Liquid Blasting at Eastwood to Remove Paint & Rust - Dustless Blasting with a Pressure Washer!

Подписаться 515 тыс.

Просмотров 207 тыс.

50% 1

In this video Matt goes over the benefits of Dustless Blasting!
Get a Blaster: www.eastwood.com/liquid-media-...
The Eastwood Liquid Media Blaster is specifically designed to use high pressure water from a pressure washer as a source for powerful dust-free abrasive blasting.
Powerful Dust-Free Abrasive Blasting
Efficient Siphon Feed Gun
Removes Paints, Coatings and Loose Rust
Replaceable Wear Components
It features an efficient siphon feed gun with replaceable wear components. The Eastwood Liquid Media Blaster provides a dust-free method to strip away old paint and coatings, body fillers, accumulated dirt and loose rust leaving a clean, bare metal surface ready for damage repair or painting. will work with medias 30 grit or finer.
Pressure Washer is not included.
For more information on Eastwood products visit www.eastwood.com or stay connected with the team via:
Facebook - / eastwoodcompany
Instagram - / eastwoodco
Blog - www.eastwood.com/blog
Eastwood has everything you need to do the job right when you're restoring a car, truck or motorcycle - from welders to paint and everything in between.

Авто/Мото

Опубликовано:

8 авг 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 80

@bobking1867 Год назад

Cheap "bone dry" play sand from any store works great. You can't have any moisture in it or it will not feed. Make sure you position the sand blasting attachment tip on the wand so the hose faces up, and not down. Water will want to run down into the sand suction hose and will clog the flow of sand. I black tape the suction hose for the nozzle to the wand so its always facing up when in use.

@DBIIIStudios 2 года назад

I bought a cheap $25 one from Amazon. It’s the same thing just not nearly as quality. Plastic vs metal. I blasted an entire boat with it and it worked amazingly. If I ever need this again and the one I have breaks, I’ll buy a quality one like this with a replaceable nozzle.

@MarkSchuster-ym3iy 3 года назад

I made the exact system. But I found adding a power pot and a ball valve you can control the water media better. You can use that wet or dry

@valbien-aime7965 4 года назад

Would something like this be able to knock of rust that already flaking and peeling?

@jimdrechsel3611 4 года назад

I cannot find the RU-vid or Facebook for the live sessions. Have they been cancelled? I also looked on the website and mentioned it when I called Eastwood. They knew nothing about it. Please provide the information.

@fuongy.visuals 6 лет назад

Does it work on tattoos

@stevefindlay7155 2 года назад

Is this available in Australia? Also, is the media recyclable, can it be swept up and dried out and reused? Cheers👍🇦🇺👍

@anthonycolasessano8855 4 года назад

Ik a heat gun softens body filler and will make it very easy to scrape off

@MrRenoman2011 7 лет назад

Looks like an awesome product

@MarkSchuster-ym3iy 3 года назад

That’s basically a water symphony filter you can get at any hardware store. But yeah the wet blaster is so much better than dry

@kenkaye9765 7 лет назад

What's the unit worth

@djsbuds123 3 года назад

Do they answer questions?

@nathanmciver6496 2 года назад

Can't wait till my black powder coat arrives, satisfied with the paint, they should have an easier way to track the package on the site! You should be able to type in the search "my east wood orders" You don't need variations between companies with tracking, thats why I like that at least amizon has that option!

@ninogonzalez5045 7 лет назад

Will it go through old body filler?

@joeycrackedcorn3707 6 лет назад

I have a craftsman 2800psi gas powered pressure washer I think it does 2.3 or 2.4 gallons per minute will that be enough to power for this system?

@accidental_relevance 3 года назад

3.5 gpm is recommended

@vin605 6 лет назад

Cool product

@accidental_relevance 3 года назад

I see the 10/40 glass blast media which I presume is the proper media to use with this tool ? But shipping is $50 ? Is it because the weight, 50lbs ?

