Тёмный

Troy-Bilt Pressure Washer No Start: Complete Maintenance 

The Lawnmower Lady
Подписаться 21 тыс.
Просмотров 22 тыс.
50% 1

Easy diagnosis of a Troy-Bilt non-starter with no special tools. Complete routine maintenance for a pressure washer with Briggs & Stratton Quantum engine. Although the owner used the washer regularly and drained the fuel every winter, without regular upkeep, small issues become bigger problems. Full service including engine oil change, carburetor service, air filter, new o-rings, and this machine runs like new.
Briggs and Stratton air filter no. 491588S : amzn.to/3qpJSOh
Tecumseh carb tool no. 670377 : amzn.to/3NbmVXQ
Briggs carburetor overhaul kit no. 498260 : amzn.to/3OPNaVb
Briggs air filter no. 491588S : amzn.to/3P39t9M
Champion RJ19LM : amzn.to/42opb2k
Briggs SAE30 small engine oil: amzn.to/43Js6nh
Briggs O-ring kit : amzn.to/3oKfayX
Inlet screen kit (generic) : amzn.to/3oEfNdr
Briggs & Stratton Synthetic Pressure Washer Pump Oil - 5.3 oz no. 190585GS : amzn.to/45KYiZr
00:00 I'm not Ken
00:07 Easy diagnosis for no start engine
03:57 Oil level check
05:13 Remove air box
05:45 Drain stale fuel and flush tank
07:22 Remove carburetor
09:53 Disassemble carburetor
12:53 Ultrasonic bath
15:22 Reassemble carburetor
20:50 Replace carburetor and air box
24:11 Torque headbolts to spec
25:57 Spark plug check
26:42 Drain oil from crankcase
27:20 Replace worn O-rings for wand
34:23 Replace engine oil
35:39 Replace water inlet screen
35:05 Test run with water
The tools I like and use most often:
Magnetic spark plug socket set: .to/3CzmpvO
Tachometer: amzn.to/3sHibiH
Vessel Megadora JIS screwdriver set: amzn.to/363RFqO
Channellock Bent Needle-nose pliers: amzn.to/3I5DbnA
Long 1/4 Quick-connect Torx Driver Bits: amzn.to/3HUNgnm
Spark Tester: amzn.to/3CxW2qi
OTC Leak-down Test Kit: amzn.to/3CyUhJn
Compression Tester: amzn.to/3IWd6sp
Wear your safety glasses, or you'll shoot your eye out. Try on some gloves. Take off that spark plug boot. Clean your room. Open the windows, those fumes are nasty. Just 'cause I do it, don't think it's the end all, be all solution. There's plenty more ideas out there, I can't take responsibility if you slice off a few fingers after watching my videos. And don't just pour that toxic stuff down the sewer or in the ditch, dispose of waste responsibly. Just be safe, OK?
Follow along with me elsewhere:
/ thelawnmowerlady
the-lawnmower-lady.blogspot.com/
Titles, opening graphics, and music by AbleVFX.
Any links to products are likely affiliate links, and I may earn a small commission from qualifying purchases (Thank You!), with no additional costs to you.
Disclaimer: The content of this video is purely for my entertainment, and is available to you for informational and educational purposes only. It's not substitute advice from small engine mechanics with professional training and certifications, nor does it create any kind of relationship between the The Lawnmower Lady and you. Your situation may be different, and the The Lawnmower Lady makes no warranties, express or implied, as to the fit, accuracy, or applicability of the information shown in this video, and implies no guarantee of results. The Lawnmower Lady and any sponsors of this video are not liable for any damages of personal injury, property damage or loss of any kind that may result from the use or reliance on this video and/or any parts and procedures represented in this video. You are using the information presented in this video solely at your own risk.
#pressurewasher #smallenginerepair #DIY

Опубликовано:

 

25 июл 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 141   
@TheLawnmowerLady
@TheLawnmowerLady Год назад
If this video helped you, please consider clicking on the THANK$ button above 🙌Watch this video next if your washer has a Honda engine: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-b7lffKGZZsE.html
@Redtash1
@Redtash1 Год назад
You forgot compression. 😁😁😁
@TheLawnmowerLady
@TheLawnmowerLady Год назад
@@Redtash1 I respectfully disagree. Compression is a subset of air. No air, no compression. So there.
@Redtash1
@Redtash1 Год назад
@@TheLawnmowerLady What do you mean compression is a subset of air?
