P0741 OBD-II: Torque Converter Clutch Circuit Performance or Stuck Off - Weak Wire Connection -FIXED

Подписаться 1,4 тыс.

Просмотров 105 тыс.

50% 1

The content of this video is put forth as INFORMATION and ENTERTAINMENT purpose only. Any action you take upon the information on this website is strictly at your own risk.
I able to fix my Check Engine Light's (CEL) P0741 code on my 2007 Toyota Corolla by changing the Transmission oil; however, last week after I installed a new fog lights on this car, the Check Engine Light turn on again and the code is the P0741 - What the heck!!! P0741 is back !!!
I able to trace down what I did. Due to wire connection of fog light wires need to hook up to the battery terminal, I disconnect and reconnect the battery terminal. During this process, the battery terminal and area is pretty corrosive and I decided to clean it up with Baking Soda and then with hose it down with water by a garden hose. I believed the water leaks into the wire connections under/next to the battery and make those connection weak again. ( because the Check Engine Light is on and off and not always on.)
I able to determine the bad one is the one on the far right because I able to disconnect and clean the one on the left but CEL still on and off (your case may be different) However, I have a tough time trying to remove the one on the far right and the connector still won't come out or move at all. I have to go to Plan B.
I decide to use a pick to open up the soft rubber which is surrounded the wire and then put the electronic cleaner tube inside and spray / clean it up that way. After that, I use the same method to spray in the blower air to dry it up. After that, I connected the battery terminal and the Check Engine Light error code's of P0741 did not come back again.
I hope this work for you and resolve the stupid code of P0741.
Please let me know if you able to disconnect the far right connector and how did you do it. Is there a clip at the back or use WD40 or special trick to pull it up by leverage with screw driver or remove battery to make more room to work on it.
Thanks for watching.
please comment, subscribed and like. Please let me know if this resolve your P0741.
Other possible issue/fixes for CEL's P0741.
1) Dirty Transmission oil - Changed the transmission oil. (Toyota type T-IV or Aisin Brand)
2) If CEL comes back after 2-3 times transmission oil changed, then you may have to change Transmission filter (dirty filter) and at the same time change torque converter lockup solenoid (ROSTRA 520257), it was only holding with two nuts and a wire connector.
Since the transmission pan is dropped, this is the best time change the solenoid, it is about $50-60 depends on your model.
Changing Transmission Fluid video.
2009 Toyota Corolla Change Transmission Fluid as follows:
• How to change replace ...
2007 Toyota Corolla Change Transmission Fluid / P0741 as follows:
• P0741 OBD-II: Torque C...
Useful video from Scott Kilmer on Corolla's P0741 starting at 3 : 20
• I Won't Fix This Toyot...
Thanks for watching.

Опубликовано:

7 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 140

@Windows121165 11 месяцев назад

Good video, I had the same problem with my 2006 Toyota Corolla. I took it to O Reilly to get the check engine light checked for free and they showed me the tester with the code P0741. I took a picture of the tester and took it to my local mechanic so I could get an estimate. I showed him the picture of the tester with the P0741 and he gave me an estimate of $2500 to fix it. Way too much so I came back home and saw your video. I went to Home Depot and bought some WD 40 electronic cleaner. I watch your video again to make sure on the process. I took the wires off and cleaned them just like on your video. I put them back together and It didn't work the first time and the car wouldn't start either. I must have tried like 3 or 4 times taking the wires off and cleaning them. The last time I tried I put a small screw driver in one of the connectors and saw I had bent one of the little pins in the connectors. I bent the little wire pin back with the little screw driver and put it back together being careful not to bend it again. This time it worked the car started and the check engine light was not on anymore. I just did it yesterday and I took the car to work today and the check engine light is still not on so far. I hope it doesn't come back on. I have been driving it like that for a year because I didn't want to spend that much money on the car. Another problem I had was when I replace the battery back and reconnected it. The car was idling really low and stalling . So I check RU-vid again and it shows how to reset the computer in the car by Turing ignition on three times and on the third time you start the car and let it idle for ten minutes. That worked too my car is running good now, no more check engine light and no more idling problems. Thanks to you sir.