@JamesDoylesGarage 3 года назад

If I use the after blast, do I have to clean that off some how before I prime and paint or undercoat? Thank you

@jsnyara Год назад

Yes. You need to clean that off

@jayabbondanza2042 3 года назад

we just got the Eastwood dual sand blaster. Hoping to remove the paint from our fiberglass pool. Any suggestions? We are not having much luck. Thank you

@RatsnestHotrods 7 лет назад

Very cool

@edwardviscarelli7110 6 лет назад

What about stripping off powdercoating? I guessing probably not.

@eastwoodco 6 лет назад

Try Down To Metal Stripper: www.eastwood.com/eastwood-down-to-metal-paint-powder-stripper.html

@tthams73 2 года назад

Aluminum oxide?

@briandobrzanski9831 7 лет назад

Can i powder coat over the after blast

@JonBorpa 7 лет назад

most likely not your going to want it as clean as possible

@iamericg9224 7 лет назад

After your done can u apply epoxy primer or do u have to still sand it then apply primer

@TheRyancamaro 7 лет назад

BodyShopMafia 1992 Usually as soon as you finish blasting as long as it is dry it is possible to epoxy immediately after blasting

@iamericg9224 7 лет назад

Ryan Haslett thanks

@horsemania4356 6 лет назад

spray with POR-15"metal prep", etching primer, keeping, All surfaces wet, for 15-20 minutes, rinse, blow dry, with compressor. keep dry, or paint

@coolio2713 4 года назад

Hello, how You remove the afterblast to paint?

@eastwoodco 4 года назад

It does not need to be removed.

@600miles 4 года назад

The Afterblast looks like phosphoric acid. It is an adhesion promoter and prevents rust. I personally would use Metal Prep - same as phosphoric acid.

@bayouboattrash 7 лет назад

Is there any other type of media you can use with this system?

@patw52pb1 7 лет назад

We have successfully used blasting sand, glass fragments, glass beads, glass powder, garnet, ground ceramic and soda. Also aluminum oxide, but had some difficulty with feeding.

@kbtube8125 6 лет назад

ca-ca.

@elvisacosta6666 6 лет назад

So I don't have a tire changer, but I need to blast the wheels of rust it currently has on it. Can I blast the wheels with the tires on? Simply, would it harm the tires if I were to hit the tires in the process? Can't take the tires off and then blast the wheels because that would mean I would have to leave the car at a garage while I blast the wheels. Trying to do the work myself as cost effectively as possible. Thanks.

@johnalbrittonsr 6 лет назад

Use soda

@benjaminsword9907 6 лет назад

Use heavy tape around the rim perimeter and don’t hold the tip right at the tyre. The rims will blast great

@robertmalone4161 2 года назад

Can you take off paint from a house with cinder block walls with this?

@williamfelts2197 3 года назад

Pressure and volume of water per minute?

@brettblack7049 2 года назад

Said 3.5-10 gallons per minute.

@outdoormountainman Год назад

I have seen this type of media blaster used and when the metal is not dried quick enough you get flash rust .

@MarkSchuster-ym3iy 3 года назад

You need at least 3.5 psi. Get an actual guage at Amazon an oil filled.

@JAYJAYJAY53 Год назад

What specs are needed for the compressor?

@michaelj2505 4 года назад

Will this work for bottom boat paint removal?

@Fishman92 3 года назад

Did you find out if it'll work?

@juliojuarez2705 3 года назад

If I understand correctly, the After Blast will act as a rust inhibitor. Therefore I don't need to apply a primer right away, right?

@joshmartin8856 2 года назад

Generally 72 hours. It's not going to flash rust, but you want to epoxy prime it ASAP.

@youthmanrecords965 8 месяцев назад

Just use phosphoric acid with distilled water diluted %40-60 depending on your strength needs To soak bolts or parts for days do a %20 phos / %80 distilled water Add some hand sanitizer gel to make it adhere to the part and apply with a chip brush from harbor freight

@600miles 4 года назад

Why use Ground Glass instead of sand? I used sand for 30 years until I found out it was a hazard from free floating silicates but with Wet blasting there is no dust.

@quacktony 7 лет назад

I thought it was known that in order to sell a product, you show a demonstration along with introducing it......

