Kenmore Gas Dryer Not Heating - How to Fix - DIY

Подписаться 44 тыс.

Просмотров 276 тыс.

50% 1

danthefixitman....
amzn.to/3Z5eMHC - same thermal fuse I used in this video from Amazon.
amzn.to/3plnAx7 - AstroAI Multimeter Tester 2000 Counts Digital Multimeter with DC AC Voltmeter and Ohm Volt Amp Meter ; Measures Voltage, Current, Resistance; Tests Live Wire, Continuity
amzn.to/3PBxSDG - 3392519 Dryer Thermal Fuse (3 Pack) Replacement for Whirlpool WP3392519 Replaces Part # AP6008325 3388651 694511
amzn.to/44lzHZK - MALCO MSHMLC 4-inch Cleanable Reversible 1/4-inch and 5/16-inch Hex Driver (1-Pack)
amzn.to/3prZqAO - DEWALT 20V Max Cordless Drill / Driver Kit, Compact, 1/2-Inch (DCD771C2), Yellow
amzn.to/3pBuQES - Wera - 5105650001 Kraftform Plus 334/6 Screwdriver Set with Rack and Lasertip, 6-Pieces
Just a quick video showing how to fix a Kenmore 80 Series Gas Dryer that runs but will not heat up. This ended up being caused by the thermal fuse that was bad. The clogged vent hose and dirty lint screen vent/housing caused it to overheat and fail.
You will need:
a Multimeter set on Ohms
a 1/4" nut driver and/or drill or other type of wrench to remove the back panel.
A small blade screwdriver or other tool to remove the vent hose.
Thanks for watching!
Please Subscribe!
-Dan the Fix it Man
www.danthefixitman.org
www.amazon.com/shop/danthefixitman
This video is intended for entertainment and informational purposes only. Any repairs you make are your responsibility. I am not liable for any damages to you or your vehicle or your property.
As an Amazon Associate I earn from qualifying purchases.

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 196

@GLACIOUS13 Год назад

We did it! I convinced my girlfriend to get behind the dryer (I COULD have fit but) and she followed the instructions and replaced the old fuse, vacuumed the duct-works and... ...voila! The dryer is drying again! Those of you a little shy about tools, my girlfriend is NOT the greatest with hand tools by any means. She did a fine job none the less! She's the greatest!

@rephaelreyes8552 4 месяца назад

It’s definitely better than buying a Samsung dryer. Samsung appliances seem to be made to last 4 years

@alexhatcher8812 3 года назад

the fact you showed the ignitor glowing BEFORE but no solenoid click is important. so many people just think its the flame sensor or solenoids first. check all the fuses!

@chuckhiggins603 2 года назад

Great video. All the fuses checked out with continuity. I put it back together, plugged it back in, and voila! it's now working. I think that it must have been the first step that fixed it! Unplugging it and plugged it back in... LOL...

@rockinroll817 Месяц назад

Dan, My Kenmore 500 series dryer would run but not heat. I know nothing about voltmeters. Your tutorial was EXCELLENT!! I got a voltmeter with the audio. By the time I got to that thermal fuse and saw it was shot, I felt like laughing out loud!! Your video couldn't have been better or simpler. Thank you so much! I subscribed!

@DantheFixitMan Месяц назад

@@rockinroll817 Love it! So happy to hear you got it fixed! Thanks for subscribing! Take care, Dan

@whliving Год назад

You saved me $150 just to get the repair guy to show up plus whatever else he charged. Easy and straightforward education that made it quick as easy to repair…. And it only cost $15 for the part local. Thank you for the help. 🎉

@zemel18 3 года назад

Thank you. Thank you. This video was perfect. My thermal fuse was the culprit. Replaced it for $5 and now the dryer works. No repairman needed.

