Тёмный

MUST WATCH- From A to Z on injector removal when they are seized - Renault Trafic 

OGS Mechanics LTD
Подписаться 5 тыс.
Просмотров 162 тыс.
50% 1

0:30 engine crank but no start
2:00 remove heater blower
2:50 remove engine breather
3:30 rusted diesel injectors
3:40 injector connector rubber grommet missing
4:30 remove injector fuel return pipe
4:50 removed rusted injector bolts
5:00 injector bolt shorter than the rest
5:40 remove injector pipes
6:40 set up hydraulic injector puller
7:20 set up hydraulic piston puller
7:35 injector removal action
8:40 seized injector removed
9:20 second injector extracted
10:40 third injector hydraulic removed
11:32 injector connector water ingress
12:00 stuck injector removal
13:00 install injector puller adaptor on the stuck injector
13:15 broken diesel injector in extraction process
13:30 injector broken half way
14:15 cutting new thread
14:40 extract injector sleeve
16:20 clean cylinder head corrosion
16:40 drill broken injector
17:40 extract injector nozzle
18:00 install new injectors
19:04 program injector codes
19:30 install connector rubber seals
20:00 remove wiper panel
20:22 water drains blocked
20:40 water leak on cylinder head
21:20 reseal wiper panel
OGS Mechanics is a specialised garage workshop based in Finchley Central, London, UK, that carries out repairs, maintenance, ADAS calibration, vehicle security upgrades, engine rebuilds, extraction of stuck injectors and glow plugs, advanced coding and programming for almost all vehicles on the road.
The OGS Mechanics workshop is the one-stop for all your vehicle needs!
OGS Mechanics
☎️: 0208 346 6755
📞: 0790 864 0578
📧: sales@ogsmechanics.com
📌Units 9 - 14 Millers Yard, Rear of 28 Long Lane, London N3 2QG
Our website: www.ogsmechanics.com/
More articles about car repairs: www.ogsmechanics.com/blog/
#renault #renaultvan #renaulttrafic #engine #enginecrank #nostart #injector #rustedinjectors #injectorbolts #hydraulicequipment #injectorremoval #wateringress #cylinder #cylinderhead #corrosion #wiperpanel #ogsmechanics #garageworkshop #garage #autorepair #carrepair #carmaintenance #enginerebuild #injectorremoval #adascalibration #coding #programming

Авто/Мото

Опубликовано:

 

1 апр 2021

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 125   
@d-s-ll2378
@d-s-ll2378 Год назад
This is the most respected mechanic, thanks for showing us the great attitude and professionalism.
@kevinpalmer7452
@kevinpalmer7452 2 года назад
Superb job gentlemen and an impressive selection of special tools a quality repair indeed.
@jonjolliffe7757
@jonjolliffe7757 2 года назад
This is the mechanic that has just sorted my injectors on my 2012 Vivaro. He did a fantastic job, My engine head was far worse than this with all bolts very badly corroded. I couldn't get the van to their workshop so they came to the Isle of Wight. My scuttle panel had the the central bolt broken so water just poured straight on top of the engine. It was this Video that made me decide to call them, Good price as well. Thanks
@patrickpirelli7897
@patrickpirelli7897 5 месяцев назад
How much did they charge you ??
@mksl3894
@mksl3894 Месяц назад
Thankyou for you advice .i need my ijct to replace.thanks .
@thodoriskimoliatis3003
@thodoriskimoliatis3003 15 дней назад
Great job! Thanks for detailed explanation.
@davidharvey8812
@davidharvey8812 Год назад
Thank you for posting. I was told by a Machanic that if a fuel injector breaks off the engine is F@@ked. He said if it does he would give me £300 for a traffic on a 53 with 90 thousand miles. 🤷🏽‍♂️ great work guys !! 😊
@DorinelMusic
@DorinelMusic 2 года назад
Thanks for the help with silicone repair, the cause of the problem, to this model - BIG LIKE!!!
@tracieoliver2307
@tracieoliver2307 6 месяцев назад
These guys are top notch and I can recommend them as they did my van and its run superb ever since!
