NEW Makita 18v Inflator VS OLD Makita 18v Inflator | The new one is a LOT Better... or is it?

Подписаться 68 тыс.

Просмотров 172 тыс.

50% 1

Old vs new in this one with Makita 18v inflators. Check out the links below for more info.
Grab one from Home Depot homedepot.sjv.io/6bBg1E
Patreon / toolsandstuff
My Other Channel / buildsstuff
NEW DMP181
NZ shop.handyhardware.co.nz/maki...
US amzn.to/3DwbQc0
UK amzn.to/30dgUEE
OLD DMP180
NZ shop.handyhardware.co.nz/sear...
US amzn.to/3DwbQc0
UK amzn.to/30dgUEE
XGT MP001G
Worldwide ebay.us/5fh5ZD
UK amzn.to/3pxMUMg
If this description contains links to Amazon or Ebay, as an Amazon Associate and EPN Associate I may earn from qualifying purchases. This doesn't cost you a thing! But it means I can make more videos for you.
I couldn't find the trigger lock device... sorry
HELP ME MAKE VIDEOS
www.paypal.com/donate/?cmd=_s...
►►►Handy Hardware www.handywarehouse.co.nz/ 1/79 Wairau Rd Auckland
►►Get some 40v tools in the UK & Europe amzn.to/3306Htf
►Makita 40v finally available in the US! amzn.to/3tszyAP
More Makita XGT 40v Videos
40v MITRE SAW • Makita 40v 216mm Mitre...
40V BRAD NAILER • Makita 40v Brad Nailer...
40v STICK VAC • Makita 40v Stick Vac V...
40v 125mm CIRCULAR SAW • Makita 40v 125mm Circu...
40V 165mm CIRCULAR SAW • Makita 40v 165mm Circu...
40V 185mm CIRCULAR SAW • Makita 40v Circular Sa...
40V 260mm REAR HANDLE CIRCULAR SAW • Makita 40v 260mm Circu...
40V ALL DRILLS COMPARED • Makita 40v Drill Revie...
40V IMPACT WRENCH • Makita 40v Impact Wren...
40V IMPACT DRIVER • Makita 40v Impact Driv...
40V ROTARY HAMMER DRILL • Makita 40v Rotary Hamm...
40V RECIPROCATING SAW (SAWZALL) • Makita 40v Reciprocati...
40V COMBI DRILL (HAMMER DRILL) • Makita 40v Hammer Dril...
40V GRINDER REVIEW • Makita 40v grinder Vs ...
40V CHARGER & BATTERIES • Makita 40v Batteries a...
40V CIRCULAR SAW • Makita 40v Circular Sa...
40V DRILL CLUTCH SETTINGS • Makita 40v Hammer Dril...
40V RADIO • Makita XGT 40v Radio |...
PURPLE MAKITA IMPACT DRIVERS (& OTHER COLOURS)
NEW 18v Makita TD172D in all available colours ebay.us/HADzgU
18v Makita TD171D in all available colours ebay.us/b7erGy
40v Makita TD001G in all available colours ebay.us/kzI7Uq
MORE VIDS
My Top 5 18v Makita • My TOP 5 Makita 18v Co...
My Top 5 36v (18v x2) Makita • My TOP 5 Makita 36v Co...
Homemade Hot Tub • How to Build a Hot Tub...
MY AMAZON STORE www.amazon.com/shop/toolsstuff
ToolsContactNZ@Gmail.com
If this description contains links to Amazon, as an Amazon Associate I may earn from qualifying purchases. This doesn't cost you a thing! But it means I can make more videos for you.
Check out my other videos for reviews of Makita, Hilti, DeWalt, Bosch, Hitachi, Ryobi and more... As well as build projects and the odd random thing.
#MakitaInflator
#ToolsandStuff
#BuildsandStuff
#KiwiToolReviews
New Zealand

Хобби

Опубликовано:

22 май 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 269

@ToolsAndStuffOFFICIAL 2 года назад

NEW Makita Tools Coming Soon... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V2T7axr4KDE.html

@shanewright4317 2 года назад

Hey! Would the new one have pumped the rugby ball up on the regular setting if its limit wasn’t set to 70kpa? Meaning have it set much higher? Thanks for your videos man!