@jenniferwagner9347 2 года назад

Thought you might like to know this is still helpful four years after you first posted it. My dryer was running but not getting hot. I don't have a multimeter and thought it was worth a shot to try replacing the thermal fuse as you described rather than spending the money for a meter. I don't like calling repair guys to my home when I can avoid it. Plus I'm just getting over COVID and didn't want to risk exposing anyone. Did I mention that it cost me $8.18 for the part and same day shipping from Amazon? Once you account for the 25 cents in change and three fancy buttons I found behind the dryer, I figure I'm only in $7.48. The floor behind my dryer has never been cleaner (it was gross!) and I couldn't be more pleased that your video helped me fix it myself. Thank you!

@jenniferwagner9347 2 года назад

Damn it! I fixed this last week by replacing the fuse and it's running cold again. Will pick up a multimeter and check the temperature switches. The vent hose is clear but I'll triple check it and see if I can get the back cover for the vent screen all the way off this time. I fished out a thin sheet of lint from there..maybe I missed some. Nothing is glowing when I look through the front access hole - same as last time - but she fired right up once the new fuse was in. Only lasted one or two cycles though. The replacement fuse was BlueStars brand ordered from Amazon. I ordered another pack (two this time). Happy for any additional feedback...and that I already cleaned behind there last week!

@nathanparr6862 2 года назад

I so appreciate walking through ALL the parts and how to use the multimeter so I wasn't left guessing. 15 minutes and $15 from the local parts store. Amazon had three fuses for $6 but I needed my dryer back today. I perfect tutorial.

@xRider_1krr 4 года назад

Continuity pen $8, Thermal fuse $12, and a few screws.... thank you for this video!! I was able to fix my dryer for a very small cost. You're the real MVP brother!! Lol

@DantheFixitMan 4 года назад

Thank you Roy! Glad you got it fixed. Take care, -Dan the Fix it Man

@mandyn2991 Год назад

Thank you for a great video! My husband was busy, so I was able to watch your video and diagnose the problem!!! We ordered the part and he put it back to together!!! We are back in business. I appreciate your help!!!

@briceharris8116 5 лет назад

Thank you. Great information. In my case the element never lit. The thermal fuse was blown. Your video saved me a service technician coming out. Well shown and explained.

@zombie-kb2wq 3 года назад

Easy. TY from my friends widow

@nastypyro 6 лет назад

This was great. Followed it exactly. Come to find out it wasn’t the fuse but the vertical lint trap was full! Cleaned all the crud out and now works like a charm! Thanks again! Subscribed!

@alexanderdgray 2 месяца назад

Dan--I have a series 70 Kenmore, but this video was perfect in every respect. Got back there (not easy for me), took off the back, grabbed the multimeter and next thing you know, my dryer is back in operation. I think the fuse blew because it's too damn hot and it was a cleaning day and we were running it non-stop. Sent you ten bucks to your Venmo--least I can do.

@DantheFixitMan 2 месяца назад

So nice of you! Yes, I got the Venmo, thank you so much! Glad to hear you got it figured out! Take care, -Dan

@Michael-bl4no Год назад

Thanks man, my multi meter was shot but I gambled on the thermal fuse.... just replaced it and it works! Saved me some $ at a time I can’t spare any!

@WarrenHenry 6 лет назад

Thanks! Well shot, well explained and saved me the $125 "diagnostic fee" I was going to have to pay! Thanks again

@loraparral5079 Год назад

Thanks Dan, this really helped save us a lot of money. Just took a little time and about $5 to get us up and running again.

@DantheFixitMan Год назад

No problem, So glad to hear that my video helped you out!

@jonbeams9786 2 года назад

I did the basic check. Pulled it out, removed the hose, it was clogged. Then turned it on. And still blowing cold. So will do continuity test next. Then find out which part is bad. Thanks, fir such a direct, and infirmary video.

@davidvickers41 2 года назад

Nice clear and simple description of diagnostic steps. Thank you

@markbonto8546 5 лет назад

Walt is exactly right on - EXCELLENT video! Thank you Dan!!!!!

@mattstringham5056 4 месяца назад

Thank you for the video. I had the exact same problem you showed in the video. You made it easy to diagnose and fix. Much appreciation!