@diycheapdaddy2113 11 месяцев назад

You are very welcome. I am glad you able to fix the issue. Thanks so much for the above information for other youtubers. Thank you for watching.

@elkuartostudio 8 месяцев назад

Update?

@Windows121165 8 месяцев назад

@@elkuartostudio The light came back on two weeks after I that. So it means I only reset the light. I sold the car as for 1500 and bought a 2017 Corolla SE. Good luck with your car. 2017 Corolla is much better now, it only has 4200 miles on it. My last one had 187,000 miles.

@elkuartostudio 8 месяцев назад

@@Windows121165 I want to drive it at least 6 month to buy a new suv. You think it can hold that long?

@Windows121165 8 месяцев назад

@@elkuartostudio I drove my 2006 Corolla with the light on for over a year. It would go off for about a month and come back on. They gave me that code P0741 about the transmission. But my transmission was okay so I drove it like that no problems. I disconnected the battery so I could reset the light. It worked so I sold as. The new Corolla is a lot better.

@odkdsjf Год назад

Thank you so much! My car had had this error code for many years. My multiple Internet search results, and code readers stated it was a bad solenoid or clutch. My mechanic stated it could be a bad sensor. I always thought it would be replacing a part, so I never got around to resolving it. But, after watching your video, I decided to remove those two connectors and clean them. However, when I remove the second connector, the female connector was full of oily water. I removed 99% of the water and moisture with paper towels and Q-Tips. The error code is now finally gone! I wish I knew this years ago. Lesson learned: don't rinse your engine with water. Use an engine cleaner or WD40 instead. If using WD40, I wipe it off from the bigger surfaces afterwards so that dirt doesn't stick to it. If using water, cover all the sensors and connections with plastic bags or food/plastic wrap and duct tape beforehand. By the way, to remove the second connector, I inserted a short, narrow flat screwdriver from the bottom up at an angle to un-clip it from its female connector while pulling the male connector with my other hand. Thank you again. Regards

@diycheapdaddy2113 Год назад

Hi, Adolfo, thank you so much for your additional information especially on how to remove the second connector. As other youtuber commented here, this may be a connection/wires related issue and may not be a solenoid issue. Thanks for watching and thank you so much for your comments. 👍

@elcomparomo8295 Год назад

Same thing with my second connector. Noticed the oily water as soon as I removed it. I tried my best at removing all of it but it was impossible to remove it all. I just reconnected my battery and need to drive it so the code can reset. Hopefully it doesn’t come back. Did yours stay off?

@diycheapdaddy2113 Год назад

@@elcomparomo8295 Yes. My stayed off and so far no code after posting this video at Nov, 2021 and I able to pass smog check. In California, any check engine light on is a automatic fail; therefore, the code P0741 has to be fixed and it means big buck due to related to transmission. Luckily after cleaning the connection, my P0741 code is gone and no more check engine light. Thank you for your comment and thank you for watching.

@arvionmathews4487 9 месяцев назад

@diycheapdaddy2113 is the code still off and mines is a p0744 clutch circuit intermittent

@arvionmathews4487 9 месяцев назад

@@diycheapdaddy2113it says sum about a circuit i.think the plastic circuit that's connected to a wire or something its probably dirty or got a short

@lindseytriplett3250 Год назад

Your awesome! I cleaned my connections and check engine light is off.

@diycheapdaddy2113 Год назад

Thank you for your kind comment. 👍I am so happy it works for you. Thank you so much for watching.

@W.Khairi Месяц назад

Exellent demonstration of connector placement and problem solving, Thank u.

@diycheapdaddy2113 Месяц назад

Thanks for the kind words. Thank you so much for watching. 👍

@eliusamuelrodriguez1988 2 года назад

Hi I Own The Same Car Corolla 2007 Same Code P0741 I Replaced The Torque Converter Change The Fluid Everything Original Code Still On I'm Gonna Try The Wiring Like You Did Because The Car Shifts Fine Thank you for the video hopefully it also works for me 🙏✌

@diycheapdaddy2113 2 года назад

Thanks for your comments. I think my corolla is a combination of dirty transmission fluid and weak/bad wiring. I hope this works for you after you cleaned those wire connection to the transmission (especially the far right). Thanks for watching.

