Replacing Rear Brake Pads and Rotors on BMWs with Electric Parking Brakes

Подписаться 93 тыс.

Просмотров 708 тыс.

50% 1

BLOG ARTICLE: blog.bavauto.com/17160
"Like" us on Facebook - / bavarianautosport
"Follow" us on Twitter - / bavauto
"Subscribe" to us on RU-vid - / bavarianauto
Visit our online store - www.bavauto.com/
Call our Advisors at 800-535-2002
REPLACING REAR BRAKE PADS AND ROTORS ON BMWS WITH ELECTRIC PARKING BRAKE
Tools:
Mechanic’s gloves:
Universal OBD-II Fault Code & Diagnostic Tool with electric parking brake service function:
www.bavauto.com/fland.asp?part...
www.bavauto.com/fland.asp?part...
BavAuto socket, Torx and Allen bit set:
www.bavauto.com/fland.asp?part...
Caliper piston compressor tool:
www.bavauto.com/fland.asp?part...
15mm thin open end wrench (or BavAuto 16mm thin wrench):
www.bavauto.com/fland.asp?part...
Products:
Sta-Lube Disc Brake Caliper Grease:
www.bavauto.com/fland.asp?part...
New Replacement Brake Pads:
www.bavauto.com/se1.asp?dept_i...
New Brake wear sensor wire:
www.bavauto.com/se1.asp?dept_i...
You’ve likely seen our DIY video on replacing brake pads and rotors on a typical BMW or MINI (if not, watch it here; blog.bavauto.com/go/brakejob). The video shows how easy it is to replace the front and rear brake pads and rotors, without paying a shop a few hundred dollars. Since the video was published, BMW has introduced electric parking brake systems on many of the newer and current models. While the front brake renewal procedures have not changed, the procedures for replacing the rear pads is unique, due to the addition of the electric parking brake system. There are currently two different electric parking brake systems. The first generation system uses an electrical actuator that activates cables to standard drum-style parking brake assemblies. The second generation system uses electric actuators directly on the brake calipers.
Here are the links to our other brake service videos:
blog.bavauto.com/10012/bmw-bra...
blog.bavauto.com/11430/bmw-diy...
As noted above, the second generation electric parking brake system incorporates an electric motor driven caliper piston extender mechanism than mechanically extends the brake caliper piston to compress the pads against the brake rotor (as opposed to a separate small cable actuated drum brake assembly inside the brake rotor’s hub, or hat). Unlike a standard brake caliper, the piston cannot be simply pushed back into the caliper, using a piston compressor tool. According to BMW, the pistons must be retracted through use of the BMW factory scan/diagnostic tool. The tool is connected to the vehicle’s diagnostic port and then programmed to retract the pistons through the parking brake motor actuators. Once the parking brake piston extenders are retracted, the standard brake pad replacement can proceed.
So, you ask, do I have to take my vehicle to the BMW dealer for rear brake service? No.
As a DIY BMW owner, there are two options in servicing the rear brakes. We can use an aftermarket fault code and scan tool (availavle from BavAuto.com) or we can manually retract the actuators by performing a bit more work.
In this DIY video, we’ll show you how to circumvent the BMW parking brake retractor program and perform your rear brake service at home. Follow along as we perform the rear brake pad and rotor replacement on a 2010 535i (F10 chassis) with electric parking brake.
All products noted in this video can be purchased in our online store, www.bavauto.com/, 24 hours a day, 7 days a week. You are also welcome to e-mail us at info@bavauto.com or call into our headquarters and speak to our knowledgeable advisors at (800) 535-2002 (Mon.-Thurs. 8AM to 9PM EST, Fri. 8AM to 7PM EST, and Sat. 9AM to 4PM EST
www.BavAuto.com

Авто/Мото

Опубликовано:

28 янв 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 242

@pharmdiesel 5 лет назад

2014 BMW X3 rear pad and rotor change successfully completed. Extremely helpful in dealing with the e-brake system to compress the piston. Thank you!

@probey76227 4 года назад

And that's how you make a self help video, clear, concise and with just the right amount of detail. Thanks.

@user-bm6ks4bj7p 10 месяцев назад

Excellent video. Clear instruction and specific tool needed. I don't have experience to work with electric parking brakes. But now I'm sure I can replace the break pads. Thank you Bavarian Autosport.

