍

@Asepdwi 3 года назад

God job bro👍, I'm from Indonesian🙏see you

@Horus_Works 3 года назад

Thanks Asep! Greetings from Australia!

@alirazmjou2149 11 месяцев назад

درود بر شما متشکرم اقا . شما مرد باهوشی هستید .Thank you so much for this video

@Horus_Works 11 месяцев назад

Most welcome 😀

@martinolsson8303 14 дней назад

Awesome video! You got yourself a new subscriber :)

@Horus_Works 13 дней назад

Thanks mate, I appreciate it!! There is a tonne of other DIY vids for the MK1 here 😀 ru-vid.com/group/PLof3-wBOirGEWyRrHvNZ6NVJHgpAEn7y-

@martinolsson8303 13 дней назад

@@Horus_Works yea, I noticed that and I have watched almost everyone allready Lol! Very good and easy to follow instructions on every video I have seen so far, keep doing what you do, I am sure your videos will be even more famous in the future :)

@Horus_Works 9 дней назад

@@martinolsson8303 thanks mate, I appreciate your support 😃👍

@markusschroer6530 5 месяцев назад

Thank your for this video, it really helped. But there is one ting you probably didn't notice: the outer bolt hole in the torque link bracket (the side the bolt head rests on) has a bushing in it with an interference fit. So when you tighten the bolt, this bushing tightens up against the bushing of the torque link. The bushing in the bracket can easily be pushed back using channel locks, so you have clearance to fit the new torque link. So you didn't have the remove material from your torque link's bushing.

@Horus_Works 5 месяцев назад

Interesting... I didn't notice that, you're right. Thanks for sharing!

@mihailkirilov6445 3 года назад

Hi from Bulgeria!

@Horus_Works 3 года назад

Здравейте So glad to see I have people watching from all over the world! I was born in Transylvania - Romania, so we were neighbours a long time ago!

@mihailkirilov6445 3 года назад

Nice!Thx men,see you end good luck.

@Horus_Works 3 года назад

@Mihail Kirilov 👍

@alexandrupop790 Год назад

Mulțumim!

@Horus_Works Год назад

Thank you, my friend, I appreciate your support 😀🙏

@sanelekunene7344 Год назад

My Ford Focus (similar to yours) 2004 model, 1,6 engine vibrate when cold, and makes some noise inside while driving. I even switch on the radio to avoid the noise.

@sanelekunene7344 Год назад

You nail it Sir, can you share with me the lower engen mount number. I had replaced the one under the water tank but there is still sound coming out. Thanks again Sir, you can lecture

@Horus_Works Год назад

Hello my friend, thank you for your kind words. I purchased all of my mounts form this website: www.burtonpower.com/catalogsearch/result/index/?appl_model=Ford+Focus+Mk1&q=engine+mounts+focus

@JJOKER721 2 года назад

Congratulations on your excellent video, greetings from Italy..but a fix for those yellowed headlights ? Bye

@Horus_Works 2 года назад

Soon, promise :)

@brallybear620 3 года назад

Very instructional video, but Jeezus the music!

@Horus_Works 3 года назад

Haha, thanks, not a fan of the music?

@brallybear620 3 года назад

@@Horus_Works I have a sound system connected to my PC and the "popping" sound in the music can still be heard when sound is almost muted but your voice at that sound level can`t be heard at all. I am an old geezer and my music taste apparently is not the same as yours, and that is of course okay. Still I think you will have more viewers to your excellent videos with more, or maybe none, discrete music.

@Horus_Works 3 года назад

@B Rallybear thanks for the feedback mate - I'll revisit the audio settings on future videos 👍

@andersonmorisco3380 3 года назад

I'm from Brasil and tour vídeos are so great. Congrats. I have Ford Focus Mark 1 and where do you buy these parts?

@Horus_Works 3 года назад

Thanks very much! I bought the engine mounts in the UK. I have left a link in the description.