@dejanfreighter2926
@dejanfreighter2926 Год назад
You are a genius 👏. What a good narrated, slow & full of detail video.Thank you Sir, helps a lot.
@samukbk1475
@samukbk1475 8 месяцев назад
These guys are amazing..they done my car when everyone was saying it’s impossible..
@NafanyaZX
@NafanyaZX 4 месяца назад
Invaluable detailed explanation of what's going on. Thanks a lot.
@michaeldepass7778
@michaeldepass7778 3 месяца назад
Great demonstration, thanks for taking the time to show us
@LifeWorkRestPlay
@LifeWorkRestPlay 8 месяцев назад
Excellent work, very informative & super quality video, thank you.
@lukaszsosen4266
@lukaszsosen4266 2 месяца назад
Professional job we need more mechanics like that 💪👍👍
@user-ic7yh2gf1e
@user-ic7yh2gf1e 7 месяцев назад
got to say thats the best iv seen grate job done.
@pantudino14
@pantudino14 2 года назад
Great video! Very useful !
@frazahmed6168
@frazahmed6168 11 месяцев назад
What is about the tip of the last injector? Where is it? How did you extract it?
@alank616
@alank616 8 месяцев назад
Great video, thanks to you both for sharing
@BrothersGrim2012
@BrothersGrim2012 2 года назад
Great video very helpful 👍👍👍
@Gilespargiter
@Gilespargiter 5 месяцев назад
That was a very good clear video. Thankyou.
@forced-induction
@forced-induction 2 года назад
Really good video. Hydraulic puller ftw
@viktorbraun5303
@viktorbraun5303 26 дней назад
Exellent video and very detailed. Thank you
@MrMadenuff
@MrMadenuff 29 дней назад
Very informative video, thank you.
@everythingeverywhereanyone
@everythingeverywhereanyone 2 года назад
Brilliant video , such hi quality and nicely explained. Was going to buy a vauxhall van but after seeing this I'm unsure.
@patrickpirelli7897
@patrickpirelli7897 5 месяцев назад
I wouldn't ever buy another never 😱
@dax6376
@dax6376 Год назад
Very informative, thanks ❤
@davidbonnett5441
@davidbonnett5441 2 месяца назад
Fantastic video.
@jimt8667
@jimt8667 2 года назад
Superb video
@kelleypack1000
@kelleypack1000 Год назад
Wow great job
@michaelbrennan8451
@michaelbrennan8451 2 года назад
Excellent video you make it look so easy.i suppose once you have the tools and the head for this type of repair your laughing.
@anthonyoconnell9389
@anthonyoconnell9389 Год назад
Great job well done
@kevinbarnesworship5517
@kevinbarnesworship5517 Год назад
Thanks for this video. Great help... Do you recommend coating the injectors in copper grease before Installation?
@alvislacitis5019
@alvislacitis5019 2 года назад
2:16 good catch lol
@dominiknowacki5586
@dominiknowacki5586 Год назад
Hi. Amazing video . What you can do if the washers which keep the injectors cant get out as the bolts completly rusted . Not possible to put any socket.
@RD-650
@RD-650 2 месяца назад
Well done 👍
@kennethtalbott2233
@kennethtalbott2233 5 месяцев назад
great job.
@lgtweewielers
@lgtweewielers 2 года назад
Where to buy this tool , nice work !
@dootsize
@dootsize 3 года назад
were did you buy the tool and how much ? cheers paul
@pizzaro4541
@pizzaro4541 2 года назад
brilliant video thank you
@BensWorkshop
@BensWorkshop Год назад
I do like your hydraulic lifter, though I made an adaptor to go on my injectors in my Jaguar X type (same as Ford Mondeo MK3) and can then hammer them upwards. Mind you mine get tar seized rather than rusted in.
@TM-tz1nx
@TM-tz1nx Год назад
Super film!!!!!
@lizardking5002
@lizardking5002 6 месяцев назад
Hi nate great video. What make is romoval tool please
@JoeNunes345
@JoeNunes345 5 месяцев назад
Thank you for posting this informative video. At around the 12 minute’s mark it was decided not to apply any more pressure, to prevent the top of the injector from snapping off. At what pressure do you decide to stop and change methods? Kind regards, Joe.
