NV231/NP231 Transfer Case Rebuild Part 1

Подписаться 2,5 тыс.

Просмотров 43 тыс.

50% 1

Getting down and dirty showing ya'll how to tear down a NV231/NP231. The first episode in our two part series of rebuilding one and installing a slip yoke eliminator kit. Don't forget to like and subscribe to catch part 2 and many more informative "how to's with mike.
Disclaimer:
Due to factors beyond the control of The ASAP Automotive Channel, I cannot guarantee against improper use or unauthorized modifications of this information. The ASAP Automotive Channel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. The ASAP Automotive Channel recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of The ASAP Automotive Channel, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not The ASAP Automotive Channel.

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@twistedwired Месяц назад

Great video. I have a knocking sound coming from my T Case when driving, I was hoping to get a clue what it is from this vid.

@triplecranks 3 года назад

An easy method for pulling blind hole needle bearings is to put grease in the bottom of the hole. Take a shaft (I use a wooden dowel) of the same diameter. You could also use an old transmission shaft. Drive the shaft in with a hammer with a few sharp blows. The hydraulic pressure will push the bearing right out. Works every time. I use that method for removing pilot bushings in a clutch plate.

@slant6guy 4 года назад

Using the 6mm bolts to get that damper off helped A LOT here on the _NP231J SYE upgrade...while in there did the 3-->6 gear planetary swap, Teraflex 2WD low + the 1"-->1-1/4" wide chain upgrade_ . This was a good video to watch before the NP231J here was worked on. Thank you *ASAP Automotive Channel* for this video!

@bob5856 Год назад

Great tip on raising the blind puller up a bit. I was about to give up using my puller. Your trick worked great!

@yosemitesamiam 2 года назад

Best resource on the net! Thanks for this. My kid’s XJ tcase is 100% after one winter of abuse.

@paulkaufman4901 4 года назад

I would have appreciated a listing of all special tools needed. I caught the OTC Seal driver kit number but, did not get any useful info on the correct pliers needed or the other puller you used on the bearing. Maybe you can add that for future viewers?

@martinmoffitt4702 3 года назад

Thanks learned a a lot... unfortunately our patient had the chain let go and come through the case.....so a junk yard special is going back in(I recommended a rebuild but they are selling it..) Merry Christmas BE SAFE!

@erniemark19621 4 года назад

For cleaning parts I use mineral spirits in a spray bottle. Great for plastic parts. It's great for degreasing before painting also.

@MacGyversWorkshop 5 лет назад

You need my expanding snap ring pliers LOL!

@orygunchainsawmassacre6761 9 месяцев назад

Damned good vid

@robertpc100 3 года назад

can you tell me what kit you bought for your re-build and best deal for a good quality product.ive looked at lits on e-bay that are like 154.00 with everything but not sure if all parts are acceptable or if bearings are re-manufactured and such.Also it mentions for 15mm bearing shaft or something and i havent torn into mine yet but plan today cause im doin sye kit and clutch but just wanted to get new chain and pump and seals and bearings i know ill need .Can you point me in right direction.You have did a great job and im trying to follow you.mine is a 231-j and i know its new process or new venture as says on my sticker and basically same.i just dont want to get stuff i dont need and a good product.Need some help,im confused with all ways amazon and e-bay list stuff.Thank you and awesome job