@RogerThat1945 2 года назад

Price mention is handy. I just checked, and the newer one (181 vs 180) is 75% higher price where I live (approx. USD equivalent $80 vs $140 our amazon); might have to flip a coin to decide (as lower price & weight/smaller storage is also good).

@bcgunner9324 Год назад

Thanks for this video. I got the smaller one from my local home depot to bring my truck tires up from sand pressure, back to street-safe (12 to 25) and it was just too slow for the task. Seeing how the 181 is almost twice as fast, I think it will do nicely. I love having one battery system for all my tools... Makita is the best.

@LilasTools 2 года назад

Excellent review as always, the new 181 is a hug improvement still a shame no trigger lock though. I don’t own a inflator yet, so If I see the old model on clearance I’ll probably pick it up! Cheers

@Aladinscave 2 года назад

Got the 40v a few days ago and happy to say so far its been really good it inflates motor cycle tyres really quickly for a battery powered pump and the size isn’t really an issue considering it does the job quickly 💪🏻🏁

@adamhindle9215 5 месяцев назад

a perfect review. All the key info (except noise data), and entertaining to boot. I have the 180 and it's okay but weedy and quite loud, and the trigger thing is a pain, obviously. I use the ziptie mod too.

@timvangool291 2 года назад

I prefer the quick clip on method. I use it on my racebike to fill my tires. Best Makita tool i own and also the cheapest in the toolbox :D

@pjfaust254 2 года назад

Fantastic comparison! I would’ve liked to see it with a very large truck tire but this video helped me out. My 180 will do a truck tire from 17 to 35 psi in about 7 minutes. I’m thinking the 181 will be around 4. Thanks again for the comparison

@chrisstafford5660 Год назад

What a great comprehensive review , well done chief from Ireland .

@ToolsAndStuffOFFICIAL Год назад

Thank you kindly

@urntwrthyZ 2 года назад

Very thorough, nice work. I much prefer the clamp on style.

@LEXPIX 2 года назад

Nice demo. Glad I waited for the 181 version.

@andygilbert1877 2 года назад

I have the 12v version which is great for small car tires and bikes. A nice compact unit. Interesting that the old 18v one is little better than the 12v one though, glad I didn’t wait for that to come out! The new one is usefully more powerful and I’d probably buy that for workshop use, but no need now as I’m retired. :) If the lack of a trigger lock bothers you just set up and trim a zip tie and leave it on. Though I did that 2 years ago and have never used it! I don’t think I’d like the screw on valve connector but if it bothered me I’d change it to quick connect. (Or maybe combined Presta/Schrader)

@Gedsterboy 11 месяцев назад

Great comparison review. That helped alot!

@winchesternathan Год назад

Thank you for the review. That helped. I have already "standardized" on the Makita batteries and have 2 Makita drills, a hedge trimmer, a 36V blower (that uses 2 18V batteries at a time) and a string weed trimmer, so I was already leaning towards a Makita air compressor, but this sealed it. Gonna purchase the Makita DMP181ZX 18V LXT. Sorry about your rugby ball!

@christopherenoch4230 2 года назад

Loved the opening... Fly fishing NZ is on my bucket list! Dang COVID... Lord willing, I'll make it there someday.

@mickgleeson4284 2 года назад

Great review and helped with my decision. Well done and quality video. Cheers from across the ditch.

@ToolsAndStuffOFFICIAL 2 года назад

Cheers

@patmat. 2 года назад

Great review as usual, thank you!

@ToolsAndStuffOFFICIAL 2 года назад

Cheers

@nicksgarage2 2 года назад

Can't wait to get the new one. Not available at Amazon for me in the US yet. I use my LXT one all the time and I'll just leave in my truck tool box. The trigger thing is not a big deal. I just keep a velcro strap on mine. I thought about getting the XGT version but it doesn't seem that there is that much advantage and I don't have any XGT tools yet. And yes, I'll appreciate the screw on connection as I have a lot of tube tires I'm inflating and it's hard to get the clamp on one on some of them.

@timothyroper1897 Год назад

MATE Thankyou for ALL your Makita revews. As a Makita fan I have valued your opinions on the tools/ battries. I have choen with insight when gettting my kit. Your videos are always interesting-thanks again from your UK FAN (my wife needs abit more convincing about how I get carried away with my purchases though)😁

@ToolsAndStuffOFFICIAL Год назад

P.S. 20% of my watchers are "UK Fans"

@Ya-never-know 2 года назад

It’s cool but I’ll probably stick with the original as it fits perfectly under my back truck seat. Side note, 9,000 views and 285 thumbs up so far? Come on, we all know this man is putting out some of the best tool reviews. Perfect blend of real world info and a unique blend of comedy. Let’s get him some more recognition, it’s mutually beneficial.