@trevorritchie6840 7 лет назад

Thanks for this video. Just completed my first ever brake job & would never have even thought of trying if not for this video.

@SCWJackE Год назад

Good and clear step by step directions. What I notice about this and many other brake service vids; no one cleans the area first with Brake cleaner spray, and no one uses one or two drops of penetrating oil on bolts and nuts that have not moved since factory assembly, AND lastly, no anti-seize upon reassembly.

@bryanbaker1799 Год назад

This video is fantastic. Clear, concise, and great camera work.

@marcsmith3881 7 лет назад

Really nicely done. I didn't realize that you could just remove the actuator and it wouldn't cause any lights. I bought the tool and it has worked great on a VWs, Audis and a few Mercedes. I will try it on a 2011 750I soon enough.

@darylmiller2604 6 лет назад

Excellent tutorial. Thank you! You have earned my business in the future. Just a reminder to be sure the connector on the actuators are fully engaged. One of mine was very tight and didn't fully engage the first time. Needless to say, I got the dreaded “Parking brake malfunction”.

@fabiodarocha2842 Год назад

How do you activate the parking brake to reset the actuator?

@UnicornWithSprinkles Год назад

@@fabiodarocha2842 go in the car, pull the parking break switch

@Bamsebrakar2011 3 года назад

I have found it’s useful to loosen the brake disc (rotor) hub fastening bolt while the parking brake is still activated, to avoid rotating the disc. This is especially useful on the front discs (RWD cars). The disc fastening bolt is frequently stuck from rust).

@wladdobryakow6594 4 года назад

Благодарю вас уважаемый Мастер за подробное видию. Такие маленькие мелочи экономят нам большие деньги. Которые мы можем потратить на семейный бюджет. Filen dank Ser!!! Будьте здоровы!!!

@wlockwood 7 лет назад

Thank you this was very useful. And thanks for stocking the parts too.

@Neejay 8 лет назад

I really appreciate this, as I have a '11 535i, so this was literally the perfect video for this DIY.

@bavarianautosport 8 лет назад

+Neejay Glad to help! www.bavauto.com/shop.asp?HC1=0&Htarget=search.asp&HCY=2011&HCM=535i&SearchStr=rear%20brake

@jamesanderson84 4 года назад

Really high quality and precise video describing a potentially tricky job. Very useful. Great way to save $$$ vs. dealer service.

@dromaker 8 лет назад

best help EVER, thanks!

@dspguitar 4 года назад

Very informative and saved me a good chunk of time and money.

@74elitewolf 3 года назад

Tank you for posting this video Extremely helpful right to the point I save myself a lot of money thank you again

@darrensenerat8525 8 лет назад

brilliant video, I followed it and changed my rear brake pads discs and sensor on my f11 520d. thanks for your help

@malgorzatasenerat4419 8 лет назад

+Darren Senerat only thing missing is how to reset the computer so it restarts the mileage. But that is available on other videos

@cptsobczak 7 лет назад

Darren Senerat I wish they would provide torque values for all the bolts. They mention the Bentley manual but unfortunately it doesn't exist for the F10/11 body style

@RadoHudran Год назад

Did you have to turn the EPB the same way on both sides to retract it?

@michaelkroll5989 3 года назад

thank you for the video. i now feel much more comfortable to do this job thanks to the knowledge you have provided. never heard of an Actuator. Great job on the video and discriptions.

@claudea79 4 года назад

Thank you for this informative video! Well narrated!

@michaelluca9340 8 месяцев назад

Fantastic video, grateful for this one! This is very easy to follow.

@mrnatnatwarlal1972 9 месяцев назад

This is very good video showing clearly step by step procedure... Thank you!

@uffeponken 8 месяцев назад

Excellent and clear video. Just one more thing. When you compress the piston, keep an eye on the brake fluid vessel in the engine compartment. If it is filled up to high , it may overflow when brake fluid is pressed back to the vessel.

@TheManzoormd 5 месяцев назад

Yes thats the KEY and most important thing

@Pakosaladbar Год назад

2014 Bmw 528i changed with the information given.. great video

@ecanixgarage1106 3 года назад

Great video sir! For all you novice techs, the special skinny 15mm isnt absolutely necessary, ( normal 15mm will fit on most models), and you can compress the piston with your hand or a simple c clamp. Once again great video and to the point! This guy is good!

