Spray Gun Problems and Their Solutions 

Haha! What are the odds, I go on RU-vid, grab the first video on spray gun problems, and the first thing you illustrate is my exact issue! Thanks for the vid I needed!

Best video I have found on gun issues. Thanks for taking the time to make it

Thank you so much for your video, it fixed my issue straight away! no more fluttering. I only had it hand tight after first using my gun and the clean up, thanks mate.

Thanks for this. Sorted out my pulsing spray problem.

October 2022 and this video is still helpful. Thank you 👍🏽

Thank you so much!!! My gun was pulsing. I haven’t tried yet but I am praying that this will resolve the issue!! Goddamn urethane paint so expensive! I was praying there was an online video so that I didn’t have to spend hours and hours trying to figure it out on my own!

You bloody beauty. She was pulsing, you solved my problem. Good onya Mate

Great video my dude!! Just awesome thank you so much, even went in detail about fixes. Your the man!

Great info. Thank you a thousand times over.

He touched on some series points (awesome)!!!!! Keep up the the good work

Man this was helpful I was about to junk this clear gun.....Thank You

Thank you ! Got me up and going again !

Thanks for the tips.

Excellent advice thanks.

This helped me a lot today. Thanks.

So helpful thanks mate!

Great tips brother , helped me out

Problems solved! 2 thumbs up 👍

Thank youvery much, this is very helpful 😊

I was just spraying paint with a Sanborne siphon gun and went to clean it out for clear coat, now I have no flow. What causes that?

What about when you have dead spots/no paint within a wide fan pattern ?

Honestly thank you.

Excellent, thanks

Do you have a fix for air coming out of the gun with out squeezing the trigger? And once the trigger is squeezed it stops the air flow??

Good video thank you

I've had a really really annoying weird problem, where the paint would come out in big blobs instead of a nice mist like expected. I've tried everything - air pressure lower/higher, fan adjustment tighter/bigger, adding thinner etc. but nothing would solve it. In the end, the small holes in the air cap on either side of the nozzle were plugged with old paint. After soaking in thinner and blowing out with 6 bars of compressed air, it works like a charm again. This wasn't mentioned in any of the troubleshooting videos, probably because it's so easy? So I'm leaving this here for others who might have the same problem... TL;DR when the gun doesn't work like it's supposed to, first thing is to really really clean it well including all the small holes.

Very informative

Thank you for sharing valuable information. I have a SATA 5500, used to make spray outs only at the moment ( not a painter yet, still in training). Since yesterday, it started something strange : with the trigger half way on, jut to blow air to dry the card, the air is going in to the paint cup ( 3M single use ), literally inflating the cup like a balloon. What can it be the cause of this issue?

Thank you so much help a lot 🎉

I have a lvlp gun that has a stream of paint when I take my finger off the trigger. If I tighten the screw at the nozzle all the way right it doesn’t drip but I get a very small spray pattern.

The hvlp gun I have that looks like this one wasn’t picking up enough paint but the vent tube was plugged and I realized something was wrong cause you unhook air hose and gun still has pressure enough to squirt out paint . Vent pipe at the 90 elbows was plugged I cleaned them will try again tomorrow

Hey I got one what if my paints itamizing in siphon tube before it reaches the tip clogging the tube?

My gun sprais droplets instead of fog... what causes that? I noticed airbubles in container also.

I’m having an issue where I pull the trigger and there’s no air prime before the paint. It’s on a conventional 5 gallon pot at 50 psi, binks 2100

thank you ...

Great video, thank you. Still I have strange problem not covered here: My Sagola paint gun worked well until one day just started to blow air into paint dish instead suckin it. Can anyone advise please? (Detail cleaning with dissasembling and assembling was already done). I can't figure out what is wrong.

im korea painter . The tip to control paint amount is broken. this is my devilbiss luna. i think the screw line is worn out a little. please tells me how to repair this problem?

What if the nozzle is tight and it still stutter?

Tightened nozzle, stutter/sputter gone. Thank you!

Very good

How I solve Leak from back side of nozzle?

My gun requires not to exceed 50 psi. I have my compressor set anywhere from 30 - 50 and I get nowhere the same air pressure that you are getting out of your gun. Could possibly my gauge be off?

Nice

Quick Morty, get the spray gun!

Why is mine building up paint at the tip of the gun? Is it too much air? Is the fan too wide? I can’t ever get a good spray with these guns. Are you not supposed to use oil based paint with these? Everything I paint looks bad bc I can’t get a good spray. This video was helpful in other cases, but not with what I need. If my question could be answered that would be great

What is the problem when the gun does not pickup any paint or thinner in cup??

What about from the paint tube in the bottom that feeds the paint is not spraying all the way barely getting paint out of it and it's a bottom feed paint gun not an expensive one

Y en español cuando o dónde lo puedo ver

mine has a problem , i hook it up to air and theres air hissing out the tip without touching the trigger.

How does a gun like this stack up to modern guns like the HF black widow?

Sata minijet. No air at the cap. Does not atomize fluid. Has me stumped. Cleaned it can't figure out

Great video! Thanks!

What if it won't spray at all

Thank you! I was about to throw this sprayer in the trash!

What should I do when there is no material flowing? I only get air instead.

Bang on mate cheers 🖐this spray gun has has been driving me fuckin nuts👌😎👍

my tip keep clogging?????

great content listened to content but couldn't watch the video as the blurred picture drove me mad.

My spray gun is blowing air but no paint coming out

"So if you have a plug in the cap, that''ll do that ... so we fixed that ..." Umm, I was hoping you'd show how you fixed it.

I'll give you a pass on the audio quality because you got my gun working again in like 5 minutes.

Dalle foto sembra eccezionale ma ci vorrebbe una prova pratica

Get closer to the mic. Cannot hear.

Hello

The reason your gun is spraying to the right is because there’s a piece of duct tape stuck to it. You’re welcome. Seriously though, this is a helpful video, thanks!

Air flow 10%....no section 0%

Not spreying not...spill

Stop talking while spraying, can’t hear you.