@ToolsAndStuffOFFICIAL 2 года назад

Cheers man

@Hours-zi9js 2 года назад

Great review. I bought the xgt a couple of weeks ago. Can’t wait for it to arrive

@ToolsAndStuffOFFICIAL 2 года назад

The XGT is very similar to the new LXT, just a little bit quicker. Review soon.

@Hours-zi9js 2 года назад

Honestly. For what it’ll do for me 35-55 psi… you’re probably right. Maybe the difference would be more noticeable with suv/trucks that have 90 psi tires

@cb6171 2 года назад

Thanks mate, just ordered one for here in the UK

@ToolsAndStuffOFFICIAL 2 года назад

Cool 👍

@MM-qv5lf 6 месяцев назад

It's crazy how fast they inflate the car tire from zero, wow. And that was fun watching the ball explode. 😂

@snooka2484 Год назад

This is a great mobile tool. I love it. Perfect for road trips and pool floats/balls. I still fire up the compressor if I'm in my garage for the vehicles...it's just way faster.

@beeftec5862 2 года назад

I use a velcro strap to hold on the switch on the old model. Always check the set pressure before doing this though!

@swilson317 Год назад

"Make sure you lube up your needle before you jam it in your ball." LOL! Good advice! My take on the different ends is that the screw-on is easier for car tires...especially if there is tight clearance on a rim. I would prefer the older model with the quick connect. But I would probably use it more for my road bikes than car tires. I wished they had a version of the clamp-on end specifically for presta valves. Great comparison! Thanks!

@vitaliybulochnikov9264 10 месяцев назад

Thank you, good review. Can this pump be used on SUP’s?

@ampex189 Год назад

Thank you! I was looking at these at a local store and didn't know the difference. I'll definitely be going with the 181, faster and has the screw on connector.

@mattkaplan1316 2 года назад

I like the screw on better , you don’t have to worry about it slipping or not holding properly works the same every time

@cleftoftherock6797 2 года назад

Very good. I’m sold. The 181 is $62US dollars more that the 180 but definitely seems worth it. Thanks.

@felippebarretto5514 Год назад

Great video, thank you

@shanew7361 2 года назад

Great video

@Ist_Geheim 2 года назад

I got my DMP181 a few days ago. What I don't understand is that in the price-class of more than 100 EUR they didn't manage to put the LED straight on. It shines about 10 degrees to the right, at least on the one that I bought. Of course the tool and it's light is absolutely usable, but for that price I would like to get more perfection and/or quality control. The solution that the DMP181 has - to srew it onto the car-velves - is not bad, especially when I remember how many seals on "90°-squeeze-solutions" I have seen broken. However, I immediately upgraded to a "screw-on quick-adapter" (I don't know how they're called in english). A penny-tool if Makita bought them in bulk, I don't understand why they deliver it with the tool (in this price-class!).

@markthespark6240 2 года назад

I'll stick to the DMP180Z - The angled valve connector is perfect for kids motorbikes and tight places.

@maff5535 2 года назад

I wish id know the bigger version was coming out before I bought the first 18v inflator. I pressure test heating systems with mine often and I think it struggles.

@sixtyfiveford 2 года назад

Still in my opinion a little bit small for filling anything other than a small car tire. I run a cheap12-volt clamp on car battery one that'll put out 42 LPM/1.47 CFM (Makita dmp181z 23LPM/.81CFM) and I feel like that is slow sometimes.

@justinvanaulen2478 2 года назад

Nice job. Can’t wait to see the 40v XGT version. These are hard to come by in the USA at the moment. As others have mentioned, a tear down would be great! You have the the best channel(s) on YT for “real world” tool reviews. Keep up the great work, your making a difference for those of us who rely on trustworthy reviews for buying decisions.

@ToolsAndStuffOFFICIAL 2 года назад

Thanks man, appreciate it. You won't have to wait long for the xgt review...

@gwailo2010 2 года назад

Thank you Sir.