@faroukkhan6777
@faroukkhan6777 9 месяцев назад
Excellent tools nice job ,,, Mercedes Benz, Nissan,, Renault's,,, BMW, and so on ,,,, hard to remove,,,, but it's all about vehicles not being maintaining,, like old days,, before,,,💪
@surfreadjumpsleep
@surfreadjumpsleep 2 года назад
thanks for the video! Now the trick is to find a garage with this tool.
@MARKH-er5bl
@MARKH-er5bl 3 дня назад
When you drilled out the broken injector.It looked like part of the injector nozzle was left behind....when you compared it to the other injector it was a lot shorter where the spray nozzle was..how did you retrieve the rest of the nozzle?.
@howtolife5705
@howtolife5705 5 месяцев назад
Please come to Brighton UK and do this on my van!! 🙏
@GORANRELJANOVIC
@GORANRELJANOVIC Месяц назад
Fantastic job. Coul you be so nice to tel me which drill and thread taps are you using. Thnx very much in advance.
@tinker-time
@tinker-time 5 месяцев назад
yer good job that hats off 👍👍👍👍👍👍
@zambotv8150
@zambotv8150 Год назад
Amazing
@MrMay141971
@MrMay141971 2 года назад
You have done such a great job, but the design of these fuel injectors is really bad and stupid
@user-ki5vq1mh3m
@user-ki5vq1mh3m 9 месяцев назад
Thanks allot sir
@cyborg9718
@cyborg9718 2 года назад
Good evening can you tell me which drill bit you use to smash the injector at 16:40
@Shmbler
@Shmbler 2 года назад
Funny. Two weeks ago I noticed that water is dripping on the head of our Trafic. Looks like I have to remove that panel, too ;-)
@brianschneider9067
@brianschneider9067 9 дней назад
How did you extract the remaining portion of the injector nozzle? Clearly a portion of the nozzle was not extracted. How was it facilitated?
@arkaprestige8051
@arkaprestige8051 Год назад
Need help, My Chevy Cruze petrol, just having rough idle and a lot of white smoke, the mechanic already change the Piston ring, cylinder gasket, but the problem still there, help me diagnose the problem, is it air flow sensor, or bad injector, or bad coil, or bad head gasket? Thanksss
@ezel565
@ezel565 2 года назад
How much complete puller please uk
@kat0197
@kat0197 10 месяцев назад
Where i Can buy this hydraulic piston??
@boomshakalaka2275
@boomshakalaka2275 3 года назад
Great job, did the end of the tip on the 4th injector stayed inside the head? Did I miss anything?
@OGSMechanics
@OGSMechanics 3 года назад
The injector nozzle was removed before we pull the lower injector body.
@glennbartlett416
@glennbartlett416 Месяц назад
At 17:48 the bottom part of that tip is missing! Where is it? Did we even see that the engine run ok?
@hot-shotlabel3212
@hot-shotlabel3212 Год назад
Where to buy the tool?
@yensabi
@yensabi Месяц назад
Had my vivaro injectors and glow plugs done by this company a few years ago , not cheap but they did a great job , it’s a really badly designed engine and scuttle to allow this to happen.... 👍
@moffatt43
@moffatt43 Год назад
Good work but you could help yourself out quite a bit with this particular model by where the water gathers and goes into the injector seats if you squirt loads of WD40 in there for a few days before the vehicle gets into the Garage. The injectors I don’t normally tend to have a problem with,it’s the Glow plugs but they can be assisted in coming out with the same principle of explaining to the customer that they can help by a few weeks before the Job if they can squirt just a little bit of WD40 in the glow plug seats. I also explain to customers the importance of keeping leaf’s and debris out of the location below the windscreen and therefore keeping all the drains clear. The amount of problems that customers have which could be simply avoided if they did some general maintenance on their vehicles is incredible….!. Nowadays with these panoramic sunroofs and people who are not aware that they need to :- 1: Keep the Sunroof rails and drains clear 2: They need to get ( and ask specifically ) for a sunroof service 3: Fuel Filters do not replace themselves ?!!.
@xxwookey
@xxwookey 7 месяцев назад
plusgas is a much better penetrating release agent than WD40.
