QUICK & EASY PLUMBING JOBS 

Turns out there's a lift there...🤣🤣🤣🤷‍♀️🤷‍♀️🤷‍♀️ ffs ey ! 🤟 Legend lad !

That mixer you changed Tom , I had a similar straight swap , slackened thd nuts off , pipes were stuck In so gave the mixer a tap to knock it off, one pipe came out and dropped down and fell out completely. Turned out it had a push fit elbow above the ceiling, when it dropped it came out . Problem was it was a plasterboard ceiling with no access. So a simple job cost me money getting the ceiling repaired . Keep plodding along.

I like these jobbing videos Tom, and they seem to suit you! Even if you find out there’s a lift!😂👍🏻

Nice one Tom, when you fast forward the speech sounds like the fish men off Stingray, the Gerry Anderson series from years ago (before your time no doubt) standby for action, any thing can happen in the next half hour, 😂 very apt👍

Nice little jobbing around vid, keep em coming Tom.

That scale you deal with is insane,glad I live oop north lol

Nice little jobbing around video Tom thanks as always

Great video as always Tom . I am an Electrician by trade have been for 44 years but love watching your vids have learned so much from them . Keep up the good work mate 👍🏼

Interesting jobbing day Tom, I’ve been changing 5 rads today for a neighbour, never short of friends when your a plumber, thing is I left the trade 29 years ago, but you never lose it, quite enjoyed it actually, take care Tom and have a great weekend 🚽👍

Keep them coming Tom, have a good weekend pal 👍🏻

Very nice day jobbing about there Tom .makes it exciting 👍👍

600000 tons of co2? Maybe this is when they realise 80% of engineers are not doing a gas rate. 😂😂

Hi Tom, a nice selection of jobs for you there, with not too much stress I hope. It’s great to see you on jobs that didn’t give you too much aggravation. Have a great weekend and as always take care Tom. 👍👍👍

Them values are the old opeller type used to have them on baths if you over tighten them the guts came out

on smart meters you select load when in service mode (press 0 4 times) and get an instant gas rate

Another good one Tom👍. You appear to be less stressed lately .jobbing about plumbing is doing you good. 😂😂😂

Nice wee selection of jobs in this one Tom, hope you have a peaceful weekend. 👏👏

Brilliant video Tom as usual 👍

Tom,when you are fast forward and talking you sound like a chipmunk,all ways watch the vids great stuff.🍺👍🇬🇧✅

Nice video Tom, with an interesting range of jobs.

Great video Tom 👍😎

Nice work mate 👍, what tool did you use to remove the olives on the mixer shower pipe work 🤔

Another good video Tom

Those valves in the near the end I think they might be pegker but they are total rubbish they always cease and then round off they tiny little slotted screw! Levers all the way bud! Another interesting vid mate good luck !

Thank god you put in lever valves. I hate those leaky screw valves. And quick question.... if a system kept switching on both heating and hot water when only one was selected, what do you reckon is the most likely culprit? Controller, valve or what? Cheers mate, always enjoy your videos :)

Careful, keep working so hard and you'll be rich like Elon Musk

I didn't know about the payment being paid back. Thanks for letting me know. It's a great video again, thanks.

Hi Tom, the shower valve you replaced at 11:09 could you tell me the make as I'm looking for the exact same thing. Thanks.

Great video again Tom , Im always trying to work out what you are saying in the speeded up bits but I dont speak Clingon!

Do you need any electrical qualifications for the electrics you disconnect/reconnect?

9:25 Thought Chaka Khan was gunna start playing!😅

Was it me mate or was that shower 90 bend almost flattened hahaha! Loving the vids

Did you work for a company who did comercial and domestic?

Do you get these jobs direct or through a 3rd party ?

I dont see why u absorbed the charge on ur first 2 installs tom, nobody could have foreseen, like airlines have the fuel surcharge in the small print, sometimes ur too honest for ur own good. These old proper ballofixs were far superior to what we havd now a 3mm allen key and would have turned no problem, still get them but price is rediculous

I like you and your channel but please try not to keep repeating yourself 🫢