@qtleeta 3 года назад

7&9

@motortrain9000 7 лет назад

Hey Matt Missed the live show by just minutes! Now, if you all want to "educate and inspire" us DIY guys, try using more (IE: adequate) protection equipment. Try using a full face and ear guard, or at the least a full face shield. When I use my (just) pressure washer I put on a full Frog Toggs rainsuit and my full face shield. Maybe Eastwood should look into carrying full face gear? Honestly Matt, it wasn't much fun having that stuff all come back at you, was it?

@RJCoAustralia 7 лет назад

Im a diy guy and I couldn't care less common is a given i just wanna see a good product and straight to the point

@brettblack7049 2 года назад

@@RJCoAustralia exactly.

@wd3930 3 года назад

So you need a $1400 pressure washer (@ 400psi 3.5gpm) to work this $100 product????

@joshmartin8856 2 года назад

I would really like to see a compressor / pressure washer combination system. Most guys have a sub decent gas washer (2.5gpm) to push the water, and a decent 80gal/110psi air supply to push the media. Anything bigger, well you would have a pro shop, and a pro blaster. I'm thinking of a cyclone delivery nozzle that combines pressurized media and water in the tip. That would strip your filler. It would just have to be better than sand blasting while someone holds a hose on the work. :)

@zenginellc 2 года назад

My 3.5GPM, 4,000 PSI machine was only $800...

@realtaur 7 лет назад

A 50lb Bag just to do one piece!!!!!!!!!!!!! and what about all the Glass water????

@patw52pb1 7 лет назад

There has to be sufficient abrasive media in the stream to clean. The larger and complex apart to be cleaned is, the more blast media will be required. We have a similar unit that we reclaim and reuse the media continuously. There is some loss, but we generally recover greater than 85 percent. I caution anyone and everyone that uses one of these or similar units to use adequate and proper PPE, especially head and face protection, we experience a lot of return/reflected spray loaded with blast media that ends up on/in the operators face/eyes/nose/mouth/ears/hair, clothes/pockets and in every nook and cranny possible. I recommend a Tyvek full coverage chem (bunny) jump suit, rubber boots, gloves and a full coverage media blast hood.

@acepowdercoating3089 7 лет назад

This is the worse product I've ever bought from Eastwood! Sorry but I had very poor results from my unit. The hose seems to collapse and not allow media to flow threw it. I called Eastwood and they happily refunded my money which was nice.

@Just1Spark 6 лет назад

Its the worst hose type for this application. You can see it kink over edge of bucket in the video. When are companies gonna learn. Build it right, equals less refunds.

@richardredwine6710 5 лет назад

I have this also and like you guys I was less than impressed, I replaced the suctioning hose with a hose made for farm seeding and spray equipment. I think I bought it at Rural King but any farm supply store will have it. It is working fine now, unfortunately companies like Eastwood have to buy Chineses to stay competitive and inferior products are just the norm from there, you have to adapt to overcome.

@ronburgundy7127 5 лет назад

Not impressed by just looking at it

@onegative8887 4 года назад

Looks like it would take forever to do a whole car

@davidcooper6618 4 года назад

Yea im thinking only for small parts, even the core support looks like it took forever. They used 50lbs of media.

@rickyhildebrand114 6 лет назад

Not very cost effective. Probably best at the hard to get at nooks,and cranny's.

@danielfigueroa4725 5 лет назад

I wish i researched this product before buying it. So at a minimum your going to pay 900.00 for a pressure washer that will work in order to use this product

@ronedee 5 лет назад

Rent it @ Home Depot or Lowes for about $60 a day

@600miles 4 года назад

I bought a Simpson 4400 PSI pressure washer for $699 New. It's 4 GPM with a 50' hose. I ordered it from Lowes. Model #: 60843 Watch the vids, you will be impressed.

@AGonzo108 3 года назад

@@ronedee I didn't even know you could rent them. I just called my local HD and they rent em for $100 a day. Good thing I saw your comment. Now I can return my $800 pressure washer i just bought and use those savings towards other things for my project. 73 dodge w200. Thank you good sir!

@brettblack7049 2 года назад

One of the things that makes this product cost effective, is for those who already have a pressure washer, if you don't, then why not buy a dedicated machine for blasting or pay somemeone to do your blasting. It's another option, so don't knock it ;).