@holton345 7 месяцев назад

I loved my old 12V Makita but sold it to a friend when I got this new one. It is a LOT better. BUT WHY NO TRIGGER LOCK, MAKITA?

@Jackofalltrdes Год назад

Awesome video thank you

@ToolsAndStuffOFFICIAL Год назад

No problem.

@vinhhoang5397 Год назад

Please let me know where to buy the quick connect clamp. Is there any part number for it? THANK YOU!

@ML-sj8ti 2 года назад

Is a tear down in the planning? I would love to see the internal differences and what they’ve need all that extra space for!

@ToolsAndStuffOFFICIAL 2 года назад

I hadn't planned to... but you never know...

@HVACGUY 2 года назад

Much prefer the quick clamp. In some instances it’s difficult to add air with a straight hose: for example reaching behind a hubcap.

@Ist_Geheim 2 года назад

You can buy an adapter and srew it on. If the seal in adapter breaks from squeezing, you could buy a new adapter and your tool itself is still ok. So I prefer the DMP181 over the DMP180.

@kevinmunz 2 года назад

Really wish they would add a powerful cooling fan to these small inflators. They get so hot and don't use much power, so I don't see any downside.

@ralphcantrell3214 2 месяца назад

The lack of a locking trigger is tragic. I guess I'd just keep a foot of parachute cord on it to tie up the trigger when needed.

@photogra4 Год назад

Thank you for this video! You've made my decision much easier now. BTW, Thats's a good looking Makita charger. I can't seem to find one here in PA (USA) or on a quick google search. Can you tell me what the model number is please? Thanks again

@jamilal-yaqubi1986 2 года назад

Another great video. The simplest thing is that Makita should just sell an adapter that you screw on yo the end that lets you clamp to a valve the way the 180 does. Then you have the best of both worlds. Like you said, a lock on the button is missing, but what I would also like to see is a low pressure, high volume mode for blowing up paddle pools and the like.

@1d1hamby 2 года назад

I believe he tried to demonstrate that with the 181 on the rugby ball, but there was too much pressure.

@jamilal-yaqubi1986 2 года назад

@@1d1hamby no, this inflator does not have a low pressure mode. It is the kind of inflator used for air mattresses and paddle pools. I keep a cheap one in the same case as my DMP180, so I have them handy in the same place.

@johnlucier5654 Год назад

Wonder if the handheld blower would work for that with a reducer on the end.

@MM-qv5lf 6 месяцев назад

Do you have to let go of the trigger when you reach the set pressure or do you keep the trigger squeezed until the machine stops by itself? Assuming it stops by itself right?

@chriswesney 2 года назад

The fact that makita didn't make a trigger hold is insane! Dewalt and Milwaukee both have the feature that let you set them and walk away.

@Aladinscave 2 года назад

Didn’t find this to be a issue for me 🤷🏻‍♂️ it’s a safety thing, if you are planning on inflating a giant wheel witch this is not designed for then it will be annoying sitting there for a long time, it inflated my motorcycle wheel in a very reasonable time.

@forrestn4988 2 года назад

@@Aladinscave Unnecessary "safety thing".... you set the psi on the control screen and it shuts off even if you are holding trigger.. what a wast of time ....

@LemonySnicket-EUC 2 года назад

Stop crying . it's simple to make your own. it's a 10min maximum on 5 off though so it is a safety issue to not have one. . Just deal with it.

@LemonySnicket-EUC 2 года назад

@@Aladinscave 💯%

@deeeeeeps Год назад

I have to hold the inflator when I use my big compressor ..what is the difference.

@mediocreman2 2 года назад

Wait, what is the point of the auto shutoff if you have to hold it? The entire point of auto shutoff is to increase safety and convenience. It actually can be dangerous to sit next to the tire while it's inflating. Even my much cheaper Ryobi has this feature.

@ryanassenberg3138 2 года назад

I prefer the new screw type attachment better, prevents damage if tyre it flat and u are pushing the valve back.

@johnlucier5654 2 года назад

Saw a hack where you can drill a small hole in the handle through the trigger and insert the ball needle to hold it down.

@RealJohnnyDingo Год назад

brilliant, even more so because I don't otherwise use the ball needle 🏀 💉 🏀

@ryanpkeeton 9 дней назад

If you hold the trigger on and it gets to pressure and shuts off does it start pumping again if the pressure drops?