@DantheFixitMan 4 месяца назад

Glad to hear you got it fixed! Happy to hear my video was helpful! Take care, -Dan

@rafaocaborg 2 года назад

Dan, thank you very much for this useful video. I followed every step of the video and got my dryer working perfectly again.

@4STEVEJOY34 5 лет назад

20 min. after watching this video it was fixed. You nailed it. Now I just have to wait for thermal fuse to get here.

@scottpfeifer291 Год назад

You’re the best! Thanks for reviewing all the limit switches and possible causes. You made the diagnostics and repair simple.

@DantheFixitMan Год назад

Glad my video helped you Scott! Thanks for watching! -Dan the Fix it Man

@jeremyalder2845 3 года назад

Dude! Thanks for the video! All my fuses checked out as good. I took off the dryer vent panel that went to the blower. Yikes! Full of lint. I did clean it up with water and dried it in the sun. Put it back together and turned it on and it heated up quick! I think the clog was the issue! Saved me $750 bucks for a new one!

@domerpyle2949 4 года назад

Well done! It was hard to find info on our old gas dryer. Thank you!

@lynncohen5877 5 лет назад

Quickest and easiest fix ever, thanks to this Dan the FIXIT man video. Works great now!

@007ayala 4 года назад

Thank you so much for adding this video, you saved me over over 100 dollars. My problem was thermo fuse, 14 dollar part in town and problem fixed.

@DantheFixitMan 4 года назад

Glad to hear you saved some money Juan! Thanks for watching! Take care, Dan the Fix it Man

@raymccarthy6002 5 лет назад

Super helpful. Better than any other video I found. Cheers!

@Gablerdan 2 года назад

Excellent DIY video for this dryer! Thanks, Gabe

@missmpromotions 2 года назад

Thanks so much. Great video and thanks for the multimeter refresher that helped so much! unfortunately I have now narrowed it down to the heating element. All fuses and thermal fuse has continuity. Dryer is 23 years old. Changed out thermal fuse a few years ago. hopefully the element is the culprit. If not time for a new used Kenmore 80 series if I can find one. :)

@CC-qg8wu Год назад

You're the Man. Yup, mines a busted Thermal Fuse. Hope I ordered the right part #.

@davidblack4650 8 месяцев назад

Just helped me troubleshoot mine. Didn’t have a multimeter, so I just jumped the two wires and it fired up. Thanks

@rjbrosky 6 месяцев назад

That was a great video. I am going to give it a try now! I will let you know how it went.

@anonymoususer1952 Год назад

Very informative and helpful. Mine was the metal vent assembly had debris in the bottom, restricting the blower and therefore the motor itself. Cleaned everything including the motor with contact cleaner. Works for now. Hoping I dont have to go back in there and replace the motor.

@XBbit0xKbronsit0x13X 4 года назад

Thank you for all the clear steps.

@GLACIOUS13 Год назад

This is great! I haven't tried it yet but have no doubt that it will work. Very clear instructions.

@eliyahulakes7786 3 года назад

Thanks a million! Everything was exact 👍. One word of caution though: the metal edges of the lint trap container are extremely sharp. I sliced my finger working it out, but found the fur ball at the bottom of the opening to the exhaust that caused the over temp.

@jayi836 4 месяца назад

Thanks for posting this! Sending a virtual HI five.

@radchander 2 года назад

Thank you very much. One thing I would like to share is using corrugated flexible aluminum exhaust duct. In many jurisdictions it is not to code, and for good reasons. The plain ductwork is not that expensive, and is worth every penny.

@sabinobarrera3420 Год назад

You are the best , save me from spending $ I was about to buy a new dryer Thank you , thank you!!!!!!!

@walturban9945 5 лет назад

Yes, EXCELLENT video. Solved my problem as well. Thank you very much!!!!!

@dannewbold1385 5 лет назад

Thank you Walt! Glad to hear my video helped you out. Take care, -Dan the Fix it Man

@funtimess2995 8 месяцев назад

You saved me a ton of money!!! Thank you!