@eliusamuelrodriguez1988 2 года назад

@@diycheapdaddy2113 Do You Recommend me to also replace the Transmission filter and the solenoids wish solenoids should I replace ?

@diycheapdaddy2113 2 года назад

I think I would do the cleaning on the connector first and if it did not work then I would perform the transmission oil change because it is still necessary for the transmission to have clean fluids and also it is easy to perform. If it still not working, then I would drop the pan and change the transmission filter and at the same time, change the solenoid. I have my first video related to P0741 on here and it has lot of information on the video's description SHOW MORE and also under my comments. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mMnMOqQLOWU.html If you go ebay below, on the listing's picture, it has a solenoid and the transmission, the TC solenoid is located on the corner, for my transmission, it is the one using the long bracket holding with 2 nuts and a wire. It is next to the transmission filter. The ebay picture did not show the transmission filter. As long as you remove the nuts holding the transmission pan, it is on that corner as shown in ebay. Hope this help. www.ebay.com/itm/301082908347?epid=153824054&hash=item4619f096bb:g:z34AAOxyOlhS6Dko

@eliusamuelrodriguez1988 2 года назад

@@diycheapdaddy2113 Thank You So Much For Your Help I Will Do That 💯

@diycheapdaddy2113 2 года назад

I am not sure how long that listing/picture will stay up; therefore, 1) move cursor to the picture. 2) do a right click, 3) do a "save as" for future references. Thanks for your input comments.

@diycheapdaddy2113 2 года назад

Please click above "SHOW MORE" for more information. Thanks for watching.

@seang402 Год назад

Thank you so much . All I wanted to know is where Torque Converter Clutch Solenoid connection was.

@diycheapdaddy2113 Год назад

I am glad this video helps. I would clean that wire connector first before spending money on ECM, Torque convertor, solenoid or even the transmission. Based on my research, a lot people change what I mentioned but the P0731 still come back within months. I truly believed it is the wire connector issue and nothing to do with the transmission related parts. Thank you for your comment and thank you for watching.

@subzero___ 5 месяцев назад

@@diycheapdaddy2113 any update is the code gone?

@diycheapdaddy2113 5 месяцев назад

@@subzero___ Hi, Subzero, the CEL did not turn on and no error code yet; however, we did not drive the car that much ( < 4000 miles per year) compare to the old days. Thanks for your comment and thank you for watching.

@kevinc1851 2 года назад

We had P0741 for the past 6 months on our 2005 Vibe (same as Matrix), reset would have the code come back in a few minutes. I did a filter and fluid change two days ago since several people said it resolved the same issue. My kid has been delivering pizza for almost 20 hours of driving since the flush and so far no codes. I make automotive coils for brake and transmission systems and can only venture a guess that the dirty fluid / clutch debris was causing the solenoid to stick and the fresh fluid allowed it to move free again. Cross my fingers, if it is not broken don't fix it.

@diycheapdaddy2113 2 года назад

Thanks so much for your information. You are correct, the major cause is the dirty Transmission fluid and/or Transmission filter and last is the TCC solenoid. I have put all the details on above "SHOW MORE" section under video description. I hope we can try the easy way first before performing major repairs. I totally agreed and if no CEL, I would not touch the transmission wire connectors; however, if someone drain and fill transmission fluid 3-4 times and also changed the Transmission filter and TCC solenoid and P0741 come back again with no performance issue on transmission. This may be something look into. Thanks so much for your comment and watching.

@keithc8108 Год назад

Has the CEL light come back on yet, on the Vibe? I'm having the same issue with my 05 Matrix!

@ayvenaswulff6820 Год назад

@@keithc8108 I changed transmission fluid, it did a great job on performance but CE light is still there. So it's why I'm here watching about dirty wires.