@maximusprimus827 2 года назад

Had no choice but to buy the DMP since I am already invested in the Makita platform. It sucks that there is no trigger lock 🤦‍♂️

@oraniyan 2 года назад

I use DMP180 mostly to inflate mtb tires. The valve connector and the auxiliary adapters are like straight from 1981, not 2021. I really wish it had a valve connector that can handle both Presta and Schrader valves. Why not, there are floor pumps and pressure gauges with such connectors. And for my preference it should be quick connect type. Tyre pressure check is my daily routine (especially tubeless mtb tires often lose pressure). It is too slow and cumbersome with the connector that accompanies DMP180 for Presta valves. But I think all in all it would be the best if the hose had a connector onto which you can screw any kind of end, and then of course Makita would provide a sufficient variety of different connectors. - I like the improved display and deflate button on the newer model. I would like to be able to calibrate the pressure gauge. I have three gauges that give same readings between them. Makita's values differ slightly, by 1-2 PSI.

@hereticus1994 2 года назад

I’ve got the 181, and I’ve got it set up with a prestacycle big head inflator for my mtb and roadie and quick clip right angle schrader head for the bmx. Works like a charm and saves so much time topping off the many many bikes in our house. From the reviews the 181 is a bit faster too apparently.

@scottspropertyservices6877 2 года назад

@@hereticus1994 never seen or heard of the prestacycle range before. Just googled it. It’s a game changer for these inflators, thank you very much!!!

@wealthfinder192 Год назад

The screw on valve seems a better fit although would be annoying trying to get it on the thread right to start. But it would be more secure than just the push on valve. IMO. You should do a test between the big bertha with the 5ah battery vs a 3ah or/and a 6ah battery. I know it can make a big difference with the drill so would expect it to make a difference with this. Your time would be a lot slower with the 3ah and faster with the 6ah I think. Also, I have a Ranger with the big all terrains on it. Would like to see how it goes with that.

@ToolsAndStuffOFFICIAL Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-VOKpED2Jrok.html

@karenstein8261 2 года назад

Lovely - and I just bought the 180 for my car. Smaller is better when you have limited cargo space. I’m no about to time myself though. What’s the time when you need to, say, get a tire up to 32PSI after it leaks down to 20PSI? Just what I’d need to get my car to a shop ... Battery voltage? Keep it the same as your impact wrench and you need carry but one battery.

@hobbes3 6 месяцев назад

That's exactly what I did. Got my 18V 1/2" impact wrench with a 21mm deep socket, a Harbor Freight torque adapter, a 15" breaker bar, and this 18V inflator and I'm good to go for all tire changes lol.

@daz7038 4 месяца назад

DMP181Z I am absolutely baffled by the design of this tyre inflator. 1. You set the target limit, but then have to bend down to hold in the trigger to make the pump work. I bought it to save my back and it doesn’t do that. 2. Why is there no auto shut off? What is the point setting the target pressure? The pump will also continue pumping if you hold the button in past the target pressure. 3. There is a bracket for a valve I’ll never use hanging on the end of the inflator tube which makes it very awkward to attach. Why isn’t it stored elsewhere? 4. The tube has a straight valve connector that loses pressure as you unscrew it and is also nigh on impossible to get it on to a motorcycle front wheel valve. Valve needs to be right angled and quick release.

@cg.4836 2 года назад

I’m at a loss as to why makita doesn’t make a proper LXT or XGT cordless air compressor. Seems like they could just strap one or two of these to a 5 or 10 litre tank. And call it a day.

@PistonHonda87 2 года назад

Would like to see a new makita x2 lxt miter saw with a cast shadow and better miter gauge.

@RayW808 2 года назад

quick release much preferred

@calumward1192 Год назад

People really be mad about it having no trigger lock 😆

@derekrugby 2 года назад

Where do you get that battery tester thing?

@ccbowers 2 года назад

I usually prefer to use a quick connect, but would rather have a threaded connection attached to the tool, and can add on a screw on quick connect. That way it is replaceable if/when it stops working well.

@jeremybaity7002 Год назад

Do you have a part number for that charger you are using at 9:11

@jacobhendrickson8935 6 месяцев назад

Why did you scrap that van, I’d so love to have one of those.

@magiic1701 2 года назад

Hi Great video - what is the model number of your LCD Makita battery charger you are using? is running 240v or 110v?