@pointzero255 Год назад

thanks buddy, getting ready to tackle the mounts challenge soon :P ~ I really like the red hoses you have installed, any guide on how you did that? (and parts used), and did your mk1 have any boot/trunk leaks? thanks and greetings

@Horus_Works Год назад

Hi mate, happy to see that you liked the video 👍 No leaks in the boot for me. You can check out how I put the red hoses on in this video - there is also a link to them in that video's description: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ktZY29VX390.html

@duncanstewart2884 6 месяцев назад

Hey man, love the videos, my torque link bracket sheared in 2 places and the one bolt also sheared. I am going to buy a new torque link and a new bracket, however I am struggling to find replacement bolts. Any idea where I could find those bolts online? Cheers

@Horus_Works 6 месяцев назад

Hey mate, sorry to see the problems you've had. How did the torque link shear of??!! 😵 I would try and find replacement bolts from another Focus that's being parted out. Check eBay UK or USA for Focus Mk1s being parted, and message the seller with photos showing what you need. Best of luck mate 👍

@ricardopires7760 2 года назад

Hi, tankyou for the nice video. I have a Ford Focus 1.8 TDDI MK1, and the 1st mount you show is not the same as mine, but the mounting process is the same, My question is: the other side is the same method or not ?

@Horus_Works 2 года назад

Hi Ricardo, the other side will be easy for you to check. Just take out the air box in front of the fuse box and you will be able to see the mount. Sorry I can't do this for you because I don't have a 1.8 here to check.

@gonzaloperdomo9111 6 месяцев назад

Sirve para ford focus 2006 motor duratec a2.0 ?

@imalexandros3150 Год назад

I have a 2003 ford focus (europe) 1.6 16v. Every time I press the accelerator sharply, I hear a clicking noise from the front right. Is that sound from the motor mount?

@Horus_Works Год назад

Yes it could be a motor mount. Especially if you have a bit more engine vibration than usual 👍

@safwatrahman9374 2 года назад

Hey dude, great video on the motor mounts. i recently got the oem engine mount that goes on the chassis under the coolant reservoir. The plastic top of the mount popped within 5 minutes of the test drive after installation. the mount still has the hydrailic fluid trapped in the rubber. I was wondering if it was a manufacturing defect so i could get a refund from Repco?

@Horus_Works 2 года назад

Definitely take it back mate. Nothing should be coming off the mount...

@Roadhammer3406e 2 месяца назад

Please tell me where you got those red coolant hoses

@Horus_Works 2 месяца назад

Here you go: www.burtonpower.com/parts-by-fitment-type/parts-by-engine-ford/ford-zetec-e.html?product_area=Cooling+System&product_group=Silicone+Hose+Kits

@user-gu4uh3mf3v Год назад

Thanks for your viedos, I appreciate your work you do. Following your guides is like playing with lego as a child but with this ' small' difference it's a car not lego, however, emotions are similar 😊 after doing my mounts I noticed an engine is not levelled, it goes slightly down to the left (standing front of a car) is it okay?

@Horus_Works Год назад

Hi Adam, thanks for your comment, I appreciate it 👍 Did you replace both the transmission and the engine side mount? If you did both, there should be no problem even if there is a lean. If not, maybe have a look to see if the other mount is failing.

@user-gu4uh3mf3v Год назад

@@Horus_Works I replaced 2 of 3 (the bottom one and the one under an air filter) which weren't touched for 20 years, were corroded and rubber was cracked. I left one to the left, it seems to be ok, no rust, rubber "fresh". What about levelling an engine - it came to me after doing my job (engine shaking on idle, What stopped after it).

@mikemayers9353 3 года назад

you are gonna have more vibration with those mounts:)))

@mikemayers9353 3 года назад

you did wrong by grinding , it goes in with a tap , and the metal cilinder is meant to bind to the support and have the poly bush move

@Horus_Works 3 года назад

I knew that but I wanted these anyway - because performance modifications later on. If you don't want vibrations the normal oem mounts are fitted exactly the same way.

@cosminucv5450 3 года назад

Bro i have a problem with my car, Ford focus mk1 ghia 1.8. How can i send to you a video?

@Horus_Works 3 года назад

Hi Cosmin, see if you can describe it here mate, or jump on the Facebook focus mk1 groups - I could take a look at the video there, as well as many other Mk1 experts!