@scottvanthof8025 3 года назад

Thanks man , I have a Amana gas dryer and mine got real hot than mine just blew so I have mine on order . Mine looks like your Kenmore . Thanks a lot at least I don't have to buy a new dryer . I had alot of lint in my trap and hose too , my daughter is always doing laundry and she doesn't clean even the pull out trap out . Very nice and well done video , Thanks man !!

@vicdepasse8713 Год назад

thanks for explaining a simple DIY fix.

@DantheFixitMan Год назад

You’re welcome! Thank you for watching. Take care, Dan the Fix it Man

@caminokid2656 2 года назад

Thanks for your help. Saved me some and gave me satisfaction of fixing myself. 👍

@itswitz 6 месяцев назад

This worked, thank you! Great excuse to clean the dryer vent as well

@DantheFixitMan 6 месяцев назад

Glad to hear that it worked! -Dan

@peterhofman7188 2 месяца назад

Thanks Dan for this Excellent Video!!

@62impalaconvert 6 лет назад

I believe the 3 "limit" switches are self-resetting. They will only open when the dryer is in use and overheating. Checking them cold will show them closed but not show whether they are opening when hot and shutting down the heat.

@mustangjoe8352 3 года назад

Thanks for making this video you save me a ton of money

@TheHateuguys 2 года назад

Thank you man! Fixed in 20 minutes.

@luisp8220 4 года назад

Thank you, very well done and easy to follow.

@bhg475 2 года назад

Thank you very much Dan for helping me replace the thermal fuse on my dryer could not have done it with out you you are the man 👍

@Antzzz_Manzzz 2 года назад

Great video 👍🏼. Going to do diagnostic on my dryer 🙏🏼

@tomakafrankconlon3207 Год назад

Great video. Very well explained. My dryer makes warm but not hot air . Not blocked with lint anywhere. Any ideas. Cant afford to buy a new dryer now. Having said that its almost 20 years old so maybe cant be fixed.

@condor5635 2 года назад

Great video. I’m actually surprised that the thermal fuse allows it to even start and energize the igniter. Usually when the thermal fuses fail they shut down the entire machine. Seems like a waste knowing that the thermal fuse is blown and still trying to ignite from a design perspective. As a recommendation any time you can replace the gas coils on the gas solenoid go ahead and do it. They’re like 10 bucks they’re easy to replace and they fail intermittently and are hard to diagnose. Replacing them is a great proactive maintenance while you’ve got the machine taken apart. So easy to replace couple of bolts they slide right in over some metal columns and will save you a lot of hassle on a gas dryer. Thanks for the video

@d.aardent9382 Год назад

Good recommendation, once i saw how cheap all the replacement parts were, i decided to go ahead and just change out everything as ive had it apart once years ago to change the belt and felt drum seal and removed and repaired and cleaned the entire exhaust duct assembly but didnt have any other problem. So this non heating deal just suddenly happened , a few dats ago it worked fine. Figures.. my tv picture went out and ive got to fix it and haven't had time. Lol So best idea since this thing is so old to just go ahead and replace all the different fuses and safeties and igniter and gas valve solenoids. I really wished id done the burner parts when i had the entire drum out last. I thought then i should do it but i couldn't wait anylonger to get it back in action as we were backing up a lot of stuff needing cleaned. I need to take time to put in my clothesline poles.

@fix-it-right5187 2 года назад

Thank you so much for the well explain video.

@fix-it-right5187 2 года назад

Thanks again Dan for the video. What happens if the machine doesn’t light up at all when you turn it on? It it’s only the thermal fuse that doesn’t have continuity in the back?

@christophermorgan7257 5 лет назад

Thank you Dan! I have the exact model and the exact problem. Your fix was perfect.

@epd807 4 года назад

Great video Dan, Thank you!!!

@vanshankguitars 4 года назад

Thanks for the big save! You da man!

@jimgottberg1975 2 месяца назад

Great video and it fixed my issue! thank you!!

@DantheFixitMan 2 месяца назад

@@jimgottberg1975 glad to hear! Take care, -Dan

@Tom8734511 4 года назад

Thank you so much! Excellent advice. You directed me right to my problem!