@ToolsAndStuffOFFICIAL 2 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uumwieLu8CE.html

@wesseallik9991 7 месяцев назад

DMP181Z is better then DMP180Z but the price difference is almost 2X times (115 euros vs. 60 euros). Same time, they are both home use only devices - for random flat ball or tire and that's it. You're not going to use them at air tools at the worksite, or in carshop etc. The thing, that 181 is a little bit faster, don't really matter in this case ... you going to use that anyway few times a year max and if you need a device for everyday use, you're going to get real tool, with tank and decent pump.

@NVRRVN 2 года назад

The pressure gauge in the 180 is very in accurate.

@Derek-tk4wf 2 года назад

Whats that Makita battery diagnostic device called at the 9:10 mark? I looked on makitas site and cant find anything close to that.

@ToolsAndStuffOFFICIAL 2 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uumwieLu8CE.html

@Hours-zi9js 2 года назад

Any videos on Makita corded or cordless vacuums? Don’t know if I should get the 4 or 11gallon… or wait on a 40/80v all together

@ToolsAndStuffOFFICIAL 2 года назад

Only what I talked about in this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V2T7axr4KDE.html There is also another, more basic one, without AWS and only dry.

@maff5535 2 года назад

For pressure testing heating systems I bought the smaller 18v before there was any news of the bigger one. Its hard not to feel scammed because I would've certainly bought the bigger one. The smaller one kind of struggles with bigger systems.

@joeljandoc750 Год назад

Do you think the 18v is good for pressure testing gas line?

@chrisE815 Год назад

Hmm what systems are you testing? Isn't nitrogen usually used for that sort of thing?

@maff5535 Год назад

I have just used Air to pressure test heating systems before filling them

@joeljandoc750 Год назад

I usually pressure test main gas line to my manifold and all the appliances. It's usually 2" hard pipe. Do you think the older 18v will do the job? I hate lugging around an actual air compressor

@sanraki 2 года назад

I have the older one for mountain bike tires and it kinda sucks. Like with your empty balls I've notices that it can't really deal with starting and measuring low pressures like 5 psi or ~0,3 bar and up. I have to over pressure the tire and then lower it with a pressure gauge which kinda defeats its purpose. For a car tire it's fine.

@trentkammerer8639 2 года назад

What is that Makita battery device on the video that shows charge count, voltage, etc? Do you have a part number?

@ToolsAndStuffOFFICIAL 2 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uumwieLu8CE.html

@darrylbuckett5380 2 года назад

As far as the Schrader valve goes I don't like either as neither will fit onto my wheelbarrows or mulcher wheels, so I have to take the wheels off and trundle up to the servo and fill up there as their schrader valve is offset and double headed so it can come back on itself. This to me is a major flaw that would be simple for Makita to fix, but it pumps up pool toys etc easily. So come on Makita Fix it. Cheers

@gezagyorfi 2 года назад

Is it just me who can`t find the size of the car tyre in the video? I`ve got a (4x4 dual pump) 12V compressor at home with different tyre size inflation times and would like to compare it to the new Makita.

@pollyaloy Год назад

I found the 180 to be very accurate

@djjinerson 2 года назад

Never had a screw down inflator, but I hate the click down style for sure. I want to get this for that reason alone

@T5VeeDubVan Год назад

What battery charger is that one?

@tomallen6073 Год назад

I have the smaller version and like the more compact size. Will probably never use it to fill a large tire from zero, just top them off. I like to keep mine in my truck. It would like to see which one is more efficient, how much can you get from one battery?

@visionsdb6695 9 месяцев назад

How long for a top off?

@andrzejpolak1313 2 года назад

I am a huge fan of your tests from Poland. I want to buy a cordless hammer drill. I am thinking of choosing Makita HR004gz or DeWalt dch333. Which you would recommend to me. Unless you make such a comparison? You can take Hikoki, Hilti or some other companies to the list.

@ToolsAndStuffOFFICIAL 2 года назад

The 333 is the most common here. But if you are starting platforms from scratch then I would go for the 004

@andrzejpolak1313 2 года назад

Thank you for the answer and advice

@colinwilson8747 2 года назад

Screw on version is not always possible to connect on some motorbike tires. So while the screw on is great can't always use it.

@salforeverify 2 года назад

I prefer the screw lock on the dmp181z over the clip style. The hose freely rotates so its easier to attach/screw. Hate that you have to hold the trigger down.

