No video :(

vespa: 2 EASY fixes against FLOODED engines | FMP - SolidPASSion |

FREAKMOPED Vespa Tuning | FMP - SolidPaSSion |

Подписаться 23 тыс.

Просмотров 11 тыс.

50% 1

the BEST vespa TIP EVER! trust me, watch it. you are affected or one of your friends.
widely UNKNOWN simple reasons why si carb engines - do NOT like warm starts / - do like to drown / - do like to get flooded.
in my opiniom, its one of the biggest #FAIL of piaggio ever. sloppy engineering. bungling. missing technical common sense. just no technical thinking at all. really really bad.
#SIcarb #FLOODEDengine
old guide:
• vespa SI24 WARM START ...
--------------------------------------------------------------------------
FOLLOW me on
insta: @FreakMoPed
fb: / freakmoped
--------------------------------------------------------------------------
FMP playlists
SI CARB setting: bit.ly/2Nicmmb
FMP otuning: bit.ly/3hLAUlA
ULTIMATE basic vespa knowledge: bit.ly/3hLgtp3
vespa 177 TUNING: bit.ly/2Ynu26s
--------------------------------------------------------------------------
like what u see? found good tips?
u can support FMP via PATREON:
/ freakmoped
_____________________________________________
DISCLAIMER: the information shown in this video, is about THIS specific hardware. it is my personal observation documented with this video. It DOESNT automatically mean, that all such parts by this producer or seller do have or will have same issues.
_____________________________________________

Опубликовано:

25 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@JanddeKock 9 месяцев назад

Thanks - I would never have worked that cover touch thing out -so you inspired me to get off my arse and re-tackle that little donkey in the garage I often hate but love so much. BUT. Neither was it that nor the pin which I changed in my last attempt. As I glanced at the float through in the slanting afternoon light I noticed it had liquid in it..... So it's it must've lost its buoyancy and so too logically it has lost its full ability to push the pin up hard enough to cut the petrol off?.... Hilariously true to form with this Italian wonder, the petrol that's gotten into the float is not leaking backing out again from any perceivable hole. So I can either drill a 1.5mm hole (in the top) to drain it and then -plug it with epoxy rather than be ripped off by the Cape Town parts mafia which will probably either not have it, or charge me $100 for one. As a postscript, I would add that if you are a habitual petrol tap turner 'off - er' ( as we Vespasians are supposed to be?) and your rubber seal on your tap is working perfectly - you may never discover any of these 3 causes until that tap no longer works properly ...oh and until the petrol that seeps into the float reaches the optimum level for the float to no longer....float

@alonerider4187 3 года назад

Thanks for ideas 👍🏻👍🏻👍🏻

@adrianpancaldi8646 3 года назад

This guy is very good!

@FreakMoPed8 3 года назад

cheers!

@nicbaracca9608 Год назад

Un. be. lievable. I have been completely puzzled for months. No mechanics could work it out. I suspected all along it would be a known issue but solved with a ball peen hammer!!?? 🙏 Thank you and your health 🍻

@FreakMoPed8 Год назад

very happy to hear that! 🍻 mate 👍

@nicbaracca9608 Год назад

Thanks

@DS-_JOCK 3 года назад

cheers for the info

@babercobaig9844 9 месяцев назад

Sir good evening. The lid is perfect i dont see any leackage from lid or screwa. Even then i see floded engine. Kindly advi e is the needle is fine then what cause this. Or there a need to agjust the height of needle. K8nd regards baber