@leonardjuarez1 Год назад

I been driving my corolla with this code for over 4 years and no damage i know this its common conexion problem I see many people just assume the clutch converter its bad but don't solve the problem in many cases I think cleaning this wires maybe solve the problem

@arvionmathews4487 10 месяцев назад

Hey did it come back onm

@JorgeSanki Год назад

amazing, i did what you said. I disconnected the cable and EFFECTIVELY, everything was submerged in oil, I don't know how the oil got to that connector but I took it out and cleaned it with circuit cleaner and that's it. NO MORE CODES ON MY DASHBOARD. THANK YOU

@diycheapdaddy2113 Год назад

You are very welcome. I am so glad this video able to solve your issue with one simple cleaning on the connector. Thank you for your comment and thank you so much for watching. 👍

@diycheapdaddy2113 2 года назад

I found this very useful video from Scott Kilmer on Corolla's P0741 starting at 3 : 20 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-W7LG2tDCgF8.html Thank you for watching.

@keithc8108 2 года назад

Did your code ever come back after cleaning the connection?

@diycheapdaddy2113 2 года назад

@@keithc8108 My code did not come back. I actually passed the smog check with no check engine light turn on. In California, if Check Engine light is on, it is a automatic failure. You can review my other video on "how to pass smog check". Thank you for watching.

@subzero___ 6 месяцев назад

@@diycheapdaddy2113 can you pass smog if you have P0741 pending with no light on

@diycheapdaddy2113 6 месяцев назад

@@subzero___ Hi, subzero, that is a good question because does pending mean fail? or may be fail? especially there is no check engine light. Based on internet, if the code is erase, smog check station will know it has been erased recently and it will not pass. If the battery is disconnected and the code is gone due to no power, smog check station will know and car most likely won't pass too. In order to pass, the car has to be back normal driving under drive certain condition with certain stop, certain city driving, certain highway in order to get back to the normal way for certain xxx miles and times. I think the best is to check Smog Check station to confirm "what if" it has pending code. You may also discuss with smog station with option such as "pre-test" or "pass or no pay" or "free re-test" options if those are available in your area. Thanks for your comment and thank you for watching. Good luck.

@AngelHernandez-qe3nf 3 месяца назад

The connector has a tab which you have to press. It is located to the driver side

@diycheapdaddy2113 3 месяца назад

Hi, Angel, thanks for the information. Thanks for your comment and thank you for watching.

@michaelgarcia9362 Год назад

Im going to try it out now

@diycheapdaddy2113 Год назад

Hi, Michael, please keep us posted how it goes, thank you so much for watching. 👍

@angelcontreras5736 2 года назад

Excelente explicación en mi caso tengo un corolla 04 me marcaba el código p0741 desconecte el conector y estaba lleno de aceite por eso me marcaba ese codigo

@diycheapdaddy2113 2 года назад

Creo que el aceite hace que el contacto del cable se confunda. Me pregunto de dónde viene el aceite. Gracias por tu comentario y gracias por compartir tu solución. 👍

@angelcontreras5736 2 года назад

La verdad el aceite no se como llego ahí el carro tengo una semana con el creo que el antiguo dueño le lavo el motor h por eso el aceite no encuentro otra explicación

@diycheapdaddy2113 2 года назад

@@angelcontreras5736 Tiene sentido que la limpieza lo haga bonito pero también acumule todo el aceite y la suciedad. Gracias por tu contribución.

@jennyyojanajoyaamador3208 Год назад

Que sensor es ese

@elcomparomo8295 Год назад

Oye, ya no te volvió a marcar el código? Acabo de hacer lo mismo que tu. Ya conecte la pila con esperanzas de que no me vuelva a salir. Fui a un taller se transmisiones y me dijeron que le tengo que cambiar toda la transmisión. Acabo de comprar el carro hace dos días y ya empezó con sus cositas 😂

@asarcik Месяц назад

so My Chevy Aveo lost connect gear.. No move R and D.. I touch the socket its run... and it give P0741 is it same prob ?

