Types of Isolated gate drivers | Optical Isolation | Inductive Isolation | Capacitive Isolation

Подписаться 60 тыс.

Просмотров 15 тыс.

50% 1

#foolishengineer #MOSFETdriver #IsolatedGatedriver
0:00 Skip Intro
00:26 Types of isolated MOSFET drivers
01:10 Optical isolated driver
03:01 Inductive isolated driver
04:17 Capacitive Isolation
05:43 Drivers Comparison
References:
training.ti.com/ti-precision-...
downloads.codico.com/misc/New...
www.infineon.com/dgdl/Infineo...
www.ti.com/lit/ds/symlink/ucc...
More Videos:
Videos on MOSFET Drivers:
Need of Isolated MOSFET gate drivers - • Why do we use Isolated...
Dual channel Transformer Gate drives - • Double-Ended transform...
Transformer-coupled driver - • Isolated High Side MOS...
Bootstrap MOSFET driver - • How does a Bootstrap g...
High side MOSFET switching - • P-channel MOSFET as a ...
Increase MOSFET switching speed - • How to increase MOSFET...
MOSFET driver totem pole circuit - • What is Totem pole MOS...
MOSFET driver working - • What is MOSFET gate dr...
MOSFET gate resistance importance - • Why do we need gate Re...
MOSFET driver circuits - • What are MOSFET gate d...
Videos on MOSFET:
MOSFET Avalanche Ruggedness - • MOSFET Avalanche Rugge...
MOSFET Avalanche Breakdown - • What is Avalanche brea...
MOSFET Inductive switching - • MOSFET switching wavef...
MOSFET & Inductor - • MOSFET switching for a...
MOSFET SOA - • What is SOA of the MOS...
MOSFET switching - • How MOSFET switching w...
Parameters of a MOSFET - • How to select a MOSFET...
Basics of MOSFET - • Difference Between MOS...
Videos on BJT:
PNP BJT as a OV protection - • How to design PNP BJT ...
NPN BJT as a OV protection - • How to design NPN BJT ...
PNP BJT as a Switch - • How to use BJT as a sw...
NPN BJT as a Switch - • How to use BJT as a sw...
Basics of BJT - • How BJTs Work? | How T...
CCCV Charging:
Part 2 - • CCCV Battery Charging ...
Part 1 - • How does a Battery Cha...
Current Regulators:
CCC with op amp &BJT - • Constant Current Regul...
CCR with BJT & TL431 - • Constant Current Regul...
CCR with BJTs - • Constant Current Regul...
CCR with Zener diode & BJT - • Constant Current Regul...
CCR with LM317 - • Constant Current Regul...
Power Supplies:
Voltage regulator using transistor - • Voltage Regulator usin...
Full Bridge Converter - • How does a Full Bridge...
Half Bridge Converter - • How does a Half Bridge...
Zeta Converter - • How does a Zeta conver...
Cuk Converter - • How does a Cuk convert...
Buck-boost converter - • How does a Buck Boost ...
Double Ended Forward converter - • Double Ended Forward C...
Active Clamp Forward Converter - • Active Clamp Forward C...
Forward Converter - • How does a Forward con...
SEPIC converter part 2 - • SEPIC converter design...
SEPIC converter part 1 - • SEPIC converter design...
Flyback converter part 2 - • Flyback converter desi...
Flyback converter part 1 - • Flyback converter desi...
Push-pull converter part 2 - • How to design a Push p...
Push-pull converter part 1 - • How to design a Push p...
Boost converter design - • How to design a Boost ...
Buck converter design - • How to design a Buck C...
SMPS basics - • Basics of Switch Mode ...
Embedded Systems:
SPI Communication Part 3: • Advantages & Disadvant...
SPI Communication Part 2: • SPI communication Data...
SPI Communication Part 1: • Basics of SPI communic...
I2C Communication Part 3: • Advantages & Disadvant...
I2C Communication Part 2: • I2C Frame structure Un...
I2C Communication Part 1: • Basics of I2C communic...
UART Communication Part 2: • Understanding UART Com...
UART Communication Part 1: • Basics of UART Communi...
Basics of Communication: • Communication protocol...
Power Electronics:
Power Factor Correction - • Power Factor Correctio...
Power Factor - • What is Power Factor |...
Electric Vehicles:
Battery management system 2 : • How does a BMS (Batter...
Battery management system 1 : • What is a Battery Mana...
Battery basics part 4 : • Electric Vehicle batte...
Battery basics part 3 : • What are the types of ...
Battery basics part 2 : • What is SOC, SOH, SOP,...
Battery basics part 1 : • Which Battery is used ...
EV motor controllers part 2: • Motor Controllers in E...
EV motor controllers part 1: • Motor Controllers in E...
Charging of EVs: • Working of Electric Ve...
EV basics: • How does an Electric V...
EV parameters: • What is inside the Ele...
EV Motors: • Motors used in electri...
---------------------------------------------------------------------------
Check us out!
Facebook - / foolishengineer-407598...
Instagram - / foolish_engineer
Twitter - / foolisher25
Subscribe now for more videos like this!