@HamzaHamza-dn2nt
@HamzaHamza-dn2nt Год назад
How we can this same thing
@robfromga2
@robfromga2 Год назад
What took is that?
@sailingikis
@sailingikis 6 месяцев назад
How much does a work like this costs for a Ducato?
@Stu-SB
@Stu-SB 2 года назад
Fantastic vid, what a piss poor design by the manufacturer, little to no real forethought of water dispersion off the scuttle panel, the engineers should have their arses kicked for creating this problem... EDIT: I've a 2017 Mk3 Trafic and checked each sides drain last night, flowing freely thankfully !
@martinj9251
@martinj9251 Год назад
How much for this service,?
@almacsutka4571
@almacsutka4571 11 месяцев назад
And the engine can run or can't?
@frederickkwek3772
@frederickkwek3772 2 года назад
I’m just wondering why penetrating fluid is not used to help with the extraction?
@Hissing-Syd
@Hissing-Syd Год назад
Apparently even with penetrating fluid they can still be a real pain to extract, I've heard of all sorts of stuff used, one chap recommended using vinegar to break the corrosion between the head and injectors.
@garybrown5500
@garybrown5500 Год назад
The injector clearance between the head is so tight with corrosion penetrating fluid would take months to penetrate where it is needed, Much like seized nuts on bolts very rarely do you see the ingress of fluid when the parts are dismantled.
@martinj9251
@martinj9251 Год назад
Because clearly it was not needed!!
@djgomaz1
@djgomaz1 2 года назад
Fantastic 👍
@ym-imyloi981
@ym-imyloi981 3 года назад
How much would this roughly cost for all 4?
@mosquitonable
@mosquitonable Год назад
About 2000 US dollars for 4 brand new injectors. Cheaper if used ones
@piciu256
@piciu256 Год назад
Could applying anaerobic sealant at the sleeve prevent this issue altogether?
@DG-EditsMedia
@DG-EditsMedia 6 месяцев назад
Probably
@troubledtinkerer
@troubledtinkerer Год назад
Do you cut all the seats or just the one that was drilled?
@FreddysHamster
@FreddysHamster 7 месяцев назад
Watch the video?
@niallenglish3777
@niallenglish3777 Год назад
gr8 vid and v informative, thanks 4 sharing. This is a job and possible probs I've got coming up now shortly, so have a few Q, 1, after you widened and drilled out the sleeve in order to remove the broken injectoe/nozzle, How'd you sort the sleeve for th next injector to fit into as surely the hole is bigger now, or has a different thread on it. How's that work with th new injector designed for something different? 2, do you always have to enter a new code into system when changing fuel injectors? and if so, How's this done? I don't have a top of th range OBD tool, am planning to upgrade th one I've got, but what capabilities must it have? can we not just order injectors with th same code to suit?
@nate123123we
@nate123123we Год назад
1. You replace the sleeve with the injector. 2. Yes, you do need to put the new calibration code in, its done with a OBD tool.
@AfzalKhan-vh3ny
@AfzalKhan-vh3ny Год назад
Can you please add link to buy hydraulic Injector puller
@shamstar2k
@shamstar2k Год назад
looks like one they made
@ferrarigto599
@ferrarigto599 Год назад
I use silicone to put on the injector on all lenth...
@mosquitonable
@mosquitonable Год назад
Is it safe to use WD40 to loosen rusted injectors?
@xxwookey
@xxwookey 7 месяцев назад
Yes, but plusgas will work much better.
@howtolife5705
@howtolife5705 5 месяцев назад
Why worry about changing the injectors when it's clearly an electrical problem that can be sorted by cleaning & sealing the contacts & wiring, and fixing the leaking scuttle? The electrical part of the injector is at the top and easily accessed without removal.
@glenfordstobbs1325
@glenfordstobbs1325 2 года назад
hey where can i get that tool to buy
@RayBrennan
@RayBrennan 2 года назад
This guy didn't curse once! 😂😂
@yasintokmak251
@yasintokmak251 2 года назад
how much km ?
@jesshowe4591
@jesshowe4591 2 года назад
How do you get all the bits of rubbish that fall through into the piston out
@garybrown5500
@garybrown5500 Год назад
Compressed air.