@diycheapdaddy2113 Месяц назад

The code P0741 apply to the same condition/issues and it is related to torque converter/transmission/transmission oil/solenoid. I would unplug it and check for lose contact and since you disconnect it, I would clean it and put it back tight and see what happened. The connector is the cheapest and easy way. If you watch the link on my comment on Scott's video, the P0741 was not major issue; however, the check engine light will not pass smog in California; therefore, you cannot renew your car registration. Thank you for your comment and thank you for watching.

@asarcik Месяц назад

Pleasure and thanks for feedback ı will update now my car in workshop

@asarcik Месяц назад

@@diycheapdaddy2113 When I'm on road suddenly transmission is gone thats like rew up on N and I pull over car. I check that connector and touch a screwdriver after car select D and R gear.. after happen again.. sorry for delay answer thanx

@diycheapdaddy2113 Месяц назад

@@asarcik Thanks for the update. For my corolla, there still a cable connected to the transmission in order for it to shift from P to D, R or N. I believed my connector's contact is dirty which created the Check Engine Light because wrong or no signal is send to the solenoid. No so sure how Chevy works. Thanks for your information.

@sergiopelaez560 2 года назад

Hi.. i have the same issue.. i have change the transmission oil, filter and even replaced the solenoids from the transmission also replaced other engine sensor suggested in other youtube videos and the check engine light went away from the dashboard but when scanned it still shows ... code P0741 still show...Now just today the check engine light came up again after several weeks of not being on.. I been looking for a solution and i think i going to do what you have suggested here ... Hopefully is just the connectors that may need cleaning.. I will update if this works or not.. Thank you for the video and the help..

@diycheapdaddy2113 2 года назад

I have similar issue like yours but after I cleaned the connection as last resort, the CEL's P0741 did not light up again. I hope yours is the wire connectors too. Thanks for your comments and thank you for watching.

@sergiopelaez560 2 года назад

@@diycheapdaddy2113 Thank you.. after performing all the other changes hopefully this will fix it.. I will clean them up this weekend and I will update ... Hopefully this is the issue..

@diycheapdaddy2113 2 года назад

@@sergiopelaez560 I found this video from Scott Kilmer on Corolla's P0741 starting at 3 min 20 second ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-W7LG2tDCgF8.html Hope it helps what it is. Thank you for watching.

@hyrantha4397 2 года назад

Yes it should work. It worked for me.

@angelcontreras5736 2 года назад

Un amigo me dijo que puede ser la computadora que este fallando y dar ese código

@anthonyampiah4043 Год назад

Nice work

@diycheapdaddy2113 Год назад

Thanks for your kind comment. Thank you so much for watching. 👍

@Kreaturepianet 2 года назад

I worked on Toyota corolla 2007 with po741 I changed engine coolant Temperature sensor code went away . That controls torque lock up.

@diycheapdaddy2113 2 года назад

That is excellent information. Thanks for your advice. This really helps a lot. 👍

@Kreaturepianet 2 года назад

Any time

@keithc8108 2 года назад

I have a 05 Matrix. I notice the radiator electric fan blows a lot. And I got a P0741 code. I wonder if I need to change my coolant, as you did. Might work ..Thanks

@arvionmathews4487 9 месяцев назад

@@Kreaturepianet wat about for a p0744

@samoliveros6678 7 месяцев назад

En mi caso funciono.toyota corolla 2007 le limpie.los conectores.y le hise cambio.de aceite i filtro.ala transmission..ya llevo 800 millas manejandolo.y no regreso.la luz

@diycheapdaddy2113 7 месяцев назад

Hola Sam, me alegra mucho que te funcione. Muchas gracias por tus comentarios y gracias por mirar.👍

@sylviasmith3471 Год назад

I have multiple codes scanned out after changing my transmission fluid in about 2 days ago and the codes are. P2757 and P0471 any help please. Its a 2014 Toyota camry SE