@umustdv81 Год назад

I hope you're right. Was hoping I didn't need the skinny 15mm. Doing my brakes at home tomorrow.

@kidgravity892 Год назад

@@umustdv81 No need for for the skinny 15mm, I have been using a flat head screwdriver in the slot (small opening) to prevent it from spinning (top for clockwise/bottom for counterclockwise) for decades. I didn't know there was a tool for it. 😅😅😅

@umustdv81 Год назад

@@kidgravity892 My wrench ended up fitting in there, but good to know a screw driver would work too. I can see that working.

@TheManzoormd 5 месяцев назад

@@kidgravity892 i would rather have the skinny guy

@richard1835 2 года назад

You can also use the ESB scan tool as well to retract the parking brake. Thank you. Great video

@Setright Год назад

He says that TWICE in the video 😊

@vitaliyk2822 7 лет назад

Thank you for the very informative video. Is it possible to cut down the original rotors to make them smooth just like in Japanese cars?

@danielson1989 7 лет назад

Very good tutorial - I'll be trying this on my F10.

@alfonsotejeda6931 7 лет назад

hi, congratulations, excelent and pro work and video. quick question; does the dongle elm327 v2 wifi universal scaner is able to clear the electric brake codes? kind regards

@Afghan-Pride-Till-I-Die 5 лет назад

Very nice job 👌 The only thing I would add is, when you are removing the caliper @ 3:40.. Just be careful when your moving the Caliper to access the Power operated parking brake Screws and system... You don't want to twist and put to much pressure on the brake line. YOU DON'T WANT TO RIP/CRACK OR DAMAGE IT!! 👍😊

@phillipjones5246 Год назад

brilliant well explained video, thanks and i appreciate your time and effort to post this video, i now have that new found confidence to tackle the e brake A+++

@emerycomputer 4 года назад

Great video. Thank you. Now I can finally attempt my 2007 e60

@dominicding7201 3 года назад

Your job is always right and I study it from you.

@kevkillevra 5 лет назад

Great video quick question, does this process apply to the 2009 F01 750li?

@jmart7827 3 года назад

Great video. after I release parking brake from inside the car should I unplug battery before pulling everything apart?

@_farkhadini_80 5 лет назад

спасибо за подробное видео вы очень помогли!респект!

@Passionate747 7 лет назад

Excellent installation , I have to install breaks on 2008 750li if weather is sunny I have purchased the parts. One of your video changing transmission fluid was good one too it saved me a lots of money, after changing the transmission fluid the car will go forward only in any gear but won't reverse it was overheating , The problem was cooler lines from the side of radiator the both lines were leaking fluid the rubber hose were not working . I went to dealer the cooler lines were $ 773.00 the installation was extra , I did explain the situation they said get cooler lines installed if the problem still didn't solve come back we will be glade to get you a new transmission for $7000. Wen I install the cooler lines I started the car it was working perfect but was jumping backwards and forwards but there were no signs with transmission wheel or overheating. your vides are very helpful thanks for posting them.

@TheManzoormd 5 месяцев назад

Thank you Sir for this amazing video, I have a question, do I have to turn the Brake button ON or keep it OFF before we start replacing pads and rotors.

@Charliesvue 4 года назад

Very professional job! Will use this as a tool when I do my breaks change.

@Bamsebrakar2011 3 года назад

Surely you mean brakes

@philipkearns8117 3 года назад

Really clear and concise. Thank you.

@lawrencechan6809 7 лет назад

I have a 2013 BMW (F30) 316i, do you have the torque specifications for the bolts?

@ceezauto213 3 года назад

Great video! Is this the same process for a 2012 bmw 528i?