@mattross2968 Год назад

Just did this fix. Great video. Thanks!

@johnnawodylo5997 5 лет назад

Great video! Very helpful! One question... what if once in a while the solenoid still opens and the flame comes on, but then it also fails as well (more often than not)? Could a bad thermal fuse allow the flame to occasionally kick on? I would really appreciate your thoughts on this. Thanks!

@mrobvious1100 Год назад

Thank you for a concise and informative video. If I may ask one question can you put those wires on backwards as far as the fuses. I guess I am referring to a car battery post scenario. For instance the red wire was on the top male prong and you accidentally put it on the bottom male prong of the same fuse does that affect anything. After watching this video I am going to attempt to figure out why my daughter's was 70 series gas dryer does not get hot. This was a big help. She also informed me that she started the dryer and went to bed around 10 p.m. and woke up the next morning to get her uniform out and the dryer was still running so I'm guessing some sort of a timer issue with the knob on the left the big knob and I'll have to research that

@horacioguzman6029 Год назад

Great video. It solved my problem…

@Ed-oo9th 4 года назад

Perfect. Well done video and tutorial. Thanks for helping me save some $$$$

@frankjpiercy2850 4 года назад

Thank you, thank you, thank you, Just saved a lot of money

@MrUsaer 4 года назад

My elderly mother has the same exact dryer. The igniter does NOT glow at all BUT the igniter tested good. It has full continuity. So, it is possible that one of the sensors or fuses in the back of the dryer that you tested in the video would prevent the igniter from coming on? Or what else could it be. It is late and I am just trying to figure this out so I can start testing more tomorrow. Will check back tomorrow in case you got to see this

@t1yup3 5 лет назад

Great information , solve my problem thanks!!!!

@makloon Год назад

Thank you sir. Great video.

@pdgearhead3504 6 лет назад

Excellent video and explanation. Thank you!

@jeremyalder2845 3 года назад

Dan the fix it man. I just cleaned out the dryer and checked the fuses like you showed and they all checked out as ok. Once cleaned, I turned the dryer on and it heated up quickly but I had no clothes in the dryer. I just ran a load in the washer and put them in the dryer. The dryer ignitor lit up but the gas valve did not open to heat the dryer. Any ideas as to why it worked with out clothes and not it is not with clothes?

@josephalvarado4403 5 лет назад

THANKS DAN-YOU THE MAN!!!! NO MORE SOGGY BOXERS!!!! 😆

@aaronb825 3 года назад

lol same here

@johnhachicho2174 5 лет назад

thanks man you pin pointed my problem .fixed ,,,,thankxxxxxxxxxxxx

@dannewbold1385 5 лет назад

Hi John, No problem, happy to hear it’s fixed! Thanks for watching! -Dan the Fix it Man

@adriandrenalin6716 5 лет назад

Excellent video

@apuzyr 5 лет назад

Excellent video!

@miscaro715 2 года назад

Great instructional video, my 80 series pilot light keeps coming on and shutting off, do you think that could be the same issue?

@michaelwillis7741 2 года назад

Totally worked. A $5 repair.

@brianperkins6121 Год назад

If either the high limit or dryer outlet temperature thermal fuse fails , the corresponding cycling "Thermostat" or cycling "High limit" protector next to it "must" also be changed , as either cycling thermostats should have opened and cut off the heat before it it reached a high enough temp to blow the thermal fuse, As said its always a restricted air flow issue that seeds the failure of either thermostat by forcing them to cycle hundreds of times , if they fail in a manor that causes the either cycling thermostat to fail to open , the thermal fuse is there as a safety to prevent serious thermal runway .

@SimpleInformationINC 4 года назад

Awesome video, but be careful using that harbor fright cheapo meter. I've had them show the wrong amounts in the readout.

@vivekpatil754 6 месяцев назад

Thank you so much for the video

@Holloway418 11 месяцев назад

That was Soooooooo helpful...thanks

@talschuricht4847 Год назад

thank you...great video

@hectort7760 Год назад

Thanks for the video! I have a question, i replace same part it works for 30 minutes and again no heat!