@quotagious 3 года назад

Tell you what I've been thinking about and I can't find anything on RU-vid about it , I had a 1.3 Mk2 Escort with a oil separator for the crankcase ventilation with a PCV the same as the valve on the 1.8 / 2.0 Zetec engines can the oil separator on the 1.8/2.0 be removed and cleaned out ? I know the valve and pipe on the back of the engine can as I swapped mine out for a more rigid poly pipe which makes it breath better for the crankcase Is this something you can look at ?

@Horus_Works 3 года назад

Thanks for the suggestion David. I'll take a look as I've been meaning to take a look at my PCV valve anyway. Maybe I can make it into a bigger project.

@quotagious 3 года назад

It maybe worth just going that deeper into that area just to even see what crap there is in the separator that's if it's if it's possible ?

@Horus_Works 3 года назад

Hey David, just wanted to give you a heads-up mate, I took a look and the oil separator is buried under the exhaust header once the engine is in the car, so I can't get to it unless I remove the headers and a few other bits. It doesn't look like I'll be able to do this any time soon so hoping you manage to find an answer without me. And if you do let me know! To be honest looking at your engine on a stand, you'd be in a better position to take the oil separator off so if you do end up doing this, let me know how it goes... Cheers for now.

@quotagious 3 года назад

@@Horus_Works Hi No the engine was not mine it was a picture off google just to show the part I was on about , I've just put a new PCV valve on mine I think I need to do the throttle body next which i've watched your video twice now on doing that so that will be the next job I think as she is idling a little low to me , Thank you in anycase :-)

@Horus_Works 3 года назад

@David Quotagious ah I see, sorry my bad, I thought it was your engine. Enjoy the vids mate, more to come, and stay in touch - see you on the FB groups 😎👍

@JUSTDOIT-wv1jb Год назад

Are the engine mounts the same for gasoline and diesel engines? I have a 1.8tddi diesel engine.I would like to get these engine mounts..

@Horus_Works Год назад

I would assume that the engine mounts for a Focus MK1 diesel would be different because it's a different configuration - different engine and gearbox, so probably the mounting points would be different. I'm not 100% sure on that though - I just don't have a diesel here to check, we never got the tddi here.

@ShadowPt1987 Год назад

They are exactly the same and on the same places. I have a tddi

@rhijengabino126 2 года назад

what size those stock rims u have?

@Horus_Works 2 года назад

They are 17" factory rims

@Hobbyzocker100 3 года назад

My Ford Focus 1.8 16V vibrates when the engine is warm

@Horus_Works 3 года назад

If only when warm, it might not be your engine mounts.

@mfamily3173 2 года назад

I have a st170 2003 will everything be the same

@Horus_Works 2 года назад

If not exactly the same then it will be very very close. But if you haven't worked on a car before, you may want to start by doing other small projects on your car first and get familiar with working on cars. This is not a project you should attempt if you don't have the confidence, or if you don't have the tools.

@mfamily3173 2 года назад

@@Horus_Works thank u

@MrChashitsu Год назад

Great video, thank you! Here are OEM numbers of engine and transmission mount for 1.8 / 2.0 gasoline zetec ;) 1112025, 1061125

@Horus_Works Год назад

Awesome, thanks for sharing! 👍

@batuhanertan6753 3 года назад

Stock 2.0 ST models?

@Horus_Works 3 года назад

Same engine mate so should be exactly the same steps.

@nan74nan74 2 года назад

for ST170，driver side ＆lower engine mount are same with 2.0。but passenger side are different，they had different pitch

@colinrich3226 2 года назад

gret video,.. Why the music? its so grating. Do we need music?

@Horus_Works 2 года назад

Thanks Colin, not a fan of the music I see? Not necessary, just trying to keeps the vids interesting. 👍

@mikemayers9353 3 года назад

if you dont change the nuts and bolts the torque rating will be off

@Horus_Works 3 года назад

Thanks for the tip. I'll check them to make sure they are still torqued.

@mikemayers9353 3 года назад

@@Horus_Works im subbed ;) love to see a man passioned about a nice car most think is a old pos ;) i own the st170(svt in usa) and i love it . Happy motoring ;)

@Horus_Works 3 года назад

@Mike Mayers I think they are highly underrated - love these cars. Nothing out-handles them for the money. Welcome aboard - glad to have you 👍