Наука

Опубликовано:

26 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 37

@seanalvarado3339 2 года назад

Overall, good video. There is an error; UCC23513 is not an optical isolated gate driver. It’s an opto-emulated gate driver that uses capacitive isolation. A true optocoupler gate driver would be a device from Broadcom/Avago (ACPL-W302). Prop delay is much higher for traditional optocoupler gate drivers in the ~700ns range. Rather than switching frequency, CMTI (common mode transit immunity) is usually a better indication of an isolated gate drivers switching capabilities with respect to noise. Higher switching speeds increase the dV/dt experienced at the switch node. That noise can couple onto the input and cause faults if the noise is too high. A gate driver with higher CMTI rating enables higher switching frequencies. Likely more relevant to MOSFET/SiC applications rather than IGBT applications. Look forward to more videos

@FoolishEngineer 2 года назад

Thank you for your inputs! I'll check

@luiscarlosmarques3946 2 года назад

I like the Inductive isolation driver. Tks for the video.

@FoolishEngineer Год назад

Thank you so much! Please show support to my video with Super thanks and don't forget to subscribe to our channel

@arabindochandra5338 Год назад

Excellent work

@FoolishEngineer Год назад

Thank you! Cheers!

@SomeTechGuy666 10 месяцев назад

Another issue is that the low side frequently needs to measure the output current and voltage on the high side in order to adjust the modulation for proper power, etc. How does one isolate the current shut and the voltage divider on the high side from the low side ? FYI, some big IGBTs have current shunts built into them. Great video.

@Factory400 2 года назад

Excellent presentation of the critical differences in these drivers.

@FoolishEngineer 2 года назад

Thank you so much! Please show support to my video with Super thanks.

@Factory400 2 года назад

@@FoolishEngineer Do you do Patreon or similar?

@FoolishEngineer 2 года назад

No, not yet

@SomeTechGuy666 10 месяцев назад

Any comment on the isolated driver modules that use fibre optics to connect them to the control electronics ? Like Power Integration's 1SP0635V2A0D ?

@Dc_tech386 11 месяцев назад

I buy 20 tlp250 from r china the optocoupler cant drive any hide side switching when I add the boostrap on it work with a very low wattage but as soon as I connected low like a capacitor the optocoupler just stop working and heating up so is it that the tlp250 gate drive can’t driver anything and should only use to isolate?

@rameshwarshelke4633 2 года назад

Always waiting new vdo...😇

@FoolishEngineer 2 года назад

Thank you so much! Please show support to my video with Super thanks.

@randycarter2001 2 года назад

You missed one. There is a MOSFET/IGBT driver that has a solar cell output. The LED shines on a photovoltaic cell generating a voltage which can be used to turn the gate. The advantage is not requiring an isolated power supply on the load side. Disadvantage is they're only good for on/off apps not high speed switching.

@EhsanHabib 2 года назад

Can you suggest one part that can do what you describe ?

@randycarter2001 2 года назад

@@EhsanHabib TLP191B APV1121

@EhsanHabib 2 года назад

Very Interesting IC.... Very useful for Small Scale Isolated Gate Driver requirements...... But i think Foolish Engineer didn't mentioned it because its not used most applications..... M

@satasauu757 Год назад

How can we make the gate pin negative 9 volts while the MOSFET stops conducting electricity? Help me make a video thank you.

@friedmule5403 2 года назад

Great video as always, may I ask you, is there only the opto solution when we are talking about DC?

@FoolishEngineer 2 года назад

Thank you so much! Please show support to my video with Super thanks. Can you elaborate?

@edinfific2576 Год назад

@@FoolishEngineer He is wondering about transfering very slow-changing or DC signals across an isolator. Yes, the opto-coupler would be the only one, unless a DC-chopping technique is used.

@SomeTechGuy666 10 месяцев назад

The 1ED3123MC12HXUMA1 requires a power supply on the HV side. Lets say the HV side is 1200V. How do you built a ~15VDC power supply from a 1200V source ? If you power the power supply from the LV side you've lost the isolation !

@buscoparan1772 2 года назад

There are also RF transmitted isolator ICs such as SI86XX model isolators.

@FoolishEngineer 2 года назад

Cool! I'll check those

@Book_worm_1999 Год назад

I would love to watch more about application of transformer base MOSFET driver

@FoolishEngineer Год назад

Okay!

@zanelevictoria5473 2 года назад

Can you please do the application circuits, like show the whole circuit. My project is based on this.

@FoolishEngineer Год назад

Yeah, sure!

@omkarkamaji2412 11 месяцев назад

Pls show some real images of parts also if possible

@benjaminvangheluwe3079 7 месяцев назад

Does one really need these abundant ad- unstopabilities? This way, it's hardly possible to seriously follow up & study your teaching friend. On top of this, depending on who you are, many people get seriously harassed by subliminal messages provided in them. This by first navigating people's thoughts and then play these out in the footages carefully interwoven, including harassment, psychological harassment, threats of imprisonment, extradition, death threaths, torture, to name but a few ... wake up to this please. Thank you for your work. RU-vid is your worst enemy, and one must be aware of this, Benjamin.