@neverputon5878 Месяц назад

I have switched to milwaukee tool sets at work and got the inflator its really good . I still use all my makita at home really like my makita tools. I bought the 181 not going to mess with little ones no comparison milwaukee was better in so many ways. First time disappointed with makita besides the battery issue that was the reason to switch at work. I wish I could return 181 I really don't like it.

@theperfectpaintertoolreview 2 года назад

Where can I get that Makita battery checker thing that looks like a charger with a screen? I'm in the usa

@ToolsAndStuffOFFICIAL 2 года назад

Have a look in the description of this review I did on it. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uumwieLu8CE.html

@claudesz 2 года назад

Just about to buy the smaller model so glad I didn’t in saying that who knows when it’ll come to Australia still waiting on the sander that you reviewed there’s still none in the country supposably

@ToolsAndStuffOFFICIAL 2 года назад

The sander has been out here, along with the AWS version for a few weeks.

@claudesz 2 года назад

@@ToolsAndStuffOFFICIAL Our main tool supplies here which are total tools and Sydney tools still don’t know when they’re getting them😭

@ToolsAndStuffOFFICIAL 2 года назад

Buy one from NZ

@photogra4 Год назад

OK, amending my last question... is it only a voltage/charge Guage with the readouts and NOT a charger? Or does it charge as well? (*This may be why I can't seem to find it via my searches)

@ToolsAndStuffOFFICIAL Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-uumwieLu8CE.html

@delchevdaniel 2 года назад

Can you please share a link for the battery checker?

@ToolsAndStuffOFFICIAL 2 года назад

ebay.us/H7RlYu

@michaelcostello6991 Год назад

In would like to see how the British attachment works ?

@mikkomakela3234 2 года назад

Filling car tires with DMP181 is not as easy as with the DMP180. Why they had to change the head from tratitional...

@strummer6642 Год назад

Great video comparison, I'd have thought blowing up a rugby ball in New Zealand would be considered sacriligious!

@strummer6642 Год назад

I ended up getting the 18 volt brushless model, very happy and the equivalent or faster than a typical UK garage forecourt self service system if that helps anyone

@liiich6175 2 года назад

I wonder if any of these infiltrators could seat the tyre to the rim on a tubeless MTB

@ToolsAndStuffOFFICIAL 2 года назад

I'm guessing that was an auto correct error... And I doubt it.

@elbling9322 2 года назад

Where did you get that makita battery health thingy?

@ToolsAndStuffOFFICIAL 2 года назад

ebay.us/amSrSI

@markhedquist9597 2 года назад

The three of them look like a family of elephants. To me... I have the 12v one. Carry it in my little Datsun truck. Works great. And, no, my truck is not "inside" my household. Am I in violation of something? The new one seems to be a beast. Am I wrong in thinking they have an XGT one out also? Thanks for the video. And, as always, cheers!

@ToolsAndStuffOFFICIAL 2 года назад

Next week...

@adilsyed7838 Год назад

G'day mate. Thanks for the video, I ended up buying the DMP 181 & have a question please, does the autostop kicks in precisely at the air pressure selected? On mine it kicks in 3Psi over the pre-selected air pressure everytime, so I pre-select 35Psi & the autostop kicks in at 38Psi. Is that normal because if it is not I will go get a replacement. Thank you.

@RYN988 Год назад

mine does the same thing, it adds 2-3 PSIs

@adilsyed7838 Год назад

@@RYN988 Thanks brother. I checked it with Makita as well and they said it's normal with these new inflators.

@tobris3738 11 месяцев назад

Can you use it as a dust blower?

@ToolsAndStuffOFFICIAL 11 месяцев назад

No.

@odeean 2 года назад

Screw on = bought. I have the small one and I can't reach behind my backwards truck tyres to attach it. I have been using dewalt.

@huguesdollie6239 8 месяцев назад

why Makita has not a trigger hold : incredible. I have Makita platform but I won't buy a Makita inflator till this issue is solved ! strange from Makita Cie , they don't read the comments ???

@truebluekit 2 года назад

I was hoping that these things could be used like normal air compressors, and not just inflators. Would become a lot more versatile and I'd buy one just like that

@ToolsAndStuffOFFICIAL 2 года назад

You're asking a lot to expect this to power a nail gun or any other pneumatic tool.