@DantheFixitMan Год назад

Hi Hector, It is important to make sure you clear any blockage in the dryer vent system as that might be causing the thermal fuse to blow. Make sure to check the ducting and/or ventilation to outside as well to make sure there's no blockage there. Best of luck to you! -Dan the Fix it Man

@dustinwarren470 2 года назад

Dan I'm counting on ya here buddy lol. New subscriber here.

@typhoon320i 2 года назад

Another Video by Sears, seems to say, that if the thermal fuse was bad (the case here) your ignitor shouldn't glow at all.

@weejkeneej5971 8 месяцев назад

great video!

@enzoo616 4 месяца назад

Is there a possibility of the timer, dryer cycle thermostat, & the dial going bad at the same time??

@pacohernandez1922 Год назад

What's the hose/pipe on the bottom under the back panel? not the duct

@Malco47 4 года назад

Thanks friend!

@YOHONOMOTO 6 лет назад

Thanks for the video. I checked all three of these for continuity and they all had continuity. Why else might my dryer not be getting hot?

@DantheFixitMan 6 лет назад

Could be the solenoid coils not opening, or a bad igniter. (There's other videos on here on how to test them). Best of luck to you. -Dan the Fix it Man

@jasonbird138 4 года назад

Hi Dan. What does it mean when you look through the hole and see no orange glow? Pilot light not working?

@irocitZ 3 года назад

Good question 🤔, no answer after 6 months

@alexhatcher8812 3 года назад

most likely bad ignitor and/or. bad flame sensor....

@MoeSizzlac01 Год назад

@@irocitZ For me, It was still the thermal fuse. Don't know why the orange igniter didn't come on but after taking apart the back and cleaning everyrthing up and testing all the components, the thermal fuse was indeed the issue. I jumped a wire across the thermal fuse to see if it would ignite and it did. Granted, my Kenmore 80 is slightly different than the one in the video (only 1 high limit switch as opposed to 2).

@walterzimmer1352 2 года назад

Thank you

@Michael-bl4no Год назад

Did you turn off the gas before starting?

@greenplanet4010 Год назад

Fixed my dryer thanks to you 🫶🏼

@Msibme 4 года назад

Thank you for this video ... I am using it to repair my Kenmore Gas Dryer. When checking the elements how do you know it is good ... it is just because there is some kind of input? or does it need to be a certain number?

@warriorlabz4045 10 месяцев назад

Hi Dan.....Great video pulled the square plug in front and NO FIRE. I removed the back and tested the uppers and they were find.....YES the Thermal fuse was bad. WILLL THE BAD THERMAL FUSE CAUSE THE FRINT FIRE / IGNITER NOT TO WORK?

@DantheFixitMan 10 месяцев назад

Yes

@warriorlabz4045 10 месяцев назад

OFF TO GET A NEW FUSE AND LETS SEE IF THE BAD BOY WILL FIRE UP AGAIN. THANK YOU DAN :) @@DantheFixitMan

@warriorlabz4045 10 месяцев назад

$7.50 later I now have a prefectly good dryer up and running. A HUGE THANK YOU TO DAN FOR SHAING HIS KNOWLEDGE AND INFO. I am religious about cleaning the lint trap after every load. From now on....every year that back panel will come off and blow out all the lint. could not believe how much there was. cheers to all :) @@DantheFixitMan

@DantheFixitMan 10 месяцев назад

@@warriorlabz4045 So happy to hear you got it fixed! Thanks for letting me know. I appreciate your nice comments as well. Take care, -Dan

@sheikhkhalid5969 4 года назад

thank you very much. was very well commented. Must have gotten an A in physics lab:) God Bless with more learning:)

@FrederickCNichols 4 года назад

Thank You!

@Peter-pv8xx 4 года назад

Tested everything and all is good, tested igniter which tests good also, does not glow, I'm stumped, it is an older Kenmore that never gave me trouble, what am I missing?