@dimitardimitrov4637 4 года назад

Brilliant video, thanks for your help

@ikechukwuolisa7839 2 года назад

Excellent video. My BMW 640d has electric parking brake. However, your video does not show if you also need to release the parking brake from the control and if the ignition needs to stay on while doing the job to stop the parking brake coming on. Which is the case? Thanks

@souniquexyz 7 лет назад

I've done 50+ brake jobs in my life but this was the first with the electric parking brake on my BMW 550. The video really helped, thanks Bav Auto. Someone asked about whether or not they need to buy the piston compression tool. No. Most time you can use your two thumbs and slowly push the piston in. Sometimes you need to use one of the old brake pads, flip it so the pad side is on the piston, then compress gently from the back with a large channel lock (16" - 4" jaw) or a large C-clamp. One other note, when turning the electric brake center hole clockwise, understand it will take 30-40 quarter turns of a ratchet. It will finally stop. A handy tip is to have a jack stand under the caliper to support it while you prepare the pads and clips, it takes the strain off the brake hose.

@geoffreytodd Год назад

Hey thanks for making this video. a couple questions from when I was working on a 2018 X3 and ran into a couple issues. When retracting the parking brake, I got it all the way to the end stop, but the piston wouldnt retract in when using a c-clamp. I thought it might have been due to the parking brake not fully retracted so i tried rotating it fully counterclockwise, then clockwise again. When that happened, the torx bit on the caliper side was able to spin more and now doesnt hit an end stop. The piston also came out of the dust boot and I was leaking brake fluid ( I messed up somehow, trying to figure out exactly where or how). I ordered a new dust boot and plan to rebuild and bleed the system. My questions are, is the park brake destroyed to where I need to buy a new one or can i somehow tighten the nut on the threaded portion behind the piston to repair it? How can I get the piston to fully retract afterwards so I can get the pads in? Should I open up the bleeder valve to release some pressure in the system? This is the first BMW i've worked on. Other cars i've replaced pads and rotors for didnt have this kind of system.

@gottgaame 6 месяцев назад

U can just use a scan tool to retract the epb

@ab-ok6vq 6 месяцев назад

Thank you 👍very informative, simple DIY brake job...👍👍👍✌️

@Trailjunkie62 4 года назад

Very thorough informative video...thanks! I have a 2016 BMW X5M wonder if the electric park brake setup and procedure are the same as done here?

@paulblecharczyk7132 2 года назад

It is if you have push button operation of parking brake.

@jamesmcknight4146 7 лет назад

Most magnanimous vid...thankyou

@Policia1942 7 лет назад

Me gusto su video ya que hizo limpiesa y utilizo grasa mata ruidos Excelente video lo Felicito, asi es como se debe hacer todo tipo de trabajo mecanico.

@leonciorodriguezaguilera9513 3 года назад

Thanks a Lot Amigo, Excellent Helpful Video Tutorial...

@battlehrfred Год назад

TY Lovely video and great detail.. one QUESTION :: You Say @ 20:16 all we have to do is to activate the parking brake to reset the actuator and it is completed. after this actuator is reset, do you need to pump up the brakes "after" to seat the pads to the rotor or is pads already seated against the rotor after the actuator is activated?? ty for great video

@michael00751 8 лет назад

good video great help. thanks

@stevebodiford7858 6 лет назад

Is this process the same for a 2007 750Li..? Thank you

@NSK746 Год назад

Great video.just wondering if parking brake is applied while removing rotor or parking brake should be released. How do we do this you cannot put parking brake off unless switch ignition on or start the car. Please clear i am bit confused. Many Thanks

@autocarventuri 6 лет назад

show man!!! work like a charm!!!! Tks

@ht-infofacts2050 5 лет назад

Very Professional Job Done and a clear explanation ! However one more thing has not been covered here,about how to reset the brake service on dash bord after replacing the brakes ? Thanks .

@reggier2343 5 лет назад

I thought that if you replace the sensor you shouldnt get a brake service code. maybe im wrong.

@reggier2343 5 лет назад

are the thin rubber/latex gloves preferred to say mechanix wear gloves type?

@ajaiswal97 10 месяцев назад

Can you also post a video for 2019 BMW 740i front and rear break and rotor replacement ?

@knightrida6829 7 лет назад

awesome once again bav

@tugrulbey3095 3 года назад

Should i apply lubricant to o-ring while seating back the actuator motor?

@Dg-zj6jo 3 года назад

hi sir if you unplug on a gt bentley you get a fault code up do you have to have 12v connected as well please

@tensecondbuickgn Год назад

I'm doing a 2016 528i xdrive and am having a hell of a time trying to determine how to remove the rear rotor. Does that 12 point hub nut have to come off?

