Тёмный
No video :(

Low drag sprag and race upgrade for Ford C 6 

Dragracer64
Подписаться 6 тыс.
Просмотров 11 тыс.
50% 1

In this video the Torino's transmission starts to go back together.

Опубликовано:

 

26 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 16   
@joshpowell7113
@joshpowell7113 5 лет назад
Thanks for sharing your builds! Ford content is always appreciated .
@Dragracer64
@Dragracer64 5 лет назад
Your welcome ,and thank you for watching and commenting..
@jglayden
@jglayden 5 лет назад
I broke mine trying to take it back out when it didn't seem to sit quite right. So since my original wasn't too bad, I just reused it and flipped the brass over so any wear was on the outside. Next one I do, I will try to get the original. I saw a video where that plastic just cage just tore up, so I am a little concerned with this anyway. But good video.
@Dragracer64
@Dragracer64 5 лет назад
So far no troubles, but I wasn't impressed with what i saw while installing it. Time will tell. Thanks for watching.
@TheProchargedmopar
@TheProchargedmopar 2 года назад
👍💪
@Dragracer64
@Dragracer64 2 года назад
Thanks for watching.
@bobcuomo5122
@bobcuomo5122 5 лет назад
great video thank you
@Dragracer64
@Dragracer64 5 лет назад
Thanks for watching .
@the_fomoco_man5160
@the_fomoco_man5160 4 года назад
Hello sir, just curious how the BW sprag and the new race with the Torrington bearing are holding up?
@Dragracer64
@Dragracer64 4 года назад
Still holding up.
@0lddragracer426
@0lddragracer426 2 года назад
This video is still very useful, thanks by the way. Where is the best place to buy the Low Drag Sprag, and the Race Upgrade?
@Dragracer64
@Dragracer64 2 года назад
Found mine on E bay. This video is from about 3 years ago. I would have to dig deep into all my purchases , to find the link.
@0lddragracer426
@0lddragracer426 3 года назад
Thanks for showing this video. I picked up some good knowledge. Where did you get the 4 pinion at?
@Dragracer64
@Dragracer64 3 года назад
Glad it helped
@0lddragracer426
@0lddragracer426 2 года назад
I found it on eBay - $325. dollars. I have a GearVendors box for my 67' Ford pickup. GV says to use a 4.11 rear-end gear, so I bought a new one. After thinking about it, I thought...this is not a race truck your building on the street." "It's about 550-600 hp." "The lower ratio planetary would give me the out of the hole gear." "Maybe I should have bought a 3.90 gear instead, and I'd have even more cruising gear." What say you about this.
@Dragracer64
@Dragracer64 2 года назад
I have never own a gear vendors box , so I don't know how high the overdrive is. It all depends on what you want, as far as driveability, vs launching power. Also with that much horse power, if you run street tires, I am sure its going to spin a lot when taking off hard regardless of what the lower gear ratio is like.
Далее
Ford C 6 forward and direct clutch stack clearance
10:30
skibidi toilet multiverse 041
06:01
Просмотров 5 млн
SPONGEBOB POWER-UPS IN BRAWL STARS!!!
08:35
Просмотров 17 млн
Ford C6 Valve Body Shift Reprogramming Kit Pt1
9:55
Просмотров 26 тыс.
How Does a Torque Converter Work?
19:59
Просмотров 4,1 млн
C6 Valvebody overhaul and install
26:44
Просмотров 19 тыс.
Fairbanks R servo for Ford C 6
11:44
Просмотров 11 тыс.
Ford C6 Rear of Trans assembly pt#1
15:42
Просмотров 2 тыс.