@TheLawnmowerLady
@TheLawnmowerLady Год назад
@@Redtash1 You can't have compression if you don't have air. Air comes first, it's primary. Like saying, Oh! Your forgot about timing. No, timing is a subset of spark. No spark, timing is not that germane to the diagnosis.
@Redtash1
@Redtash1 Год назад
@@TheLawnmowerLady True but you can have air without compression. 4 things are needed in the cylinder all at the same time or the engine won't start and run. Air, fuel, spark and compression, if any 1 of the 4 is missing the engine won't start and run. In the 4 stroke engine what are the names of each of the 4 strokes and what is occurring during each stroke?
@INSIDEHOUSEGARAGE
@INSIDEHOUSEGARAGE Год назад
I actually like the feature that it lightly sprays when not in use, keeps the pump cool and lasts longer. very good video!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks! I'm still not sure if it's a bug, or a feature. I did download the manual, and no mention of holding the trigger open while starting. My washer, (an old Craftsman with a Pulsa-Prime carburetor from 2005) the OM is the same.
@beakittelscherz5419
@beakittelscherz5419 Год назад
That's sort of the maintenance everyone wishes to get when bringing in their Units... Very well explained and step by step. Enjoyed it
@TheLawnmowerLady
@TheLawnmowerLady Год назад
It often seems more complicated than it is. I try to show that most tasks can be completed with common tools and common sense. Thanks for watching!
@tonym6920
@tonym6920 Год назад
Thanks for the interesting vid! Regular maintenance, as you said, is key. Treat your equipment casually and it will end up a casualty. Have a great week! 👍👍
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I agree! Thanks for watching. Cheers!
@RaysLaughsAndLyrics
@RaysLaughsAndLyrics Год назад
Nice to see the Ultrasonic finally thawed out. Great vid to workout most Press Wash issues. Thanks 4 posting.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
You bet Mr Ray! Thanks for watching. Cheers!
@philliphall5198
@philliphall5198 Год назад
It’s 98 in West Texas today and I laugh when you said that, bet she is burning up today
@TLMD
@TLMD Год назад
Way to go Stella! Another great fix and an even better video. Keep up the awesome work!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thank you Sgt. Cheers!
@woodwind1335
@woodwind1335 Месяц назад
Wellll finally I found you! I love your clear methodical style and good information. I have had my arsenal of mowing yard Maint gear preserviced as usual this year. All four pieces of equipment have failed to run…after returns to two different shops, for different reasons and one was way overfilled with oil (why? Dunno) I am now assigned as my mechanic!🤣 I have sorted out multiple issues already…my zero turn supposedly needed a new solenoid, it turned out to be dirty contacts at the harness connectors, my push small self propelled mower would not start after three returns to the shop, both are now repaired and run like a champ with your help. my pressure washer just serviced will not crank after a recent service I am now in this one…and this is from two different shops🤣🤣Looking at the carbs I realized that most were not cleaned and two had damaged gaskets or seals 😳😂 I have a large piece of property, and yearly I have all my gear serviced pre season, pay attention to my fuel (stabilize) and check for water… Well I am setting up as I go now to have the parts and tools to do these service and repairs myself. I will even buy an ultrasonic cleaner…way cheaper than to pay for the services. And fun, somehow I like doing this, it is meditative. I have always four small engine tinkering fun. Thanks for your channel it is a game changer. Another new “Girl” mechanic here! Cheers!
@TheLawnmowerLady
@TheLawnmowerLady Месяц назад
I'm so very happy to help! I appreciate you watching. Cheers!
@523Metube
@523Metube Месяц назад
Fantastic video, with lots of info, clearly presented & described, at a great pace. You go girl !!
@TheLawnmowerLady
@TheLawnmowerLady Месяц назад
Glad it was helpful! Cheers!
@thomasroche164
@thomasroche164 Год назад
I like the bread tie trick with the float!! Thanks. Enjoy your videos..
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Glad you like them!
@jimbrewer2893
@jimbrewer2893 Год назад
Preventive maintenance done correctly. I use some shop air to blow the needle seat out. Works most times. A little Vaseline on the o rings helps seat them. Good video Stella.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Great point!
@whip-its_dad4239
@whip-its_dad4239 Год назад
Good job , your videos are very thorough .Thank you .
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Cheers! I appreciate you watching.
@martinburgess4814
@martinburgess4814 Год назад
Great to see you posting videos Stlla all the best take care.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks, you too!