@Puchok777 4 года назад

Can i replace disc plate shield without removing hub? Can’t find any info in internet. Thanks

@omarhernandez4173 5 лет назад

thank you so much for all your help

@patricksmith5936 2 года назад

Before this procedure i,if its an automatic what do you select is it neutral ? With the handbrake off

@hardevgill2425 24 дня назад

thanks for your clear video for all detail.

@jonasgrumby1093 6 лет назад

Great video thank you for the help

@juniorsandoval6295 Год назад

could you not apply 12v directly to the motor to spin it rather than taking the actuator off? great video!

@kidgravity892 Год назад

Great video, all the right details non of the BS

@overlandersnorthwest 4 года назад

I followed all instructions and it was easy. But I didnt bleed it after the change and it seems to be fine. Not like a standard brake job I normally do. Did you bleed yours?

@HawgNSonsTV2 4 года назад

What size torques bits do I need for a 2016 BMW X3?

@rizla2000 2 года назад

Classy video. Very informative

@fast4d1 5 лет назад

You guys are awesome!

@xxfreshprincexx1 Год назад

What kit do you guys recommend for a 2011 535i .. trynna save on labor by grabbing the parts

@jeremyjones743 7 лет назад

Hey does this video method work on 2013 528i (F10)

@stevebodiford7858 6 лет назад

Is there just one sensor on the right rear? And does it need to be replaced when replacing rear pads on both sides...?

@talaatuehai1049 7 лет назад

Good video ,,, Bleed breaks or open master or not neccerary ????

@77chatham 3 года назад

Would this be same procedure on a 2017 BMW M6 coupe?

@45bogdan 3 года назад

Hi I did same way breaks pads after this my break pedal is sponge all the way down. Any suggestions?

@frank070808 3 года назад

do I need manual just electronic parking brake twice if I want to change real brake pad on 2012 BMW 528i xdrive

@gbravo86 3 года назад

well made video informative and good quality

@raul4295 4 года назад

I really miss this videos

@mvolpe003 2 года назад

Followed this procedure to replace the rear brakes on my 2017 BMW M6. Reset the Rear Brake Pad light no problem. Now I have Parking Brake Malfunction light on. Any idea on how to fix?

@xr3703 4 года назад

Will this DIY work for a 2014 BMW 528i?

@knopfrob 4 года назад

Do you still have to blleed the brakes ? Or is it different then a regular car.

@Munecoshh1 2 месяца назад

Awesome video, so the parking break you don’t do anything special with it? You just take it off put it back?

@daveblack9105 2 месяца назад

Great video. Thanks!

@luckyjerk2890 7 лет назад

First off great video. Very informative and produced with great quality! I know this would be out be out of the "Brand of BMW" however I would love your input.My wife has a 2014 Audi A4 and she as well has an electronic parking break in the rear.Would the same steps apply to retracting the piston for the rear Audi caliper?

@paulblecharczyk7132 2 года назад

I believe it is very similar.

@ServiceDesk-km1jf 2 месяца назад

Just followed your video to do the rear brakes on an M5, thanks.

@RobertHa81 3 года назад

Hi! Thank you for your video. For the rear brakes, should the emergency electronic brakes are engaged or disengaged? Does it matter?

@paulblecharczyk7132 2 года назад

Disengaged as in released.

@simiongligor4500 7 лет назад

Buen trabajo!!!!

@Carlitos283 3 года назад

Best video ever!!!

@danieldoyle3138 2 года назад

Anyone know what size the torx screws being used are?

@AL-rq4qs Год назад

how do you turn off brake light on the dash after doing the brakes? thanks

@pgtips7818 4 года назад

Hi what make discs did you put on ?

@thecargeek7090 3 года назад

thank you so much for this video

@swampusmaximus 5 дней назад

Fab Video, Many Thanks :)

@joesnowmobiles 2 года назад

Since the front of that piston is notched could you just rotate with the proper brake compressing tool while turning clockwise instead of removing the whole electric parking brake motor?

@adrianarias266 5 лет назад

What size is torx bolt to depress e brake

@MaxSandberg 3 года назад

Thanks for posting

@CondorrK 4 месяца назад

See the last 2 vids mentioned that you cannot perform this job without a tool that will release the PB to the out condition. Then told us the tool is cheap 😂 Glad i found this video