Installing a Warn 3000lb Winch on 2017 Yamaha Grizzly 700 

“My shed my shed my shed” sold it for me im subscribing😂

Looking good. Winch is a must have for sure. I just installed a 3500 LB. on my 700 Arctic Cat Trail. Took me a couple days off and on. Finally got it figured out.

Hi, just installed one on mine 17 grizzly and had similar issues . The mounting bracket was ok but the instructions did not show the same control relay . Took a bit of extra time to install but happy with the results...used dielectric grease on all connectors (was not in the kit). Also put the positive cables in some insulating loom (princess auto) for more protection against rubbing trough and causing a dead short to the frame ...Did remove the front bumper for easier access... Thanks for your video..

Ahh gees, surprised the kit was a bit of a hassle.. usually they are pretty plug and play and don’t need to much modification. Either way glad it worked out in the long run. I’ve run into that I know with a few installs for some things on the brute force here where I had to modify somethings to get things to work out! Thanks for sharing buddy! Take care, cheers!

Nice work, thinking about picking up a winch for my snowmobile, sure makes life easier when you run into a bit of trouble....

It's always more work than you figure when doing upgrades! LOL! Great job! Those tires look like they're itching for some use! ;-)

Nice job had to do a winch install on one my cats the last two when bought made sure they had on when bought to save all that fun you just done lol .

Nice, thanks for video , just got a 2021 Grizzly and want to put a winch ... Warn winches seem a bit pricy, how's it held up? How's their warranty ?

Yamaha sells the Vantage 3000 and Provantage 3500 kits for their side-by-sides. That's why some things are different.

Nice work Bud, Ill be taking my new SxS out tomorrow. So if you see a camo honda 500 that will be me out in Dieppe :P

Good video super winch terra are the best winch on the market

the winch was a 30 min install on my 18 kodiak 700, outside on a sunny -10c dy in the snow. that wire you cut off could have been left and hooked up in a daisy chain, it only draws about 200mv. fortunatly my winch plate bolted right on, no drilling. install was under 10 min, the other 20 min was running wire up for the switch

Have you had any issues with the solenoid being down there? I mounted mine there but am debating if I should try and move it up higher.

You should have investigated more. Grizzlys are prewired for the Warn winch. There is a connector for the wire so you don’t have to use the pigtail. I used my pigtail for my heat demon hand grips and also for a set of LED lights. The connector is under the battery cover. Nice bike. I have the exact yeah and colour bike.

Hey bud, I guess you're the guy fix who fixed our internets and guess you saw some of my decals lying around, haha. Following you back. (I don't have instagram)

This was helpful.. thank you

I am a little confused on how you can make this. The 3000 lbs winch's normal operation current is over 200 Amps. But the battery in Yamaha Grizzly 700 cannot provide such big current. I think the battery is only 12V 16A. Since 16A is far smaller than 200A. It seems the winch will not be able to work for a long time. Could you please tell me how you figure this out? Thank you very much.

Good job ! Thanks.

Hey Bud nice install sounds like the instructions weren't much help? Had to figure things out on your own oh well Your sure dressing that Grizz up quite nice.. Tires , Box , grip warmers , and winch eh! Enjoy your new Grizz!!!

Where did you mount the solenoid Sir?

fit like a glove on my kodiak

Hi. Where is the connector box / block installed?

There is still chalk on the tires...need i say more...lol Is it done snowing yet?

Where did you buy your winch plate?

Nothing like over prepared. I got 3000 on my 04 Honda 350 and a 5000 on my side by side.

Good vid. Disappointing instructions & hardware, especially if it was specific to your bike.

Good job. Too bad you ran into a couple of issues, especially since you got the winch from the dealer and it was intended for use on a Yamaha ATV. As I have not had the best luck with warn winches in the past, I decided to give the Superwinch Terra line a try on the new machine. Really good installation with the proper mounting plate made installation easy. It even included a separate remote connector with and extension remote switch so that the winch can be operated while not on the ATV. Have used it several times now and have not run into any issues thus far. The rope style winch cable is nice, but costs a bit more. As I heard that you really have to do maintenance on the rope if you ride in muddy or boggy conditions, I decide to stick with the old reliable wire rope this time. However, the new winch has a spool that can accept the rope if I decide to change it out. Only will need to change the type of fair lead on the winch (as the roller style does not work with the rope. All the best with everything. Now you got to get out and ride. Hopefully, the snow has melted a bit there in NB. We have lost a good portion of what we had. Warm temps for tomorrow so I am hoping to get out for a run myself.

Gotta hate when there's left over hardware - lol - always puts that little bit of doubt in the back of your mind - hahaha.

I like your intro song send me the link please

How much do those bighorns slow it down?

👍

Hello dost ne Gadi Ki price kya hai

You need a wood stove and fridge tapped out with a keg. LoL 🙄 That's what I had in my shed.

my atv has a 4500 pound wench on it my friend

nice job, next project?

You don't show doing any mechanical work at all. No help whatsoever!

Dude, stop shaking the camera. Whats the mater with you???? Almost puked over here.