@diycheapdaddy2113 Год назад

Do you have any check engine light turn on or these 2 OBD code happens before the transmission fluid change? It is rare when your car runs perfectly and suddenly have Check Engine Light and codes related to transmission 48 hours after the fluid changed. You may want to double check your transmission level and trace back what may go wrong. I don't know much about these code and Toyota Camry; however, I believed you can search the two codes out. Here is what I got from internet: A P2757 code will be reported when the vehicle's onboard powertrain control module (PCM) detects an issue in the torque converter clutch pressure control solenoid circuit. This aspect of the powertrain automates the clutch application in order to optimize the engine's use of fuel. OBD-II Code P0471 is defined as a Exhaust Pressure Sensor "A" Circuit Range/Performance The Exhaust Pressure Sensor tells the engine control module (PCM) how much pressure is in the exhaust manifold. If the PCM determines there is an incorrect signal from the Exhaust Pressure Sensor, the PCM will set code P0471. Notes: If your 2014 Camry is CVT transmission, there is a procedure need to be follows, it is more than a simple drain and refill. Good Luck.

@TheTransmaster92 4 месяца назад

how did you get dirt in your transmission

@diycheapdaddy2113 4 месяца назад

The dirt/water/grease is on the connector outside the transmission. My guess is during daily driving, the oil grease, dust, road dirt and rain water accumulate on the top of the connector and eventually go inside the connection/wires. Thank you for your comment and thank you for watching.

@musty.diesel 2 года назад

I got the same code but for a 2005 Honda Accord the code came up as pending code after I ran over a puddle of water I’m going to do the fluid change or could it be a connector that got wet what can I do

@diycheapdaddy2113 2 года назад

Sorry for the late reply. Got some plumbing and fridge issue in the house. I don't know much about Honda Accord; however, I can tell you this P0741 is a false alarm on my 2007 Toyota Corolla because I am 99% sure it is not transmission related but a wire connection issue to the transmission. As of today, my car still running great without error code and the transmission is shifting flawlessly. My suggestion is found out the similar connection wire to the transmission on your Honda Accord, it may be similar issue due to loose or corrosive wires. Also, I don't think it will hurt if you never change your Honda's transmission fluid. Also, please make sure you follow the Honda Manual Step by Step 100% and use only OEM Genuine Honda Transmission for your particular Year and Model. Honda Transmission is very picky. You have to use OEM Genuine Honda Fluid. No if or But. Even if you did not fix this P0741 after OEM fluid change, changing trans. fluid or/and transmission filter is part of the maintenance scheduled and it should help extended your transmission life for other future transmission related issues. Good Luck and hope you can fix it.

@francisco4099 2 года назад

Did u let the electric cleaner sit for a while? Before u spray the air duster

@diycheapdaddy2113 2 года назад

I did let it stayed for a little bit; however, those electric cleaner evaporate very fast and you can test on some test area and see how fast it evaporated therefore, even I let it stayed longer than need, the cleaner should be already gone. The air duster just to make sure it can reach some corners or odd area, just in case. Thank you for watching. Notes: As of today, the code did not come back and the transmission is working great.

@jeffdenney4148 Год назад

What’s the part number and location thanks

@diycheapdaddy2113 Год назад

Hi, Jeff, I don't know the part name but it is basically a Wiring Harness connected to the transmission. The location is on top of the transmission. I believed those wires are then connected to the solenoids inside the transmission. I believed after so many years, the connectors are opened to battery acid (right under the battery), rains, snow, oil, dirt and water contamination and became corroded or have a contact issues. Thanks for your comment and thank you for watching.

@user-zf2te9gl7m 2 года назад

Hi sir I have sam the cod and p0743 +p0741 But i have Hyundai elantra 2010 Can uou hlpe to me How to fix? And im electrical Eng

@diycheapdaddy2113 2 года назад

Hi, I don't know much about Hyundai Elantra; however, the code are generally across the board; therefore, if you have not change your transmission fluid for a long time, I would give it a try because it may cause by dirty transmission fluid. In additional to that, even it may not resolve the code of P0741 but good fresh transmission is good for the parts inside the transmission even if you perform the fill and drain, it only remove portion of the transmission fluid but it should make the transmission parts last longer. Thank you for watching.