@andersforrad
@andersforrad Год назад
Nice one Stella! Great work as always 👍
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thank you Anders! 😃
@garyclifton2180
@garyclifton2180 Год назад
Great informative video Stella loved it x
@TheLawnmowerLady
@TheLawnmowerLady Год назад
G-day Gary! Thanks for watching. Cheers!
@barryewalt3250
@barryewalt3250 Год назад
Great work Stella
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thank you so much 😀
@haneyoakie14
@haneyoakie14 Год назад
Quantum! My favorite!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
It's pretty bullet-proof IMHO.
@tinkeringtaylor3053
@tinkeringtaylor3053 Год назад
excellent video Stella, and some really good information well done 👍
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thank you Nev!
@LifeNTheSlowLane
@LifeNTheSlowLane 5 месяцев назад
This was awesome. Love the content.
@TheLawnmowerLady
@TheLawnmowerLady 5 месяцев назад
Glad to hear it! I appreciate you watching. Cheers!
@NarrowPathOfLife
@NarrowPathOfLife 11 месяцев назад
Great video very informative & thorough! 👍🏽
@TheLawnmowerLady
@TheLawnmowerLady 11 месяцев назад
Glad you enjoyed it!
@mario73otw42
@mario73otw42 Год назад
Thanks watching your video helped me fix my granddad old pressure washer 👍
@TheLawnmowerLady
@TheLawnmowerLady Год назад
That's great! I appreciate you watching!
@dLLund
@dLLund Год назад
ms LL - thank you for posting, yet again - dLL
@toddosterhout9866
@toddosterhout9866 Год назад
Spark, fuel and air are necessary but don’t forget compression! Love your channel!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Great point! To be fair, compression is a subsidiary of air, so I don't consider it one of the holy trinity. :) Thanks for watching. Cheers!
@mrbubetube
@mrbubetube Год назад
ya compression should be there too. several times I've seen people baffled when their engine wouldn't start even though it had spark fuel and air. Turned out the problem was a loose head bolt on the engine. and that's especially true for string trimmer engines. if you have a loose head bolt on a trimmer engine, you'll NEVER get it started. I've seen several good trimmers thrown in the trash and all it needed was a head bolt tightened down hahahahahahaha.
@rubeng3091
@rubeng3091 6 месяцев назад
Awesome job!
@TheLawnmowerLady
@TheLawnmowerLady 6 месяцев назад
Thank you! Cheers!
@freddyrivera4970
@freddyrivera4970 7 месяцев назад
Maam thankyou very much, that is the exact same machine I had the very same problems and again many thanks I got it working following your step by step guidance ❤
@TheLawnmowerLady
@TheLawnmowerLady 7 месяцев назад
Very glad I could help. Cheers!
@chrisssmallengines7163
@chrisssmallengines7163 Год назад
I call this method Prime for a Good time . The quickest assessment method that use can use .
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Indeed it is!
@yves-mariesellin6026
@yves-mariesellin6026 Год назад
Encore une vidéo intéressante 🙏💪
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Merci! J'apprécie vraiment que vous regardiez.
@todd8155
@todd8155 2 месяца назад
Nice video, good clear instructions! Several points: 1) Many starter fluids have an upper cylinder lubricant, although I don't know how much or how well they work. 2) Gasoline is highly flammable and is dangerous to use as a cleaning solvent so be careful! NO SPARKS and only use outside. One can spray the outside with carb cleaner in a spray can to keep the volume of fluid down. Alternatively, one can get gallon size containers of carburetor dip such as Berryman Chem-Dip. Not the cheapest, but only slightly flammable, and don't need an agitator. None of these chemicals are good to get on your skin...
@TheLawnmowerLady
@TheLawnmowerLady Месяц назад
Thanks for watching.
@hydrocrab74
@hydrocrab74 Год назад
Great videos you have.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I appreciate that!
@hydrocrab74
@hydrocrab74 Год назад
@@TheLawnmowerLady 😁
@biggaspirit1
@biggaspirit1 Год назад
Good video, thanks.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Glad you liked it!
@petefroud5308
@petefroud5308 Год назад
Good job Miss Steller.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Cheers Mr Pete! I appreciate you watching!
@jonsvenavena2901
@jonsvenavena2901 5 месяцев назад
Excellent!!!thanks, J
@TheLawnmowerLady
@TheLawnmowerLady 5 месяцев назад
You bet!
@RichsMowersNBlowers
@RichsMowersNBlowers Год назад
Wait ✋ I think Ken is the lawn Mower Lady Pshhhh. At least he played the LML on YT.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Haha!
