KitchenAid Mixer Diagnose And Repair

Подписаться 1,2 тыс.

Просмотров 122 тыс.

50% 1

KitchenAid mixer that wouldn't turn on after letting out the magic smoke. Tearing it apart to find the broken piece, fixing it, and putting it back together. For once, the whole beginning to end is on video.
Disclaimer:
Due to factors beyond the control of this video and/or RU-vid channel In-depth DIY, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. In-depth DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. In-depth DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of this channel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained

Опубликовано:

4 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 61

@BringItOn31124 10 месяцев назад

If the machine smoked, usually it had a short like this one. If the motor suddenly stops working, without any smoke, usually the brushes need to be replaced (make sure angled side of brush lines up with machines internal notch). If the machine pulses sometimes or runs at slow speed for short period and shuts off, usually it's the phase control board. Make sure small contacts (little rivets) on the speed control plate are in tact. They can pop out over time. If there's a problem with speed control, could be speed control plate or speed control lever. If motors runs but padle doesn't turn, the nylon worm gear needs to be changed. Hope this helps someone.

@Californiasnow 10 месяцев назад

My motor runs but paddle doesn't turn. Where does one purchase the nylon worm gear?

@Lilywrite 8 месяцев назад

This was incredibly helpful, thank you!!!

@BringItOn31124 8 месяцев назад

@@Lilywrite You're welcome.

@Puffers98 6 месяцев назад

Hi mine doesn’t work anymore. I took out the bushes and when I take out the one same side as the release mechanism and put it back on, it pulses for about a second and stops again and won’t come back on. Any advice please

@BringItOn31124 5 месяцев назад

@Puffers98 I would change the phase control board. While you're in there you should probably change the speed control plate. I'm suspicious that the plate had something to do with my board going out. I also suggest buying genuine KitchenAid parts. Around 30 bucks shipped is what I paid for both. The speed control will have to be adjusted but nothing super complicated. There are good videos for this.

@m.rutledge1599 9 месяцев назад

Watched this video for instructions on how to take it apart, and told me what was wrong with mine, the nylon drive gear was intact toast. Amazon supplied part and food safe gear grease ordered and installed. Thanks. Works as advertised once again.

@socalhardtailmtb4194 6 месяцев назад

Good info for disassembly. My wife’s would not stay in the off position on first try. I found the screw for the on/off speed lever was slightly loose. To tighten, you have to completely disassemble like in this video. I removed the lever screw and added a drop of loktite. All good now.

@jimdowney511 2 года назад

had a "smoker" that i gave away. wish i had it back now, good catch!!!

@ApriliMille 8 месяцев назад

Needed this, Thanks!

@drrous9917 5 месяцев назад

Great job on the video. 🎉

@angelvalle4426 22 дня назад

Good job Bro.👍👍😱

@gailreed-fz6em Год назад

Do you think the plastic gear at the front could be used to replace the one that runs the main mixer, since I do not use any other attachments.

@terrionk8201 4 месяца назад

Do you know how to replace the spring inside the mixer? If so, will you make an instructional video please and thank you.

@donhammond1452 2 месяца назад

Big help! Thanks

@Gillettesgarage 3 месяца назад

Thanks for info.

@ArturTx 9 месяцев назад

thanks a lot!

@zoetekruimels Год назад

How do you punch out the pin?😅 trying to investigate but get stuck at step one...

@m4tthi3u 3 месяца назад

help

@mrprfct7069 Год назад

I need the plastic gear on mine. Where can I order it from ?

@callimcclendon3085 5 месяцев назад

So I had one that smoked but would still work. I took it apart and all gears looked good, motor looked good. I cleaned out some of the grease as it seemed to coagulate due to not being used for a few years (it was a gift). I put everything back together and now it won’t even turn on. Any idea what I could have done??

@nightwolf48nm 4 месяца назад

Did you remove the two plastic screws on each side of the dome?

@pk2ccs Месяц назад

Probablemente sean los carbones si los llegaste a sacar, ellos tienen una forma particular de colocar.

@siswoyohardjono2088 Месяц назад

Terima kasih Bos

@bethmarquis8592 7 месяцев назад

I have taken off all of the necessary screws and for the life of me I can’t get the top housing off. I had grease leaking out the back for a while and I’m wondering if that’s why it’s so stuck. Any advice on how to get it off or is it just a muscle it kind of thing? I tried prying it up as well and it moves some but goes right back down.

@BringItOn31124 5 месяцев назад

You punched out the pin that holds the planetary on? The top can't come off without removing that pin. He shows how to do it at 1:32 of the video.

@BringItOn31124 5 месяцев назад

Also, the end cover has to be removed because the wire strain relief has to be removed to allow the top to be separated from the bottom.

