Predator 212 Throttle Linkage 

After hours of searching I found your awesome video. Outstanding! Great job and thank you for sharing.

i have a 2 seater manco silver fox with a predator 212 stage 1 performance kit and a bigger jetted carb. on 18 inch street tires got it up to 37 and it was still climbing kinda quick on the GPS speedo lol. Thanks for the video My gas pedal has full range of motion on the carb for my linkage setup. i just had to add a zip tied and stronger return springs and it working fantastic!!!

Thank you you actually gave me a new idea on running my linkage and what else i could use i just did a swap on my mini bike its a MMB80 and I just put the Preditor 6.5 hp 212cc engine on it so again thanks for the help sir

Just what I needed when I needed it on my 212 conversion. THANKS

Just what I was looking for! Thanks

Great video explaining how to hook up your throttle assembly for mini bike and go cart.

I stopped your video at 4:31 and made this piece using the old con rod from governor...took about a minute...works great....

do u realize that if u disconnect those springs and leave the governor assembly in the motor the weights in the govener will explode from running at high rpms that's why we remove them

Thank you. I removed my governor and was stuck as to how my throttle was to be hooked up. This video need to be at the end of "How to remove a governor " video.

the small return spring you where talking about where could I find on of them my engine did not come with it

Great job! Just what I needed to know. Thank you sir

I like your vids Keith, I did this on my predator after watching. So simple and effective, thanks!

Thanks for your video you have such clarity.

Hey Keith what type of cable would fit through the hole and do you think the same linkage setup could be applied to a go kart?

Ok so is it safe to simply disconnect the governor rather than take it out completely from the engine? Safe as in keeping the gear and arm in with necessary billet parts inside too.

This is a great idea after governor removal.. removing the throttle to governor rod and spring don't change the governor inside the crank case..it is still being governored by the plastic gear located in the engine..but this does increase rpms at a quicker rate.. so acceleration is increased, but does nothing for top end... If you are going to invest into a stage 2 kit or greater than I would recommend the governor removal, but I won't do it with less or stock.. the governor gear inside the housing is plastic and will surely break or melt from higher temps and possibly jam up your cam and cause you to blow your engine.. build it up before jumping the gun..

hi I have a 5hp I/c brigs and Stratton engine, trying to put it on a go kart bur having trouble with the throttle linkage could u give some advice or a video, thanks.

please help...bought a predator 212 engine for go kart. when you start it, it us already at full throttle. the adjustment screw on carb only speeds it up. did i just get a bad 1? have you heard of this problem? than you

Thanks your video was helpful is it ok not to remove the govner from inside the motor

Good video I am going to do linkage like that for my Predator motor ATV build.

keith,well now i know why i broke my collar bone two days ago. i literally just got started into mini bikes last week so i don't know too much. here my mess up i only used one coat wire to carb slot to throttle that's it.. so when i started motor and turned choke off my bike took off and i have no kill switch so i wrecked. and handle bar went right in my collar bone and broke my collar bone. i tried to bypass the governor. i took the main thick rod from governor to carb off and the return spring from governor to throttle off. all i did was made one rod to carb from throttle short rod and nothing else so doesthat explain why my bike took off? cause i didn't make a rod for throttle to governor for a return? it seems now that it is obvious why my bike took off cause i had no hook up to control governor to throttle?

Thank you very much and congratulations sir

Looking to find the part # for the throttle arm he references at 04:30. Can anyone help? The one we have where the screw limits how much it moves has started to bend back and wanted to get it replaced.

Your the best I used the metal piece that connect to the carb instead of the hangers my cart is fast now lol 💘

I did this the other day and fired it up today and when I put it in run position the motor started revving extremely high with no throttle applied

what is the little spring for ?

I took my governor off of mine and adjusted throttle assembly and all that good stuff... Now it wont start... I have no idea why.. any ideas??

Thank u so much this helped so much thank ur awsome lml thank u 👍👍👍👍👍

This video is about Throttle Linkage, not governors. In the description, I have included links to video's that explain how to "correctly" remove a governor (wheel/arm) and how to correctly plug the holes. Also, I've made clear that disconnecting your governor makes your engine dangerous. As I said, "Over revving will destroy your engine". That's why they put governors in.

Nice way to Bale on the project

love the video.

Great video:)

Awesome video boss ! So after you remove all springs from the governor , and hook the little link up on either both of the sides of the throttle arm , the governor shouldn't activate at all ? And will the stock plastic fly wheel have more of a chance of exploding due to over reving ? Should I get an aluminum flywheel ? Thanks , and sorry for all the questions haha .

I ordered my throttle from omb warehouse, it fits behind the gas tank and doesn't have the plate and junk cluttering up the engine. ill make a video along with predator build In a few days

With the rod disconnected from governor lever and doing this setup, does the governor HAVE to be removed? I'm a DIY'er trying to learn so I'd appreciate the advise. Thanks

where can i find the small thattle linkage ? to connect between the cable and the Mounting gas?

i didn't actually take governor out of engine just tried to bypass it. like i said i know nothing about these motors. learning the hard way though

Putting a 6.5 powerfist in my pocket ATV 🤣🔥

Can a Kill switch malfunction from getting wet or just old and cause it to be stuck in off position, keeping the motor from cranking!

if you set up that linkage and remove the old one from the governor arm, can you just leave the governor gear in the engine?

very helpfull.

Can't get that throttle screw out at all any help and yes I've used crescent wrenches screwdrivers it's not coming out it's just ruining the screw

Nice

where do you get the spring for the govener

Life is too short for videos like this. #sausagefingers

Thanks man

Put prededtor in honda, wnna see top speed.

My predator does 35 with the governor

Well, I do know where you can find out. Go to "xxx oldminibikes xxx/forum". They can help you, but you'll have to be specific about what you did and pictures always help. Trust me, we'll get it running.

For a second I thought I had stumbled upon a diy child removal video. I find it very annoying they don't have a cable mount from the rear.

Check out my other video's

He doesnt know what he is talking about he said the idle screw adjust how fast you can go.

Very big jop

dont need to pull the crankshaft or camshaft to remove that arm and gov. gear just wasted time

COME ON THERE WAS NO NEED FOR THIS THROTTLE LINKAGE WHEN THERE IS A FACTORY ONE ON IT FROM THE START

Don't remove those springs, you could end up poking someone in the eye! /humor

Doing this will void your warranty, they are factory set for a reason people, if you want more power spend more money

please help...bought a predator 212 engine for go kart. when you start it, it us already at full throttle. the adjustment screw on carb only speeds it up. did i just get a bad 1? have you heard of this problem? thank you

Nice

please help...bought a predator 212 engine for go kart. when you start it, it us already at full throttle. the adjustment screw on carb only speeds it up. did i just get a bad 1? have you heard of this problem? than you