@charlieg424
@charlieg424 Год назад
Love your vids. Where can I find that carb overhaul "master kit"? Keep them coming.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Check the links in the description. Thanks for watching!
@kevinvincent1963
@kevinvincent1963 4 месяца назад
Thanks, your very detailed,I like you a lot
@TheLawnmowerLady
@TheLawnmowerLady 4 месяца назад
I appreciate you watching. Cheers!
@waynestefinashen239
@waynestefinashen239 Год назад
Well done Stella yep Jake actually needed to use our surveillance video to see where our yellow tip flew off to when we used our pressure washer the last time. A little corrosion and i did not get the tip seated properly in the disconnect. Have never seen that type of leakage on a pressure washer wand but makes it easier to start eh?
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks Wayne! It does make it easier to start. I did look at the OM, and no mention even of pulling the trigger while starting, to reduce back pressure. It's still a mystery to me. I appreciate you watching!
@waynestefinashen239
@waynestefinashen239 Год назад
@@TheLawnmowerLady Yeah manuals are apparently different for many pressure washers especially when you want to know how long you can run the machine without engagement of the wand handle to prevent damage from the water overheating. The big issue is if the thermal relief valve is working or not but with your wand by passing the water like that it should never be an issue. Maybe they should make them all like that and they would all last longer eh!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I agree! Except for the part where the wand flips around like a snake for a second or two before the pressure builds up enough to close that valve. I got very wet making this video, LOL!
@TecumsehRulesbcserk
@TecumsehRulesbcserk Год назад
One of the worst looking carburetors I’ve replaced was on a Troy Bilt Storm 2620 snow thrower. The entire thing was filled with bright blue colored rust, the needle was so corroded that it wouldn’t even come out of the seat, and the throttle flap was completely seized up. I still have it sitting in my tool box to prove how bad it is to let old gas and water sit in there for several years.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I too have a show-n-tell box of bits and bobs for customers to see the worst of the worse. I appreciate you watching. Cheers!
@tonywampler217
@tonywampler217 10 месяцев назад
Very very good 👍😊
@TheLawnmowerLady
@TheLawnmowerLady 10 месяцев назад
Thank you! Cheers!
@haneyoakie14
@haneyoakie14 Год назад
Not Ken? Lol. No Duchess for you!
@haneyoakie14
@haneyoakie14 Год назад
14:10 Pine Sol? I use Dollar Tree Pine Sol knock off cleaner. It’s so cheap I can dump it after use and next time use fresh with hot water out of my basement stationary tub faucet and it is already at 55 degrees C. Saves 20 minutes vs heating from 17C basement temperature, which I think is about 62F.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I haven't noticed that in my dollar and a quarter store. The difference between you and me, is I turn on the machine to let it warm up, then get distracted, and maybe get back to it, several hours later. It's always heated and ready. LOL
@Rein_Ciarfella
@Rein_Ciarfella Год назад
I have plain water in mine and use containers with cleaning solution for the parts. Prior to dropping the parts into the containers I nuke the containers full of solution 3 minutes, then drop in the parts, secure the lid and place in ultrasonic. No waiting to heat up. No wasted time or electricity. 🔧👍
@sherriegordon4539
@sherriegordon4539 Год назад
Hi..I really enjoyed your video. DEFINITELY learned a lot from watching you. Where do you order your parts in the cases. I looked up the item number on Amazon..I couldn't get a case of carb parts. I've started working on my own mowers and pressure washer. Very interesting.. challenging 😅
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks for watching! I shop around at major parts houses (partstree, jackssmallengine, etc.) They usually have rebuild kits.
@Pete.Ty1
@Pete.Ty1 Год назад
👍👍👍Thank you
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thank you too
@philliphall5198
@philliphall5198 Год назад
Those screens are very very important and we should flush hose before connecting to pump every time to keep buggs and trash out
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I agree!
@scottbryant2235
@scottbryant2235 Год назад
Great video, but I want point out what you said about your 2stroke squirt used on either. It needs lubrication. Well, that's what the pump needs on a pressure washer. Those plastic cages and rubber seals need lube and that is what water is. You ran it about 500 revs dry. Hook a hose up for 20 seconds first to wet 'em down.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Interesting, but my math says 50 revs for 2 seconds running at 3000 RPM. Thanks for watching.
@supermeelu
@supermeelu 2 месяца назад
Thanks
@TheLawnmowerLady
@TheLawnmowerLady 2 месяца назад
Happy to help!