@MsLori1973 10 месяцев назад

Tha k u i just bought minr n used it twice. I out bread dough in and it was fine n now it flshut off and feels hot. Kimds smelt a kittle soemthing but not really. Im pretty handy n i know to shut thingd off if thrybsre burning. I noticed when i forst used it my slide button wouldnt turn it on id have to slide it back n forth a bit or twice ans it woukd start up. So im imagining with all the jumoing on the counter its done thr same. But it never did turn on right the fsy i got it. Strange. Me n my gf got thrm at the same time. All my stuff is on her laptop in my email but she passed away n i never used mine again. Just the one day. I dont have access to the email for my coverages either. Maybe if i call them. So id like to check mine out without ksoing warranty. We bought ours a coupke yrs ago tho. So not sure the warranty in them. Im kimda mad mines a professional 5 cost me over a grand so im not happy.

@hvacexplained9341 Год назад

I’m taking a look at my mother-in-law’s mixer. I can hear an obvious whirring sound coming from either a set of gears going bad or bearing issue. Just checking out this video to see what I’m getting involved with. It’s just mechanical just take it one step at a time really.

@m.georgieva6239 Год назад

Smeg mixer! I need help! Has anyone come across a video of the machine taken apart? If yes, share? I want to see what it looks like inside! thanks

@pablitoarceo8776 Год назад

how do you replace capacitor of classic kitchen aid mixer

@dorisdillon643 8 месяцев назад

Do you buy vintage kitchen aid stand mixers for parts or to repair & resell?

@in-depthdiy2123 8 месяцев назад

I don't fix them professionally, this one was fixed for a friend.

@oTouchMe Год назад

My mixer turns on but it doesn’t spin. I’m thinking it’s one of the gears. I tried taking all the screws in the video but when I got to the motor and the top part, it seems to be stuck as if it was glued on. I tried prying it open with multiple flatheads but nothing works. I’m not sure what to do.

@rgemail Год назад

Did you punch out the pin and take off the lower mixing housing too?

@BringItOn31124 11 месяцев назад

Did you fix your mixer?

@dougfoster445 Год назад

Boy really wish it went into how to take the motor apart. Mine isn’t working. Can’t figure out how to get access to the rotor and stator to put a meter on it. Do these things have fuses?

@jerri4Freedom Год назад

This one tells you how ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-N7_qfIqX0dI.html

@dougfoster445 Год назад

@@jerri4Freedom thank you!

@charlesneal4603 11 месяцев назад

Why didn’t you coat gears with some grease?

@abegaelbesa8683 5 месяцев назад

May available po ba kayong sencor stand mixer STM3620HW

@Creations-hj2kq Год назад

Funny my dough mixer also has one lock washer but the other screw has no lock washer... i will put a lock washer when i assemble it back.

@peterjshep Год назад

he mentioned it was probable cheaper to only have one - for kitchenaid

@jackiestrain6241 Год назад

Any way you can help me with fixing mine?

@BringItOn31124 11 месяцев назад

Did you fix your mixer? If not, what where your initial symptoms.

@ElGoogKO Год назад

So...this sounds like a manufacturing defect, a bad engineering design, that allows the wire to be caught in there. Nice video.

@BringItOn31124 11 месяцев назад

You can see in the video that the black wire was accidently pinched behind the trim ring. That wire is oddly long because I have 2 mixers and neither one has a length of wire that can even come close to being pinched behind that ring. I don't think this is common at all.

@navojoitason1556 Год назад

My mixer was perfectly working and then start slowing down until completly stops.. Do you have any idea what can be wrong? and that you in advance for your help

@in-depthdiy2123 Год назад

I can't remember off hand, but the motors could have brushes. The brushes are small graphite blocks and wear down over time, or become dirty and prevent clean contact with the motor. They usually can usually be replaced. That might be something to investigate, but will probably require tearing the machine down completely. Good luck!

@j.d.3269 Год назад

@@in-depthdiy2123Simple, just unscrew one big black plastic cap on both sides of the housing.

@BringItOn31124 11 месяцев назад

Did you fix your mixer?

@navojoitason1556 11 месяцев назад

@@BringItOn31124 I did replace the brushes but the mixer still wouldn’t work correctly, so I sent it to a technician for repairs and was told that the control board was faulty aswell, so that had to be repaired (some connections had to be re-soldered). I can say the initial problem was solved but now the mixer’s speeds control don’t work anymore - adjusting the speed lever doesn’t change the speed at all. 😏

@BringItOn31124 11 месяцев назад

@@navojoitason1556That slowing down and then completely stopping is a classic symptom of a bad phase control board. The tech sent your mixer back without resetting the speed controls? They took off the speed control plate to get to that phase control board that they "fixed".(Probably just replaced with a new one) That means that the speed controls would have to be reset. All that should have taken less than an hour to do and about 20 bucks for a new phase control board.