@WetheJury-gn6vx 11 месяцев назад

When I lower my driver side window that code pops up

@diycheapdaddy2113 11 месяцев назад

This is very strange because lower window should not related to Transmission torque converter lockup solenoid's code P0741. You may want to reset it and see whether the same code come back again. Thanks for your comment and thank you for watching.

@richardjoyan4819 2 года назад

Where did you really put electronic cleaner, wondering there was no space to put the liquid, will appreciate it if you response

@diycheapdaddy2113 2 года назад

Hi Richard, you can try like my way in video by using the hook open up the wire a little bit so that you can put the electronic cleaner tube inside. Also, it depends on your model, if there is one plug/wire is not use, you can use the hook to pull out that little round plastic (make sure don't drop it or loose it) then you can use that hole to spray the cleaner. After it is dry, you can cover it up again to avoid dirt or water goes inside the connector. The best way is to open the connector but I have arthritis on fingers and it is not strong to disconnect the plug especially the connector is in an odd position. Hope this helps, Thank you for your comments and thank you for watching.

@ayvenaswulff6820 Год назад

Hello! Can you give me the proper name of the wires? Is it transmission wires? How can I Google this part to get more information? Thanks.

@diycheapdaddy2113 Год назад

Hi, thank you for your comments. I don't know the proper name but it is the wire harness assembly connected to the transmission. Thank you for watching.

@ayvenaswulff6820 Год назад

@@diycheapdaddy2113 thank you! I'm gonna look at it in my matrix today. I have P0741 but I don't feel the problem with shifting. The car needs a couple more seconds to shift and it makes a small bounce but the car is old, I have 200k miles. I guess it's ok for old cars to work a bit slower

@diycheapdaddy2113 Год назад

@@ayvenaswulff6820 You are correct and same issue on my 07 Corolla. There is no symbol of transmission issue except the check engine light's (CEL) of P0741. There is a video on Scott regarding this issue which I have posted here.. Here is that video just in case. It starts at 3 : 20 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-W7LG2tDCgF8.html In my opinion, I would keep driving except in California, we have to smog check once every two years and I need to resolve that CEL before smog check which I did by cleaning it and avoid water get into it again. As of now the CEL did not come back yet. (knock on wood). Good Luck.😃

@lindseytriplett3250 Год назад

Is there a gasket behind the electrical plug on the car? How would transmission fluid get in the wire harness

@angelcontreras5736 2 года назад

Me comento un amigo que puede ser la computadora que da ese código p0741 que hay personas que le pusieron otra transmisión y les sigo marcando ese código y llegaron a la conclusión que la falla es la computadora

@diycheapdaddy2113 2 года назад

Acordado. Hay un retiro en la ECU; sin embargo, cuando reviso mi Corolla 2007, no está en la lista. Al buscar en Internet, existe el caso de que las personas cambien la transmisión / convertidor de par debido a este código, pero el código vuelve a aparecer en unos pocos meses. gracias por tus aportes.

@alisawaters5908 2 года назад

I have the same code on my 2005 Toyota Corolla ce do i need a new transmission someone please help me out

@diycheapdaddy2113 2 года назад

Please click above "SHOW MORE" under the video description. It has lot of information related to this code. In my opinion, I would perform the transmission oil change first (even it may or may not work but it did not cost much compare to a new transmission or torque converter. Also, it is part of the maintenance and at least your transmission got the new fluids benefits in the future). Thank you for watching. Please click "SHOW MORE" on this video. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mMnMOqQLOWU.html

@anyangel_34 Год назад

Si tú transmisión está funcionando bien, porque tienes que cambiarla ? Claro que no. Si sientes que la transmisión hace los cambios de marchas correctas. Debes verificar si los cables están surfactados y luego de eso cambiar el aceite y filtro de la transmisión. Y si sigue la falla entonces cambia la caja de válvulas. Y si después de todo eso el código persiste entonces deberías considerar comprar una nueva transmisión.