@fredfly001
@fredfly001 3 года назад
WHY oh Why are you doing this dry, surly it would be better to let the area soak in penatrating oil to help break the dry corrosion, then it may not have snapped ! Not really the way to do it - DRY
@frederickkwek3772
@frederickkwek3772 2 года назад
I totally agree too....why CRC or WD40 is not used before hand?
@everythingeverywhereanyone
@everythingeverywhereanyone 2 года назад
I thought same thing , would of definitely helped.
@tugrulbey3095
@tugrulbey3095 2 года назад
No it does not help. Not even a bit.
@thatdaftscottishcarguy
@thatdaftscottishcarguy Год назад
the injectors were corroded all the way down, nothing would break that down and would just be a waste of time
@JJ-jc8yv
@JJ-jc8yv Год назад
@@thatdaftscottishcarguy what about freezing injectors and waiting 5 minutes before removal?
@bboytyby
@bboytyby Год назад
Why no wd40?
@clifjonejontilano3578
@clifjonejontilano3578 Год назад
Looks easy when i was watching, but im sure its totally different when im the one doing it😂😂
@leekirtley7234
@leekirtley7234 2 месяца назад
There are lots of stories of injector removal horror stories and tons of vans for sale with injector problems. Do you think people go at these injector jobs with the wrong gear and no idea?😮😮😮
@stormeagle28
@stormeagle28 2 года назад
LOL!! Just wait another year and the injectors will cleanly rust out of the engine.
@stevenbean9706
@stevenbean9706 Год назад
mine broke right in half
@karlavelo2482
@karlavelo2482 Год назад
This makes me wonder why Renault invests in Formula 1 when they can't manage to avoid such engine design flaws ...
@lancepage4840
@lancepage4840 Год назад
No new pipes !!!
@howtolife5705
@howtolife5705 5 месяцев назад
Why pull them out raw, no pretreatment with penetrating fluid? That's brutal. That last one snapping could've been avoided!
@garrysouthern1439
@garrysouthern1439 4 месяца назад
where abouts are you
@tonyclack5901
@tonyclack5901 Год назад
Thats not seized. When the bolts snap off of the injector clamp then you know the injectors will be properly seized.
@themagpie_1
@themagpie_1 5 дней назад
that is the Nissan engine. I have the Renault engine F9Q in my Vivaro. such a better engine to work on. i`ll never sell my 2005.
@peternewman3487
@peternewman3487 9 месяцев назад
There is no excuse for water ingress like that whatsoever.
@howtolife5705
@howtolife5705 5 месяцев назад
Tell that to Renault/Vauxhall. They should be in court for this
@chrismills9346
@chrismills9346 2 года назад
Load crap engines chain snap on them too stay well away from them
@user-tn1hk6zm2f
@user-tn1hk6zm2f 2 месяца назад
All this new designed stuff is junk.
@barongreenbackthe2nd418
@barongreenbackthe2nd418 Год назад
I need my 2.5 vivaro injectors removing,I live in Devon please help me.
@lordvonzipstor5304
@lordvonzipstor5304 Год назад
Hey mate, I have used basically the same system however it is fully mechanical, the rod spins with a 24mm spanner on my 2.0 dci Trafic after a 24h bath in super lubricant and the thread literrally came out, have a look here photos.app.goo.gl/KiA6CQoakSS1ZRv88 Unsure if I should try the same on the others or if I just should forget about this operation, continuing to drive the vehicle on 3 legs. Let me know, cheers mate.
Далее
My WORST Birthday Ever..
01:00
Просмотров 22 млн
ПАША ТЕХНИК. Прощай, Легенда #3
42:40
OM606 STUCK Glow Plugs Re-Visited How To get them out.
24:17
Leaking Injector: How to Replace to Avoid BLACK DEATH
17:26
HOW TO REMOVE STUCK DIESEL INJECTORS *EASY WAY*
8:31
Просмотров 150 тыс.
opel vivaro injector removal
1:59
Просмотров 198 тыс.
Amazing Diesel Motorcycle 🔥
0:19
Просмотров 35 млн