@williamodom2580
@williamodom2580 Год назад
I have the same TB Pressure washer, when I stored it for the winter it was running fine took the unit out this spring and the engine was locked up? took the unit in for service and we found the flywheel wheel was cracked?? we can’t figure out how the flywheel cracked over the winter, purchased and installed a new flywheel and unit started right up
@TheLawnmowerLady
@TheLawnmowerLady Год назад
That's crazy! Backfired by chance? Thanks for watching!
@Rein_Ciarfella
@Rein_Ciarfella Год назад
Stella, I'm in the market for a magnetic drill hex adapter. I see you using two different ones, a red one for your impact at 5:12 and a blue one for your drill at 23:30. Can you tell me if those are any good, if they are magnetic or have a spring release (requiring a bit more effort to release each time) and how they actually are connected to your two cordless tools. I'm also curious about the actual socket you are using because it almost looks like it has a short piece of hex stock glued into it. Is that correct? Thanks for your time!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks Rein- Those I'm using are cheap HF holders as I killed all the shorter ones in this set: amzn.to/42vGzCs Those were, and are the best IMO, but after 8 years of impact driver use ( I don't suspect they are impact rated) the spring indents to hold the bits fell out and the release springs gave up. They were very easy to use at the release collar ejected the bit easily. I still have all the very long ones, in perfect condition. The sockets themselves are just inexpensive (Klutch or Dewalt) 1/4 quick connect nut driver sets: amzn.to/43yTGUP They usually are impact rated. You might notice (or you will from now on) I paint the metric ones with an orange ring of fingernail polish and the SAE are just black. Thanks for watching. Cheers!
@VintageEngineRepairs
@VintageEngineRepairs Год назад
Great video! Interesting feature of the water continuously leaving the hose when the engine is off. Did you figure out why?
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks Tom! The best I can figure is it is meant to work this way? It is a larger gun/wand than mine. My guess it's meant to ease the fumbling of holding the trigger open whilst start a higher pressure machine? Maybe a different spring mechanism behind the ball valve to prevent it from holding trigger pressure without the pump pushing fluid? Now I'm gonna have to go look up the OM. LOL!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Interesting, the OM for this unit says nothing about holding the trigger on the wand open whilst starting. Looking up the OM for mine, (2005 Craftsman version with Briggs Pulsa Prime engine) doesn't mention it either??? Who knows?
@VintageEngineRepairs
@VintageEngineRepairs Год назад
@@TheLawnmowerLady yep, you’re probably spot on, to purge the air so the pump doesn’t run on any air in the line and you don’t have to hold it. :)
@user-ct2qq5mx6g
@user-ct2qq5mx6g Год назад
When using your Ultrasonic cleaner, do you also use the heat, and at what temperature?
@TheLawnmowerLady
@TheLawnmowerLady Год назад
I have it set on 50C
@ronnieso
@ronnieso Год назад
Will these pressure washer motors work on Self-Propelled mowers without much problems?? Thanks in advance.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Hard to say, the key is the crank shaft on the power side. Lots of variables for length, and diameter. Thanks for watching!
@user-di8wh9fz1m
@user-di8wh9fz1m Год назад
my self , i all ways take off the gas tank and flush it a completely , clean all the orifices in the carburetor and put a gas filter in the line , and a new needle and seat , this way the customer will have a long service out of the machine . I recommend to the customer to use a gas filter on the gas nozzle of the gas container when filling it , And to use Sta-bil gas additive if stored over the winter or a long period of time . A ounce of provention .and i replace the fuel line if the machine is older than a year . i Have see them fall apart in side and contaminate the fuel system . and to i let the custom know to run the machine until it runs out of gas and close the choke for the winter . Hope this helps all of you . Have fun doing mechanic work
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Good ideas! Thanks for watching.
@genemyersmyers6710
@genemyersmyers6710 3 месяца назад
Is the needle valve aluminum ?
@TheLawnmowerLady
@TheLawnmowerLady 3 месяца назад
As I recall, yes. Thanks for watching.
@philliphall5198
@philliphall5198 11 месяцев назад
I dip my hose ends in use motor oil and brake spray before I use them Keep rust away
@TheLawnmowerLady
@TheLawnmowerLady 11 месяцев назад
Good tip! I also have started using silicone grease, thinking O-rings might swell up.
@Rein_Ciarfella
@Rein_Ciarfella Год назад
Stella, I respectfully beg to differ with your very first sentence. The old “three things to start/run” is incorrect because it leaves out two more essentials. To really diagnose issues all five requirements should be running through the mechanic’s mind at all times. FACTS - Fuel, Air, Compression, Timing, Spark!!!