@randolfruiz7565 Год назад

@@anyangel_34 Ese código me ha dado dolor de cabeza jjj

@hectora3692 2 года назад

This is weird cause I put the diagnostic scanner in my Malibu 2002 and also gave me the code PO 741 that means the same valve defective . Can be use on Chevrolet and Toyota ? I was told to keep driving driving eventually it will reset but in my case no luck yet 😩 I will also check my battery terminals / my transmission fluid and if I can figure out where exactly is located the such part Will replace it only cost about $ 39.00 new

@diycheapdaddy2113 2 года назад

Hi, Hector, thanks for your comment. Based on my research, the cheapest way to fix this is to perform a transmission fluid change. Also, even it may not work to on the code, at least you have new trans. fluid and should be better on the transmission in the long term. Thanks for watching.

@jennyyojanajoyaamador3208 Год назад

Civic 2012 que pieza es

@diycheapdaddy2113 Год назад

No estoy seguro acerca de Honda, pero puede ser similar, consulte su manual, pero en Toyota es el solenoide del embrague del convertidor de par, pero en algún momento puede ser causado por aceite de transmisión sucio, podría ayudar si cambia el aceite de transmisión y si todavía sucede entonces es posible que desee cambiar el filtro de transmisión y el solenoide TCC. Gracias por ver.

@angelcontreras5736 2 года назад

Cual es el nombre de ese sensor de 5 pines?

@diycheapdaddy2113 2 года назад

Lo siento, no sé pero no creo que sea un sensor, creo que es una conexión a algo, puede ser un "sensor". Gracias por tu comentario. 😁

@angelcontreras5736 2 года назад

Necesito saber el nombre de esa pieza para reemplazarlo por que en unos días se llena de aceite no se porque algún oring o empaque

@diycheapdaddy2113 2 года назад

@@angelcontreras5736 Recuerdo la última vez que fui al concesionario Toyota, pudieron sacar la microficha de mi automóvil y ubicar las piezas para mí, y esas son las piezas y la ubicación del solenoide TCC de la transmisión. Mientras escribía ese número de pieza, el caballero fue muy amable y me imprimió el número de pieza completo y el diagrama. Creo que puedes hacer lo mismo en ese "sensor"/"interruptor" alrededor de la transmisión. Gracias por tu comentario. Buena suerte.😁

@benjaminmoyo7036 2 года назад

Good Afternoon this is Benjamin i have followed your video on 2007 corolla just want to learn the colour code for the transmission solenoids.

@diycheapdaddy2113 2 года назад

Hi Benjamin, thanks for your comments; however, I do not have the color codes of those solenoids. I do know this can or may be related to the TCC lockup solenoid (not working or the opening has dirt on it). That solenoid is near the transmission filter with 2 bolts holding it. If you review the comments on my first video, I have some information pointing to that. Thanks again for watching my video.😁

@heatpumpdiy Год назад

Did the P0741 come on again?

@diycheapdaddy2113 Год назад

Hi, Peter, the code did not come back. (knock on wood). 😁 Thanks for your comment and thank you for watching.

@heatpumpdiy Год назад

@@diycheapdaddy2113 我部是05matrix 几年前开始有0741,一直都找不到原因, 兩年前有時会無左後波, restart又会好返, 我也是在波箱harness 噴了cleaner就再無出現, 但0741code仍然時有時無, 我一直也觉得是接觸不良

@diycheapdaddy2113 Год назад

@@heatpumpdiy 我高度認為這與接觸有關。由於這是一輛舊車並且里程數很高，我不會在變速器上花更多的錢。根據我在網上的研究，有人花很多錢換變速箱，變矩器 (torque convertor) 和電腦控制板 (computer control board)，P0741後來還是回來了。感謝您的評論，感謝您的收看。

@heatpumpdiy Год назад

@@diycheapdaddy2113 Matrix 是一部非常实用的車, 十二尺長的木方也可以載上, 兩年前我也是只能拔出大插头, 另一个小插头同樣也折不出, 明天我会試下拔出小插头再噴cleaner試試,

@diycheapdaddy2113 Год назад

@@heatpumpdiy Hi, 陳彼得, 我也會盡量不在大雨中開車。好像線束 Wire Harness 可能不防水請保持讓我知道最新消息。祝你好運