Volvo S60 V70 DOME Interior lights LED conversion 2001-2009

Подписаться 32 тыс.

Просмотров 36 тыс.

50% 1

Correction: the 1w resistor may be too small. RU-vid member McAlpine used instead 2W resistors: "I installed the 2W resistors, they seem to be holding up fine. They are slightly bigger and it’s still important to install them such that they don’t make contact with any plastic components nearby as they do get hot and can melt the light housings."
Write-ups with details www.matthewsvolvosite.com/for...
forums.swedespeed.com/showthr...
Sites for Parts Fcpeuro.com Ipdusa.com Eeuroparts.com
Forums www.matthewsvolvosite.com/for... (US)
www.volvoforums.org.uk/forumd... (UK)
forums.swedespeed.com/forumdis...) (US)

Авто/Мото

Опубликовано:

24 янв 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@winstongrant9234 5 лет назад

There are some people on here that are making RU-vid videos that are absolutely useless. But your video clear to the point and no useless jibber-jabber thanks for the info bro

@Peppermint1 5 лет назад

Appreciate the feedback! Cheers

@jeffreybrooks8643 2 года назад

Your S60 maintenance videos are helpful and very appreciated. Thank you!

@freddygonzalez5842 6 месяцев назад

Muchas gracias por comparecer video ya que me resultó muy útil. La explicación clara y directo al punto que se requiere. Saludos desde Quito Ecuador

@brathaman 3 года назад

Thanks for the video. Very helpful.

@tiborsimon5445 2 года назад

You are awesome, thank you!

@phalaaxx 3 года назад

In S60 1k resistors do the trick pretty well and don't need to be quite powerful. 0.25W are just fine since they'll only need to dissipate less than 0.144W of heat, but are quite enough to avoid annoying dim light and also to prevent CEM (or UEM) from thinking dome lights are not working or missing. S80 seems not to store such errors and 10k resistors are also fine (unless I have problems with electronics that prevent it to register these errors and I wrongfully assume it's all fine). In this case heat dissipation should be less than 0.0144W.

@jaythe2nd38 2 года назад

Excellent

@olgaspanhoff8491 Год назад

Thanks for your help. It was tough getting this down. The 2 bulbs are staying on 24/7 2 are fine, any ideas?

@gavinbritt1349 3 года назад

I would use some higher quality led’s. I use Sylvania Zevo because they have a heat sink built in, they don’t get hot and they have a lifetime warranty. Not sure if they have that size in blue but I know they have it in white and soft yellow.

@HUB1987 4 года назад

Very good video but I used 36mm bulbs fitted perfect I also bought can bus error bulbs so no glowing when off

@Peppermint1 4 года назад

Thanks for the feedback!

@piotrkaliszczuk525 3 года назад

James, you used 36mm c5w sv8.5 bulb for all lights in interior? 4x front and 2x backseat? How about legs bulb? I would like to change my lights to philips vision... No leds

@raiderman28 2 года назад

do the foot lights need a resistor???

@Bigtime_mcalpine 5 лет назад

I put some resistors on, 1w 100 ohm on mine and the resistors over heated (rear dome) gonna try again with some 2W resistors. Will let you know how I make out.

@Peppermint1 5 лет назад

Thanks for the input! I'll pin your post as soon as you test them. Do you have similar 6-led Festoons? I'm thinking sometimes Festoons may look similar but may have a different components? Anyhow, let us know, thanks

@Bigtime_mcalpine 5 лет назад

Peppermint I installed the 2W resistors, they seem to be holding up fine. They are slightly bigger and it’s still important to install them such that they don’t make contact with any plastic components nearby as they do get hot and can melt the light housings.

@Bigtime_mcalpine 5 лет назад

Peppermint here is a link to a short video I put together for the footwell lights. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-pFg6LKxZmcE.html

@Peppermint1 5 лет назад

@@Bigtime_mcalpine Great! I'm pinning your comment to let others know

@michal5001 5 лет назад

Just use 10kOhm resistor parallel to LED bulb. It will take 0.02Watt under 14Volts. It works well in my S60 '08. LED do not glow when turned off.

@samiyldz9203 4 года назад

Can you write the length of the bulps. I don wanna buy the wrong size

@senordzabenda3271 Год назад

the correct size is 41or42mm, //i had 39mm and they fit there as well//. But in the trunk , only 41/42mm will fit.

@eniseozer5880 Год назад

dear friend size Exactly how many should I get? 31mm 36mm 39mm ?

@HUB1987 4 года назад

Can you buy lights with resistors already built into bulb

@Fredsss 3 года назад

its called canbus, you dont need em for interior lights

@HUB1987 3 года назад

@@Fredsss true but I find that bulbs with out canbus tend to stay on when ment to be off no trouble with the canbus ones

@Fredsss 3 года назад

@@HUB1987 hasnt happened to me yet , i have put cheap ones 2 euros 10pcs ob my volvo and also audi, but cheap non canbus in park light is on slightly, but depens on the led itself how much power they take, i just might have been lucky