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Thanks Rein. From 30,000ft, I see compression as a subset of air, and timing as a function of spark. That's my story and I'm sticking to it. :)
@Rein_Ciarfella
@Rein_Ciarfella Год назад
@@TheLawnmowerLady Sure, that’s one way to look at it. I’m speaking on behalf of us newbies who watch these videos to learn. Having something easy to remember like FACTS helps us a lot.
@robertmailhos8159
@robertmailhos8159 Год назад
The spray tip flying out of the wand is a pain in the back side I've been there did that 😡🤬
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Yep, been there, done that. Way too many times. LOL
@robertmailhos8159
@robertmailhos8159 Год назад
@@TheLawnmowerLady that is the truth about that matter young lady 💐🌹
@_bubblezzzzzz_
@_bubblezzzzzz_ 9 месяцев назад
Is this why I can't find the oil drain plug on mine, you are to tip it? I have one that has been sitting for 3 years and I need to change the oil and I can't find information anywhere. THE MANUAL says to change but doesn't give an accurate picture of the drain plug.
@TheLawnmowerLady
@TheLawnmowerLady 9 месяцев назад
Depending on the engine, yes, you might need to tip it over. The manuals often don't reflect the different engine needs correctly, as the washer manufacturer can put engines from different manufacturers on the same model. You can try a length of tubing to siphon the oil out.
@_bubblezzzzzz_
@_bubblezzzzzz_ 9 месяцев назад
thanks for the quick reply. I just changed it but I will probably siphon it next time if I let it go that long. BTW there wasn't any gas in the gas tank so I didn't have to worry about that leaking out, thankfully.@@TheLawnmowerLady
@KensSmallEngineRepair
@KensSmallEngineRepair Год назад
Honestly, you DO do a good Ken! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-rDPvkR4oGxg.html 17:13
@TheLawnmowerLady
@TheLawnmowerLady Год назад
LOL!!!!
@gadasavideos8564
@gadasavideos8564 Год назад
Air and fuel won't be enough unless you compress them.
@TheLawnmowerLady
@TheLawnmowerLady Год назад
That's getting the cart before the horse. Compressing fuel without air won't combust, nor will compressing air without fuel. That's my story and I'm sticking to it :)
@thepoopsoup
@thepoopsoup Год назад
Gum out will remove gasket materials
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Great idea! I never thought of that. Thanks for watching. Cheers!
@williamclements273
@williamclements273 10 месяцев назад
No way that float was parallel with the carburetor body; close enough probably works though.
@TheLawnmowerLady
@TheLawnmowerLady 10 месяцев назад
Thanks for watching.
@haneyoakie14
@haneyoakie14 Год назад
29:15 just use the tools God gave ya?
@philliphall5198
@philliphall5198 Год назад
Might want to remind everyone of timing, since cams are plastic now and gears
@TheLawnmowerLady
@TheLawnmowerLady Год назад
Not sure if they had switched over to the plastic cam shaft lobes on this engine, but that's a fair point. Thanks for watching.
@themowerman
@themowerman Год назад
Hell no.. your not ken.. you're much better looking..
@1244taylor
@1244taylor 10 месяцев назад
The person who owns this PW should NOT have a PW as he has not done anything to this unit to keep it working well..
@TheLawnmowerLady
@TheLawnmowerLady 10 месяцев назад
Some folks are just not too mechanically inclined. I hope he gets it serviced more often.
@jonathanodell9507
@jonathanodell9507 8 месяцев назад
Actually 4 things, you left out timing.
@TheLawnmowerLady
@TheLawnmowerLady 8 месяцев назад
I consider timing an inherent part of good spark. Besides the Holy Quad just doesn't have the same ring.
Далее
EASY FIX/Troy Bilt Pressure Washer No Start
9:55
Просмотров 19 тыс.
Что не так с воздухом в Корее?
00:45
Я ВЕРНУЛСЯ 🔴 | WICSUR #shorts
00:57
Просмотров 1,1 млн
Two Bad Pumps - Pressure Washer Pump Replacement
41:25
Просмотров 201 тыс.
Full Service: Tecumseh Engine on Older Craftsman Mower
17:50
Free Smoking Lawn Mower - Not an Engine Issue
33:49
Просмотров 433 тыс.
Is This Old Stihl MS170 Chainsaw Worth Fixing?
27:51
Просмотров 107 тыс.
Pressure Washer wont start! Here's how I fixed it!
18:04
Что не так с воздухом в Корее?
00:45