Ultimate Under Hood Work Light on 5th Gen Toyota 4Runner - KC HiLites Cyclone LED Light

Подписаться 33 тыс.

Просмотров 6 тыс.

50% 1

Trevor and I breezed thought the install of the KC HiLites LED Cyclone lights under the hood of his 4Runner. Super easy install with amazing results.
Here are the lights that Trevor got, these are single lights
KC Hilites 1350 Clear Cyclone LED Accessory Light
amzn.to/34LQKId
Here is the under hood KC HiLites Kit
KC HiLiTES 355 Cyclone LED Universal 2-Light Under Hood Wiring Kit
amzn.to/34GUN8z
Here is the Rock Light Kit Trevor was talking about
KC HiLiTES 91027 Cyclone Red LED Rock Light Kit (6-Light system
amzn.to/2L2hg9e
These are the plastic rivets we used to install the KC Lights
Xislet 100 Pcs Plastic Rivets
amzn.to/34MggNl
The Plastic Trim and Rivet Removal Tool that everyone should have
Lisle 35260 Plastic Fastener Remover
amzn.to/34KCM9t
The only other tool you will need for this install
CRAFTSMAN Screwdriver Set, Assorted, 12-Piece
amzn.to/38AtU7i
Butt Connectors for Wiring
TICONN 200PCS Heat Shrink Butt Connectors Kit
amzn.to/3ptLq3M
Klein Tools 1010 Multi Tool Long Nose Wire Cutter, Wire Crimper, Stripper
amzn.to/3rFJJm2
Bernz-O-Matic ST2200T Micro Flame Butane Torch Kit
amzn.to/37OjJNm

Авто/Мото

Опубликовано:

27 дек 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@D6EH Год назад

Thanks for this video guys, I just used it as a guide for my install. Same location, same lights, but I went with a switch in the lower left dash. I was able to tuck the wires into the same hole that the plastic pin goes through and everything seated fine. Gave it a nice clean factory look.

@freakyflow 3 года назад

If you actually look at the link of the light kit And where they are mounted They screw right in at a lower angle giving more light on the engine bay And less in you're eyes ..But other than that the install looked spot on. On my Blazer last year i insalled a Mini LED fog light which swivels up And down Then got to thinking Someone out there would make a fortune Making a high heat resistant rechargeable adjustable LED lamp with a base fixed to the hood But you can remove the lamp with a push unlock

@ManuelGarcia-ui9zc Год назад

Hello, the video is very interesting, but where does it turn on and off with a switch?

@AdventureBuilt Год назад

Trevor wired it to his sPOD because it was easy. You can also wire it to a pressure switch.

@Bosbulls Год назад

Some advice for those clips. Those are actually pretty easy to remove and install if you know how they actually work. To remove them. Use a screwdriver and with very light pressure, screw the inside piece out. Sometimes the outside piece will want to spin as well. Just hold it with a finger. With the inner screw out, the outer clip will easily pop out. Normally the clip tool is not even needed. To install. First install the outer part of the clip. Then the inner, screw, part you can just press it in with your thumb.

@trevorschroeder6745 3 года назад

Like the mount solution

@AdventureBuilt 3 года назад

Thank you.

@glockguide Год назад

If you need to disconnect the battery’s negative you would lose the lights, correct? Anyway to work around that with your setup?

@hikesbikesbrews 3 года назад

Personally, really dislike RU-vid allowing "premiering" of videos in advance. I guess it makes sense on some big videos like a cool mini series as you've done but on a simple install video, I don't get "premiering" it days in advance. With that said though, enjoy the videos overall and still wish you would offer those shirts

@AdventureBuilt 3 года назад

Thank you very much and I know the premiering is weird but I’m hoping it gets people excited about the videos. Thanks for watching and still looking into the shirt stuff.

@jhramir 3 года назад

What is that little box next to the spod circuit box? I have that same plate with the spod and was wondering what the extra space on the plate was for?

@davidgainer900 3 года назад

Hey cool setup. Question - the lights are angled forward because the hood is tilted up around 45 degrees - does that cause them to shine in your eyes when you are working around the truck? I really like the idea but wonder if you were doing work under your truck for any length of time if it would become a distraction? Thanks!

@AdventureBuilt 3 года назад

The beam pattern is actually very wide so it isn’t bad at all. They do illuminate the area in front as well. Trevor and I actually use those lights to shoot video at night. It is great Light wide and bright.